Corrosion. Structural Metals and Alloys (2017-2018)

<ul><li>Preface</li><li>Chapter 1: Corrosion Behaviour of Carbon and Low Alloy Carbon Steels</li><li>A Case Study on Inner Corrosion of 3%Cr Casing Steel in the CO₂ Environments</li><li>3^rd Generation Hot-Dip Galvanized Steel Sheet for Automobile Manufacturing - Interface Reactions between Zinc and Metal Oxide</li><li>Corrosion Mechanism Analysis of a 20^# Carbon Steel Lightning Rod on a Substation</li><li>Effect of Shot Peening on Microstructure and Properties of 34CrMo4 Alloy</li><li>Corrosion Behavior of Low Carbon Steel in Bioethanol Fuel Blends</li><li>Experimental Study on the Corrosion Behavior of Produced Fluid on J55 Steel during CO₂ Flooding</li><li>Study of Rust Layer of TRIP Steels in Marine Environments</li><li>Corrosion Resistance of a Gradient Surface with Cr Alloying on Low-Carbon Steel</li><li>Tribocorrosion Behaviors of D40 Steel in Artificial Seawater</li><li>Influence of Rolling Force on Corrosion Resistance of Interstitial-Free Auto Sheet Steel</li><li>The Effect of Flue Gas Environment on the Corrosion Behavior of the Sulfuric Acid Dew-Point Corrosion Resistant Steel</li><li>Chapter 2: Corrosion Performance of Stainless Steels</li><li>Effect of Chlorine Ion on the Corrosion of 316L Austenitic Stainless Steel</li><li>Corrosion Resistance of TIG Welded Joints of Stainless Steels</li><li>Deliquescence of NaCl and Atmospheric Corrosion of 316L Stainless Steel</li><li>Experimental Investigation of Parameters and its Effect on IGC Attack in Ferritic Stainless Steel 430 Weldments</li><li>Effect of Cl^- Concentration on Pitting Corrosion Property of Maraging Hardened Stainless Steel Based on Pourbaix Diagram</li><li>Mechanical and Electrochemical Properties of AISI4130/Austenitic Steels Dissimilar Welded Joints</li><li>The Effect of Sodium Chloride Concentration on Corrosion Resistance of Austenitic Stainless Steel 316L and SMA Weldment</li><li>Corrosion Resistance of Nitric Acid Passivated Cr-Ni-Mo Stainless Steel</li><li>Corrosion Characterization of AISI 304 Stainless Steel Filter</li><li>Effect of Thermal Cycle on Microstructure and Corrosion Behavior of Duplex Stainless Steel SAF 2205 Electron Beam Welded Joint</li><li>Crevice Corrosion of Duplex Stainless Steels by Cyclic Potentiodynamic Polarization and Potentiostatic Techniques</li><li>Effect of Solution Annealing Time on the Microstructure and Corrosion Resistance of Duplex Stainless Steel</li><li>The Interface Character Distribution and Intergrannular Corrosion Resistance of Duplex Stainless Steel UNS S32304</li><li>Effect of Secondary Phases Precipitation on Corrosion Resistance of Duplex Stainless Steels</li><li>Chapter 3: Corrosion Resistance of Non-Ferrous Alloys</li><li>Influence of Cr and Mn Addition and Heat Treatment on the Corrosion Behaviour of an AlSi3Mg Alloy</li><li>Effect of Structural Modification on Corrosion Behavior of Hypo Eutectic Al-Si Alloy</li><li>Evaluation on the Mechanical and Corrosion Resistance of ALDC 12 Al Alloy by Three Types of Heat Treatments</li><li>The Effect of Mg Content on Intergranular Corrosion of Al-Mg-Mn Alloys after Annealing</li><li>Effects of RE Micro-Alloying Additions on the Corrosion Behavior of an Al-Mg-Si Alloy</li><li>Corrosion Performance of Aluminum and Stannum as Beverage Packaging</li><li>Improvement of Mechanical Properties and Corrosion Resistance by Deformation Induced Precipitation in Al-Zn-Mg-Cu Alloy</li><li>Effects of the Casting Temperature in the Leakage of Zamak 5</li><li>Influence of Microstructural Parameters on the Corrosion Resistance of 7075 Aluminum Alloy</li><li>Influence of Sc Addition on the Corrosion Behavior of Medium Strength Al-Zn-Mg Alloy</li><li>Characterization of Intergranular Corrosion Defects in a 2024 T351 Aluminium Alloy</li><li>Corrosion of Aluminium Aerospace Alloys</li><li>Intergranular Corrosion Mechanism of Brazed Al-Mn-Cu-Si Alloy</li><li>Effect of Heat Treatments on Stress Corrosion Behavior of 7050 Al Alloys in 3.5% NaCl Solution</li><li>Effect of Chlorine Atoms for Development of Aluminum Corrosion</li><li>Influence of Corrosive Conditions on the Mechanical Performance of Flow Drill Screw Joints between Light Metals</li><li>Thermal Desorption Spectroscopy Study on the Hydrogen Behavior in a Plasma-Charged Aluminum</li><li>Change of Intergranular Corrosion Behavior along the Thickness in a Friction-Stir-Welded 7N01-T5 Aluminum Alloy</li><li>Corrosion Behaviors of Permanent Mold Cast Mg Alloy AJ62 with Varying Grain Structures in Automotive-Related Environments</li><li>Effect of Al Additions on Corrosion Performance of Sn-9Zn Solder in Acidic Solution</li><li>Corrosion of Sn-Zn-Bi Lead Free Solder in KOH Electrolyte</li><li>Corrosion Performance of Sn-9Zn and Sn-0.7Cuin 3.5% NaCl Solution</li><li>Effect of Phosphorus and Nickel on Electrochemical Migration of Sn-3Ag-0.7Cu Solder Paste in Simulated Body Fluid</li><li>Study on Magnetic and Corrosion Properties of Ce₁₆Fe_95-xCo_xB₈ (x=0-4) Alloys</li><li>Effect of Surface Potential Distribution on Corrosion Behavior of SnAgCu Solder/Cu Substrate Interface</li><li>Improving Corrosion Resistance of Hot Extruded Mg-Sn-Al-Ce Magnesium Alloy by Rapid Solidification</li><li>Microstructure and Phase Analyses on the Corrosion of SAC305 Solder in Na?l Solution</li><li>Effect of Ti Addition on Corrosion Properties of As-Cast and Hot-Rolled AM60 Magnesium Alloys</li><li>Electrochemical Investigation of Stellite 6 Alloy in Morpholine Corrosive Environment</li><li>Effect of Sn Addition on Corrosion Properties of As-Cast and Hot-Rolled AZ31 Magnesium Alloys</li><li>Effects of Sb and Zn Addition on Mechanical Properties and Corrosion Resistance of Sn-Ag-Cu Solders</li><li>Evaluation on the Corrosion and Wear Resistance of Welding Zone Welded with Plasma Transferred Arc Welding Method</li><li>The Effects of Water Flow Rate on Copper Corrosion</li><li>Effect of Sn and Cu on Corrosion Resistance of LaMgAlMnCoNi Type Alloys</li><li>Corrosion Properties of Sn-9Zn Solder in Acidic Solution</li><li>Polarization Study of Sn-0.7Cu Solder Alloy in 1M Hydrochloric Solution</li><li>Linear Potentiodynamic Characterization of ECAPed Biocompatible AZ91 Magnesium Alloy</li><li>Study of the Correlation between Microstructure and Corrosion Resistance of the AZ91D Magnesium Alloy</li><li>Investigation on the Dealloying Process of Mn_75-xNi₂₅Al_x (x=0, 5, 10, 15, 20 at. %) Alloy Ribbons</li><li>Electrochemical-Based Characterization of the Corrosion Fatigue Behavior of Creep-Resistant Magnesium Alloys DieMag422 and AE42</li><li>The Influence of Ni Content on the Corrosion Resistance of Cu-Ni-Sn-C-P Sintered Alloys in Poor Quality Fuel</li><li>Relationship between Microstructure and Exfoliation Corrosion in Mg-14mass%Li-3mass%Al Cold-Rolled Alloy</li><li>Effect of Sn, Zn and Bi Addition on Corrosion Characteristics of Magnesium Alloys Sintered by Spark Plasma Sintering</li><li>Corrosion Mechanisms of New Wrought Mg-Al Based Alloys Alloying with Mn, Zn and Sn</li><li>Influence of ?-Mg₁₇Al₁₂ Phase on Initial Pitting Process of AZ91D Magnesium Alloy</li><li>Chapter 4: High-Temperature Oxidation of Structural Metals</li><li>High-Temperature Corrosion of Ni₃Al+ 2.9%Cr Alloy in Ar-0.2%SO₂ Gas</li><li>Corrosion of Fe₃Al-4Cr Alloys at 1000 degreesC in N₂-0.1%H₂S Gas</li><li>High-Temperature Corrosion of Incoloy Alloy 800 in N₂/H₂S Gas</li><li>High Temperature Oxidation Behaviour of Ni-Cr-, Ti- and Fe-Based Alloys in Flowing Wet Gas Environment</li><li>Corrosion Behavior of Incoloy 825 in High Temperature Vapor Containing Sodium Chloride</li><li>Corrosion of 310S Austenitic Stainless Steel in Simulated Rocket Combustion Gas</li><li>High-Temperature Corrosion-Fatigue Behavior of Ductile Cast Irons for Exhaust Manifolds Applications</li><li>Oxidation of Experimental Ti-Si-Al Based Alloys</li><li>Local Surface Phase Stability during Cyclic Oxidation Process</li><li>Heat Resistance of Certain Structural Steels</li><li>Hot Corrosion of Alloy 617 OCC in Simulated USC Power Plant Environment</li><li>Numerical Analysis of Diffusion-Controlled Internal Corrosion by the Cellular Automata Approach</li><li>Intergranular Corrosion Sensitivity of Welded Joint of Super304H at High Temperature</li><li>Comparative Analysis on Corrosion Behavior of 316SS and 304SS in Subcritical and Supercritical Aqueous Systems</li><li>Chapter 5: Stress Corrosion Cracking of Structural Metals</li><li>Hydrogen Influence on Microstructure, Corrosion Resistance and Mechanical Properties of Low Alloy Steel and Explosively Cladded Steel Used for Hydrogen Storage Salt Caverns</li><li>Effects of Sensitization and Hydrogen on Stress Corrosion Cracking of 18-8 Type Stainless Steel</li><li>Stress Corrosion Cracking of NiCrMoV Steel Welded Joint under Applied Load in Simulated Environment of Low Pressure Nuclear Steam Turbine</li><li>About the Role of Hydrogen in Stress Corrosion Cracking of a 7xxx Aluminium Alloy (Al-Zn-Mg)</li><li>Mechanical Fields on Cross-Shaped Specimens for Stress Corrosion Cracking of Cold-Worked Austenitic Stainless Steels</li><li>An Experimental Method to Evaluate the Effect of Welding Residual Stress on Corrosion Fatigue Properties of Structural Steel in Synthetic Seawater</li><li>A Grain-Scale Model of Inter-Granular Stress Corrosion Cracking in Polycrystals</li><li>Chapter 6: Corrosion Degradation of Turbine Units</li><li>Analysis of Corrosion Attack on Kaplan Turbine Blades</li><li>The Analysis of Causes of the Damage of a Turbine Blade Made of Ti-6Al-4V Alloy</li><li>
Combining 3D Scanning with Standard Microscopy Methods for Assessment of Pitting Corrosion in Turbine Blades</li><li>Failure of a Rotating Blade of a 200 MW Steam Turbine LP Rotor and Options for Eliminating other Similar Breakdowns</li><li>Crevice Corrosion of Low-Pressure Steam Turbine Materials in the Boiler Water Contained Impurity Ions</li><li>Stainless Steels as Erosion Resistant Materials for Hydraulic Machines</li></ul>