Traditional and Advanced Ceramics

<ul><li>Preface, Committee, Organizers and Sponsors</li><li>Chapter 1: Ceramic Industrial Technology</li><li>Using Lime Mud Waste from Pulp Mill as an Additive in Brick Clay</li><li>Valorization of Mill Scale Waste by its Incorporation in Fired Clay Bricks</li><li>Study of Residual Stresses in Traditional Ceramics</li><li>Effect of Flux Materials on the Melting Characteristics of Ash Glaze</li><li>Strength Improvement of Porous Ceramics by the Surface Infiltration of Strengthening Materials</li><li>Improvement of Mechanical Properties of Lightweight Ceramics with the Addition of Alumina Fiber</li><li>Construction of a Glaze Database</li><li>Influence of Grog and Cement on Physical and Mechanical Properties of Unfired Clay Bricks</li><li>Properties of Dan Kwian, Sukhothai and Ratchaburi Pottery Clays Fired at 700 and 900 degreesC</li><li>Development of Carbon Emission Label for Local Ceramic Product</li><li>Preparation of Nanocomposite Particles from <i>Typha angustifolia</i> and Egg Shells</li><li>Foam Glass Development Using Glass Cullet and Fly Ash or Rice Husk Ash as the Raw Materials</li><li>Preparation of Xylem-Imitating Porous Ceramic by Coconut Coir and Pottery Clay</li><li>Development of Ceramic Candle Filters by Slip Casting Process</li><li>Characteristics of Automotive Glass Waste-Containing Gypsum Bodies Made from Used Plaster Mould</li><li>Effects of Waste from HDPE Catalyst Process on Melting Behaviour and Thermal Properties of White Opaque Glazes</li><li>Utilization of Rice Husk Ash and Waste Sludge from Cutting Glass Manufacturing with Angthong Pottery</li><li>Preparation and Characterization of Fly Ash and Aluminium Waste Geopolymer</li><li>Effect of Firing Temperatures on Physical Properties and Phase Evolutions of Fine Stoneware Bodies</li><li>Low-Temperature Synthesis of Cordierite Using Magnesite</li><li>Zinc Oxide Nano Walls Synthesized by Chemical Vapor Deposition</li><li>Metakaolin-Based Porous Geopolymer with Aluminium Powder</li><li>Chapter 2: Advanced Ceramics</li><li>Influence of N-Doped TiO₂ Nanocomposite Film on Hydrophilic Property of Rubber Dipping Former Surface</li><li>Microwave-Assisted Hydrothermal Synthesis and Photocatalytic Properties of Cr and La-Codoped SrTiO₃ Photocatalyst</li><li>Microwave Assisted Method on the Morphology of Aluminium Doped ZnO Nanocrystals</li><li>Morphology Controlled Flower-Like ZnO Particles Synthesized by Low Cost High Pressure Cooker</li><li>Photocatalytic Degradation of Humic Acid Using Fe³⁺ and N-Doped 3SnO₂/TiO₂ Thin Films Coated on Glass Fibers</li><li>Influence of Specimen Dimensions and Temperature on the Debinding Behavior of Alumina Feedstock</li><li>A Study of Alumina Spray Dried Granules on Packing Density and Sintering Shrinkage of Simple and Complex Shape</li><li>Effect of Sintering Conditions on Mechanical and Optical Properties of 3Y-TZP Dental Ceramic</li><li>Effect of MnCO₃ Doping on Microstructure and Electrical Properties of PSZT Ceramics</li><li>Enhancement of Dielectric Constants in Strontium Titanate through Mg and Al Doping</li><li>Photocatalytic Performance of ZnO Nanoparticles Synthesized by Microwave-Assisted Process Using Zinc-Dust Waste as a Starting Material</li><li>Effects of Manganese Addition on Phase Formation Behavior and Dielectric Properties of ((K_0.5Na_0.5)_0.935Li_0.065)NbO₃ Ceramics</li><li>Anodic Oxide Film Formed on Ti-6Al-4V at a Low Current Density in Monocalciumphosphate Monohydrate (MCPM) Electrolyte and its Biocompatibility</li><li>Dewetting Suppression of Polystyrene Thin Film Using Titanium Dioxide Nanoparticles</li><li>Synthesis of Visible-Light Responsive CdS/ZnO Nanocomposite Photocatalysts via Simple Precipitation Method</li><li>Role of Tungsten Carbide Reinforcement on Alumina Matrix Composites Fabricated by Powder Injection Moulding</li><li>Fabrication of Silicon Carbide from Rice Husk by Carbothermal-Reduction and <i>In Situ</i> Reaction Bonding Technique</li><li>Preparation of Activated Carbon and Zeolite NaA Composites from Rice Husk Charcoal for Water Filtration</li><li>Effect of Sintering Parameters and Ta₂O₅ Doping on the Microstructure and Dielectric Properties of BaTiO₃ Based Ceramics</li><li>Influence of the Laminate Configurations of Transparent Armor on its Ballistic Protection</li><li>Microstructure and Properties of TCP/HA Composite Materials</li><li>Synthesis and Characterization of La_4-<i>x</i>Sr_<i>x</i>Ni₃O_10+/-? Ruddlesden - Popper Structure</li><li>Surface Characteristics and Hydrophilicity of the as-Anodized Films Formed at High Current Density on Ti-6Al-4V in Different Electrolytes</li><li>Preparation of Calcium Phosphate Cement Utilizing Dicalcium Phosphate Dihydrate and Calcium Carbonate</li><li>Chapter 3: Glass Science and Technology</li><li>The Effect of the Si/Al Ratio on the Properties of Water Treatment Residue (WTR)-Based Geopolymers</li><li>Low Melting Glass Billets for Pot Furnace Glass Processing</li><li>Effect of Alumina Source and Soaking Time on Properties of Refractory Mortar Using as Slumping Mold</li><li>The Simple Method for Increasing Chemical Stability of Glass Bottles</li><li>Investigation of Melting Behavior of Low-Enthalpy Glass Batches</li><li>Crack Evolution from Ballistic Threats in Laminated Glass</li><li>Chapter 4: Ceramic Art and Design</li><li>Development of Engobe Samples for Dan Kwian Ceramic Body</li><li>Using Natural Fibers in Forming the Body of Ceramic Lamp</li><li>Underglaze Tissue Printing for Ceramic Artists, a Collaborative Project to Re-Appraise 19th Century Printing Skills</li><li>Using the Polka Dot Technique of Color Slip for Ceramic Decorative</li><li>The Development of Pottery Products from Nong Suea Clay</li><li>3D Printed Ceramics for Tableware, Artists/Designers and Specialist Applications</li><li>Effect of Al₂O₃, CaCO₃ and MgCO₃ on Physical Properties of Crawling Shino Glaze in Reduction Atmosphere</li></ul>