Publisher's Note: Products purchased from Third Party sellers are not guaranteed by the publisher for quality, authenticity, or access to any online entitlements included with the product.
Parallel Processing With the Propeller--Made Easy!"This book should find a place on any Propellerhead's bookshelf, between Parallax's Propeller Manual and its Programming and Customizing the Multicore Propeller volumes." Make: 24
Programming the Propeller with Spin: A Beginner's Guide to Parallel Processing walks you through the essential skills you need to build and control devices using the Propeller chip and its parallel processing environment. Find out how to use each of the identical 32-bit processors, known as cogs, and make the eight cogs effectively interact with each other. The book covers Propeller hardware and software setup, memory, and the Spin language. Step-by-step projects give you hands-on experience as you learn how to:
Use Propeller I/O techniques with extensive Spin code examples
Display numbers with seven segment displays
Create accurate, controlled pulse sequences
Add a 16 character by two line LCO display
Control R/C hobby servos
Use motor amplifiers to control small motors
Run a bipolar stepper motor
Build a gravity sensor-based auto-leveling table
Run DC motors with incremental encoders
Run small AC motors
You'll also find hundreds of lines of ready-to-run documented Spin code as well as PDFs of all the schematics on McGraw-Hill's website: Downloads available at www.mhprofessional.com/computingdownload
"This book should find a place on any Propellerhead's bookshelf, between Parallax's Propeller Manual and its Programming and Customizing the Multicore Propeller volumes." Make: 24
Sprache
Verlagsort
Verlagsgruppe
McGraw-Hill Education - Europe
Zielgruppe
Produkt-Hinweis
Broschur/Paperback
Klebebindung
Illustrationen
Maße
Höhe: 232 mm
Breite: 187 mm
Dicke: 24 mm
Gewicht
ISBN-13
978-0-07-171666-6 (9780071716666)
Copyright in bibliographic data and cover images is held by Nielsen Book Services Limited or by the publishers or by their respective licensors: all rights reserved.
Schweitzer Klassifikation
Harprit Singh Sandhu, BSME, MSCerE, is the founder of Rhino Robots, Inc., a major manufacturer of both robots and computer numeric-controlled machines. He is the author of Making PIC Microcontroller Instruments and Controllers and Running Small Motors with PIC Microcontrollers.
Preface
Part I: The Propeller/SPIN System. Introduction for the Beginner; Chapter 1. A General Introduction to the Propeller Chip; Chapter 2. The Propeller Chip. An Overall Description; Chapter 3. The Hardware Setup; Chapter 4. Software Setup: The Propeller "Tool" Environment; Chapter 5. The Various Propeller Memories; Chapter 6. The How and Why of Shared Memory; Chapter 7. Understanding One Cog; Chapter 8. The Eight Cogs; Chapter 9. Special Terms and Ideas; Chapter 10. The Spin Language; Chapter 11. Tasks Suited to Parallel Processing; Part II: Input and Output: The Basic Techniques to Be Mastered--Learning by Doing; Chapter 12. General Discussion of Input/Output; Chapter 13. Binary Pulsing; Chapter 14. Setting Up a 16-Character-by-2-Line Liquid Crystal Display; Chapter 15. Binary Input and Output: Reading a Switch and Turning on an LED if Switch is Closed; Chapter 16. Reading a Potentiometer: Creating an Input We Can Vary in Real Time; Chapter 17. Creating and Reading Frequencies; Chapter 18. Reading and Creating Pulses; Part III: The Projects: Using What Was Learned to Build The Projects; Chapter 19. Seven Segment Displays: Displaying Numbers with Seven-Segment LED Displays; Chapter 20. The Metronomes; Chapter 21. Understanding a 16-Character-by-2-Line LCD Display; Chapter 22. Running Motors: A Preliminary Discussion; Chapter 23. Motor Amplifiers for Small Motors; Chapter 24. Motor Amplifiers for Small Motors; Chapter 25. Controlling a Small DC Motor; Chapter 26. Running a Stepper Motor: Bipolar, Four-Wire Motors; Chapter 27. Gravity Sensor Based Auto-Leveling Table; Chapter 28. Running DC Motors with Attached Incremental Encoders; Chapter 29. Running Small AC Motors: Controlling Inductive Loads; Part IV: Appendixes; Appendix A. LCDRoutines4 and Utilities Object Listings; Appendix B. Materials; Appendix C. Turning Cogs On and Off; Appendix D. Experiments Board; Appendix E. Debugging; Epilogue; Index
