This volume of the journal contains papers presented on the 8th International Conference on Metallurgy Technology and Materials (ICMTM 2020, 1-2 August 2020, China). Articles cover recent trends and achievements made in the field of metallurgical technologies, biotechnological processes, and materials science.
This volume of the journal contains papers presented on the 8th International Conference on Metallurgy Technology and Materials (ICMTM 2020, 1-2 August 2020, China). Articles cover recent trends and achievements made in the field of metallurgical technologies, biotechnological processes, and materials science.
Reihe
Sprache
Verlagsort
Zielgruppe
Illustrationen
Illustrations, unspecified
Dateigröße
ISBN-13
978-3-0357-3700-4 (9783035737004)
DOI
Copyright in bibliographic data and cover images is held by Nielsen Book Services Limited or by the publishers or by their respective licensors: all rights reserved.
Schweitzer Klassifikation
<ul><li>Preface</li><li>Chapter 1: Properties and Processing Technologies of Structural Steel and Alloys</li><li>Simulation and Optimization of Temperature Field of Tank Cover with Super Large Diameter during the Creep Aging Forming Process</li><li>The Study on Porosity Controllable Filter Material for the Integrated Gasification Combined Cycle</li><li>Formation of Ferrosilicon Alloy at 1550 degreesC via Carbothermic Reduction of SiO<sub>2</sub> by Coal and Graphite: Implication for Rice Husk Ash Utilization</li><li>Effect of Cast and Heat Treatment Processes on Microstructure and Properties of K4169 Superalloy</li><li>Anisotropy in Compression Creep-Ageing Behavior of 2219-T3 Aluminum Alloy</li><li>Investigation on the Stress Relaxation Aging Behavior of 2195 Al-Li Alloy</li><li>Damping Performance of Material Candidates for Service at 350K</li><li>A Calculation Method for the Coupling of Temperature and Concentration during Inconel 718 Alloy Solidification</li><li>The Influences of Third Alloying Element on the Internal Friction Behavior and the Mechanical Properties in the Water Quenched Ti-12Mo Alloys</li><li>The Phase Constitutes of Ti-Mo-Based Alloys</li><li>Image Evaluation of Distribution of Carbide Particles in Repeatedly Quenched (Two and Three Times) JIS-SUJ2 Steels</li><li>Surface Observation of Induction-Heated 13Cr-2Ni-2Mo Stainless Steel after Interrupted Fatigue Testing under Rolling Contact Stress in Water</li><li>Examination of Dynamic Strain Ageing Effects during Rapid Quenching of Inconel 718 Superalloy Disc</li><li>Length-Scale-Dependent Micromechanical Modeling for Precipitate Hardening in Inconel 718 Superalloy</li><li>Arrangement Optimization and Crashworthiness Analysis of B-Pilla Solder Joint Based on Collision Safety</li><li>Detection of Hydrogen Damage in 2.25Cr1Mo0.25V by Ultrasonic Inspection</li><li>Some Issues of Repairing Manned Space Vehicles in Outer Space Using Electron Beam Welding</li><li>Chapter 2: Composites, Polymers and Coatings</li><li>Insights into the Self-Optimized Hydrophobicity of Cerium Oxide Surface under Impact Abrasive Wear</li><li>Thermal Properties of High Density Polyethylene/Poly(Vinyl Alcohol) Fiber Composites Prepared Using Laboratory Mixing Extruder</li><li>Research on Vibrating L-Box Test and Yield Value of Low Water-Cement Ratio Concrete</li><li>Influence of Cellulose Fiber Content on Morphology and Properties of Poly(Lactic Acid)/Propylene-Ethylene Copolymer/Cellulose Composites</li></ul>
