MODULES (160 Hours)
All of the modules listed below are included in the Trainee and Instructor Guide(s). The following ISBN and pricing information is for ordering individual modules only.
Water Treatment (12.5 Hours)
Trainee $19 ISBN 978-0-13-378143-4
Instructor $19 ISBN 978-0-13-378164-9
(Module ID 03308-13) Explains water problems encountered in heating and cooling systems and identifies water treatment methods and equipment. Covers basic water testing procedures and chemistry.
Indoor Air Quality (10 Hours)
Trainee $19 ISBN 978-0-13-378144-1
Instructor $19 ISBN 978-0-13-378165-6
(Module ID 03403-13) Defines the issues associated with indoor air quality and its effect on the health and comfort of
building occupants. Provides guidelines for performing an IAQ survey and covers the equipment and methods used to monitor and control indoor air quality.
Energy Conservation Equipment (7.5 Hours)
Trainee $19 ISBN 978-0-13-378173-1
Instructor $19 ISBN 978-0-13-378166-3
(Module ID 03404-13) Covers heat recovery/reclaim devices, as well as other energy recovery equipment used to reduce energy consumption in HVAC systems.
Building Management Systems (12.5 Hours)
Trainee $19 ISBN 978-0-13-378174-8
Instructor $19 ISBN 978-0-13-378168-7
(Module ID 03405-13) Explains how computers and microprocessors are used to manage zoned HVAC systems. Provides coverage of various network protocols and systems controllers, and introduces trainees to the various means of connection and system interface.
System Air Balancing (15 Hours)
Trainee $19 ISBN 978-0-13-378157-1
Instructor $19 ISBN 978-0-13-378169-4
(Module ID 03402-13) Covers air properties and gas laws, as well as the use of psychrometric charts. Describes the tools, instruments, and procedures used to balance an air distribution system.
System Startup and Shutdown (15 Hours)
Trainee $19 ISBN 978-0-13-378158-8
Instructor $19 ISBN 978-0-13-378170-0
(Module ID 03406-13) Presents the procedures for the startup and shutdown of hot water, steam heating, chilled water, and air handling systems. Also covers the start-up and shutdown of typical cooling towers and packaged HVAC units. The procedures for both short- and long-term shutdowns are included.
Construction Drawings and Specifications (12.5 Hours)
Trainee $19 ISBN 978-0-13-378160-1
Instructor $19 ISBN 978-0-13-378171-7
(Module ID 03401-13) Teaches how to interpret drawings used in commercial construction, including mechanical drawings, specifications, shop drawings, and as-builts. Explains how to perform takeoff procedures for equipment, fittings, ductwork, and other components.
Heating and Cooling System Design (25 Hours)
Trainee $19 ISBN 978-0-13-378161-8
Instructor $19 ISBN 978-0-13-378172-4
(Module ID 03407-13) Identifies factors that affect heating and cooling loads. Explains the process by which heating and cooling loads are calculated, and how load calculations are used in the selection of heating and cooling equipment. Covers basic types of duct systems and their selection, sizing, and installation requirements.
Commercial and Industrial Refrigeration Systems (20 Hours)
Trainee $19 ISBN 978-0-13-378162-5
Instructor $19 ISBN 978-0-13-378176-2
(Module ID 03408-13) Expands on the study of product and process refrigeration equipment by describing systems used in cold storage and food processing applications, as well as transportation refrigeration. Various types of defrost systems are covered in detail.
Alternative and Specialized Heating and Cooling Systems (10 Hours)
Trainee $19 ISBN 978-0-13-378163-2
Instructor $19 ISBN 978-0-13-378177-9
(Module ID 03409-13) Describes alternative devices used to reduce energy consumption, including wood, coal, and pelletfired systems, waste-oil heaters, geothermal heat pumps, solar heating, in-floor radiant heating, and direct-fired makeup units. Also introduces application-specific computer room environmental and air turnover systems.
Fundamentals of Crew Leadership (20 Hours)
(Module ID 46101-11)
Trainee $40 ISBN 978-0-13-292245-6
Instructor $40 ISBN 978-0-13-292255-5
