Advanced Materials, Processing and Testing Technology II

<ul><li>Preface</li><li>Chapter 1: Properties and Processing Technologies of Steel and Alloys</li><li>Microstructure and Mechanical Properties of W-High Entropy Alloy Composite by Hot Swaging</li><li>Analysis of the Crack of 304 Stainless Steel and Improvement Measures</li><li>Analysis of Microstructure and Properties of High Strength Steel for Vehicle Axle</li><li>High-Throughput Characterization of Composition and Performance of Titanium Alloys Based on Nanoindentation Technology and EPMA</li><li>Influence of Mould Slenderness Ratio on the Solidification of Heavy Ingots by Numerical Simulation</li><li>Quantitative Characterization of Heat Treatment Response in a Single Crystal Nickel-Based Superalloy</li><li>Effect of Tempering Process on Microstructure and Mechanical Properties of Low Alloyed Cast Steel</li><li>Study on Fatigue Crack Growth of Laser Melting Deposited 12CrNi2 Alloy Steel Based on XFEM</li><li>Microstructure and Mechanical Properties of Low Alloy Ultra-High Strength Steel Microalloyed with Cerium</li><li>Influence of Riser Necking Ratio and Taper on the Solidification of Heavy Ingots by Numerical Simulation</li><li>Research on Deformation Prediction Method of Laser Melting Deposited Large-Sized Parts Based on Inherent Strain Method</li><li>Research on Springback during Hot Stamping with Uniform and Local-Thickened Sheet Blanks</li><li>Experimental and Numerical Analyses of Tubular Electrohydraulic Forming Process</li><li>Effect of Annealing Temperature on Microstructure and Properties of Cold Drawn Tube</li><li>The Studies of Irradiation Hardening and RIS on IASCC of Reactor Internals Bolts</li><li>Yield Behavior of Tube Hydroforming and it's Effecti on Hollow Component Manufacturing</li><li>Chapter 2: Surfaces and Special Coatings</li><li>The Coatings Formation and Characteristic of a Low Pressure Thermal Plasma Torch</li><li>Preparation of WC/Ni Flexible Cloth Coating by Vacuum Brazing</li><li>Researching Advances in Application of Bio-Inspired Superhydrophobic Metallic Surface</li><li>Microstructure and Property of Novel ?-Fe/ (Cr, Fe)₇C₃ Lamellar Eutectics Reinforced Composite Coating</li><li>Chapter 3: Properties and Processing Technologies of Special Structural and Functional Materials</li><li>The Effect of MgO Stabilizer on the Phase Composition and Microstructure of Zirconia Metering Nozzle Matrix</li><li>The Influence of Rapid Prototyping Technology on Optimization of Automobile Energy-Absorbing Box</li><li>Effect of High Temperature Treatment in Ar Atmosphere on the Tensile Strength and Structure of SiC Fiber</li><li>Effect of Tensile Stress on Characteristics of High-Temperature Superconducting Tape</li><li>Preparation of Fe-Cu-Based Friction Material and its Adoption in Automobile Mechanical Mechanism</li><li>Cutting Behavior of Self-Lubricating Ceramic Tool in Dry Machining of 40Cr Quenched Steel</li><li>Thermal Behaviour in the Stereolithography Process for Al₂O₃ Ceramic Suspension</li><li>A High Thermoelectric Performance <i>ZT</i> in p-Type LaSe₂ Crystal</li><li>Chapter 4: Properties and Application of Polymers and Composites</li><li>Research and Prospect of Diamond/Aluminum Matrix Composites</li><li>Optimal Design of Composite Material Maintenance Structure for Aircraft Based on ANSYS Workbench</li><li>Study on Preparation of Novel Dicyclopentadiene Phenol Epoxy Resin Materials Based on Different Degrees of Polymerization</li><li>Performance Improvement of Carbon Fiber Reinforced Epoxy Composite Sports Equipment</li><li>Preparation and Mechanical Properties Analysis of Aviation Mechanical Carbon Fiber Reinforced Plastics</li><li>Chapter 5: Materials and Technologies for Electronics</li><li>The Distribution Trend of Boron Atoms in Semiconductor Silicon under High Temperature</li><li>RETRACTED: Fractal Structure in Poly(3-Alkylthiophene) Derivatives</li><li>First-Principles Study of Ag₃Sn, AgZn₃ and Ag₅Zn₈ Intermetallic Compounds</li><li>Fabrication and Investigation on the Polyimide/Al₂O₃ Composite Films via Ion Exchange Technology</li><li>Research on the Magnetron Sputtering Performance of Active Matrix Liquid Crystal Display Electronic Materials Based on Amorphous Oxide Thin Film Transistors</li><li>Effect of Laser Processing Parameters on Microhole Quality of Aluminium Nitride Ceramics</li><li>Effect of Reaction Temperature and Mixture Ratio on Polysilicon Production Process</li><li>Chapter 6: Chemical Technologies and Chemical Production</li><li>A Preparation Method of ?-Carotene Reference Standard from ?-Carotene Food Additive Based on High Speed Countercurrent Chromatography (HSCCC)</li><li>Research on the Stability of Pd-Based Multi-Component Supported Catalysts</li><li>Study on Electrochemical Oxygen Evolution Properties of Bimetallic Carbon Nan Sheets</li><li>Research Progress of N-Alkylation of Alcohol and Amine by "Hydrogen Reaction"</li><li>Chapter 7: Building Materials and Structural Elements</li><li>Stress Loss of Pre-Tensed CFRP Strips Strengthening Square R? Column</li><li>Performance Test of C60 Self-Compacting Steel Fiber Concrete</li><li>Model Test of Steel-Concrete Composite Beam Deck under Negative Moment</li><li>Effect of Initial Consolidation Stress Path on Shear Behavior of Calcareous Sand</li><li>Study on the Development and Performance of a New Concrete Antifoaming Agent</li><li>Study on Porous Structure of Porous Media in Geotechnical Materials</li><li>Asphalt Modified by Ethylene-Acrylic Acid Copolymer Ionomers: Fundamental Investigations of Mechanical and Rheological Properties</li><li>Synthesis, Characterization and Application of a Potential Chemical Sand-Fixing from Lignin Sulfonate Graft Urea-Formaldehyde Resin</li><li>A Novel Approach to Characterize the Quantity and Distribution of Microorganisms in Microbial Self-Healing Cementitious Materials</li></ul>