Materials Science and Modern Manufacturing

<ul><li>Preface</li><li>Chapter 1: Polymers and Composites</li><li>Synthesis of Poly[Allyl Chloride - Co Acrylic Acid] Polymers for Nucleic Track Detection from Alpha Particles</li><li>Studying the Critical Buckling Load of FG Beam Using ANSYS</li><li>Improvement of Buckling Behavior of Composite Plates Reinforced with Hybrids Nanomaterials Additives</li><li>Improvement and Optimization of the Hardness for the Aluminum Metal Matrix Composite Using Eggshell</li><li>Characterization of Natural Rubber (NR), Polybutadiene Rubber (BR) and Styrene-Butadiene Rubber (SBR) Blends Cured in a Vulcanization System</li><li>Effects of Core Height, Cell Angle and Face Thickness on Vibration Behavior of Aircraft Sandwich Structure with Honeycomb Core: An Experimental and Numerical Investigations</li><li>Effect of Laser Surface Heat Treatment on Wear and Hardness Resistance of Metal Matrix Composite from (Al- 6061+ SiC Particles)</li><li>Production Ceramic Crude Petroleum Filters from Local Raw Materials</li><li>Synthesis Structural and Optical Properties of CMC/MgO Nanocomposites</li><li>Chapter 2: Properties and Processing Technologies of Steel and Alloys</li><li>Optimization the Machining Parameters of Electro Chemical Discharge Machining of NiTi Shape Memory Alloys</li><li>The Computational Fluid Dynamics Investigation on the Solidification of Aluminum Cast in Moulds with Different Thickness and the Influence of the Moderate Press</li><li>Incremental Forming of AA8006 Aluminum Alloys Sheet with Different Step Size</li><li>Resistance Spot Welding of Dissimilar Alloys 1008 Low Carbon Steel- 1100 Aluminum Alloy</li><li>Simulation Upper Bound Theorem to Prediction Extrusion Load</li><li>Investigation into the Distribution of Erosion-Corrosion in the Furnace Tubes of Oil Refineries</li><li>The Effect of Electrical Discharge Machining Total Heat Generated on White Layer Thickness (WLT) and Fatigue Life for Die Steel</li><li>Effect Multiple Addition (TiO₂ and Fly Ash) on Wear Behavior and Hardness of 2024 Al Alloy</li><li>Chapter 3: Synthesis of Nanoparticles</li><li>Synthesis and Characterization of ZnO Nanoparticles via Aloe Vera Extract</li><li>Optical and Morphological Properties of Silver Nanoparticles Synthesis by Q-Switched Nd-YAG Laser</li><li>Synthesis of Environmentally Friendly Silver Nanoparticles</li><li>Preparation and Study Optical Limiting of Gold Nps by Pulsed Laser Ablation in Distilled Water (DDDW)</li><li>Functionalization of Multi-Walled Carbon Nanotubes Using Microwave Method</li><li>Investigations on the Nonlinear Optical Properties of Eu³⁺: TiO₂ Nanoparticles via Z-Scan Technique</li><li>Chapter 4: Functional and Special Materials</li><li>Enhanced Thermoelectric Properties of the Zn_1-xCd_xSb Prepared by Solid State Microwave Synthesis</li><li>The Role of Formic Acid as Secondary Dopant and Solvent for Poly(O-Toluidine) Intrinsically Doped with Camphor Sulfonic Acid</li><li>Studying the Physical Properties of Bi-2223 Nanostructure Prepared Thermal Treatment Method</li><li>Experimental Validation of Phase Change Material Cooling Performance Integrated into Finned Heat Sink</li><li>Enhancing Thermal Properties of Steam Turbine Blades by Coating with Nanomaterials</li><li>The Effect of Nanostructured Zirconia Reinforcement on the Mechanical and Structural Properties of a Copper-Based System</li><li>The Effect of Ethanol Solvent on Characterization of MAPbI₃ Perovskite</li><li>Preparation of Solid-Super Acidic Catalyst with Improvement Physical Properties</li><li>Preparation and Characterization of (CO₃O₅, Fe₂O3: Sn) Nanocomposite for Sensitize Photoelectrodes</li><li>Optical Properties of Non-Crystalline Fluorine Doped Hematite Fe₂O₃ Thin Films Deposited by Chemical Spray Pyrolysis Technique</li><li>Chapter 5: Materials for Opto- and Microelectronics</li><li>Red Laser Irradiation Effect on the Structural Properties of MawsoniteCu₆Fe₂SnS₈ [CFTS] Thin Films Deposited via Semi-Computerized Spray Pyrolysis Technique</li><li>Enhanced UV Absorption and Low Energy Gap of Polymer Doped ZrO₂- SiC NPs</li><li>Theoretical Investigation of Electronic Transfer Rate for Au Metal Contact with Bathocuproine BCP Dye</li><li>An Investigation of the Fill Factor and Efficiency of Molecular Semiconductor Solar Cells</li><li>Effect of Cd Substitution on Structural and Optical Properties of Zn_1-xCd_xSe Thin Films</li><li>DFT Study of Chemical Adsorption of NO₂ Gas on Graphene Nano Material</li><li>Compositional, Structural and Morphological Analyses of Bulk GeS Alloy and its Thin Films</li><li>Employment of DC Sputtering for Synthesizing Nano Cadmium Oxide for Sevoflurane Anesthetic Gas Sensor</li><li>Concentration Effects on Characteristics of Gas Sensors Based on SnO₂:Sb₂O₃ Thin Films</li><li>Study of the Effect of Solvent Polarity on Transitions of Absorption and Fluorescence Spectrum of a Erythrosine Dye</li><li>Synthesis and Characterization of Chemically Sprayed Cu₂FeSnS₄ (CFTS) Thin Films: The Effect of Substrate Temperature</li><li>Noble Metal Thin Film Thickness Optimization for Sharp Surface Plasmon Resonance Reflectance Curve</li><li>Theoretical Investigation in Coherent Manipulation throughout the Calculation of the Local Density of States in FM-DQD-FM Device</li><li>Chapter 6: Biomaterials</li><li>The Mechanical Properties of the Lower Limb Socket Material Using Natural Fibers: A Review</li><li>Effect of SiO₂ and Al₂O₃ Hybrid Nano Materials on Fatigue Behavior for Laminated Composite Materials Used to Manufacture Artificial Socket Prostheses</li><li>Production of Porous Bioactive Glass (13-93)/Poly Ethylene Glycol Composite Scaffold for Bone Tissue Defects</li><li>Boosting Mechanical Properties of Orthoses - Foot Ankle by Adding Carbon Nanotube Particles</li><li>Neuronal Toxicity of CdS Nanoparticles Prepared by Laser Ablation and their Effect on Liver</li><li>Investigation on Biocompatibility and Mechanical Properties of Ti15Mg Alloy</li></ul>