Eco-Materials Processing & Design IV

<ul><li>Lead-Free Layered Perovskite Film Capacitor for Ferroelectric Random Access Memory</li><li>Effects of Fourth Alloying Additives on Interfacial Microstructure of Sn-Ag-Cu Lead-Free Soldered Joints</li><li>Effect of Viscosity of Liquid Resin on Resin Self-Alignment Capability</li><li>Application of Lead-Free Glass to Barrier Rib Materials in Plasma Display Panel</li><li>Joining and Processing in Engineering Ceramics to Metallic Materials, in Biomorphic SiC Ceramics, and in Bioactive and Bioinert Ceramics</li><li>Biocompatibility of Plasma-Sprayed Biomedical Coatings</li><li>TiO₂-Coated Plastic Optical Fibers for Purification</li><li>Porosity Variation on the Compressive Deformation of Pre-Sintered Al-Si-Fe Based Alloy</li><li>Mechanical Characteristics of Mg and its Composites Recycled from Mg Chips</li><li>Viscosity and Surface Tension of Al and Effects of Additional Element</li><li>Tin-Cobalt Alloy Plating in a Pyrophosphate Bath</li><li>Porosity-Grading Porous Materials by Centrifugal Sintering</li><li>Improvement of Strength in Porous Ceramics by Control of Additives</li><li>Microstructure and Mechanical Behavior of Porous/Dense Alumina Multilayer Composites</li><li>Microstructure and Wear Properties of Al₂O₃/TiO₂ Nanocomposites</li><li>Preparation of Fine Alumina Dispersed Ytterbia-Stabilized Cubic Zirconia Based Composites</li><li>Fracture and Tribological Behaviors of Al₂O₃ / 5 vol.% SiC Nanocomposites</li><li>Effect of Chemical Composition on the Grain Orientation of Alumina in Oxide Laminate Composites </li><li>Effect of Silicate Addition on the Microstructure Texturing of Alumina Laminate Composites </li><li>Synthesis of Calcium Sulfoaluminate Clinker Using Alunite </li><li>Effect of WC Particle Size on Grain Growth Inhibition in the WC-xVC-Co System</li><li>Mechanical and Thermal Properties of Hot-Pressed Si₃N₄ with Added AlN</li><li>Effect of Compaction Pressure on the Microstructure Evolution of Anode Substrate for SOFC Application</li><li>Properties of Hot-Pressed AlN/BN Nanocomposites </li><li>Measurement Method of Carbon Char Content from Industry Sludge</li><li>Hydrogen Treatment of Ti Scrap</li><li>Effect of Viscosity on the Separation of Copper from Al₂O₃-CaO-SiO₂-10wt%MgO Slag System</li><li>Improvement of Silver Recovery Efficiency by High-Speed Rotation</li><li>Synthesis of Ordinary Portland Cement Clinker Using Waste POSCO Sludge</li><li>Characterization of Waste Vinyl from a Farm Village and its Application to Cement Kiln Process</li><li>Characterization of Glass Abrasive Sludge and its Reutilization as a Cement Admixture</li><li>Production and Properties of Glass-Ceramic from Incinerator Fly Ash</li><li>Silica Honeycomb-Crystal Structure Prepared by Fabrication of Silica-Coated Particles</li><li>Effect of Gas Bubbling and Impeller Agitation on Degassing Kinetics during Magnesium Alloy (AZ91D) Melt Recycling - Water Model Approach</li><li>Flow Modeling in Negative-Pressure Infiltration Casting Process of Aluminum Open-Cell Fabrication </li><li>Discharged Photoelectrocatalytic System for the Enhancement of Photocatalytic Performance</li><li>Adsorption of Heavy Metal Ions onto the Surface of Metal-Incorporated Hydrous Ferric Oxide Particles</li><li>Effect of Phosphorus or Boron Addition on Water-Resistance of Water-Glass Adhesives</li><li>Fabrication and Sagging Behavior of Three-Layer Al-Si/Al-Mn-Zn/Al-Si Clad Sheets for Automotive Heat Exchanger</li><li>Improvement in Mechanical Properties of Magnesium Alloy (AZ31) Sheet Fabricated by Casting and Subsequent Plastic Working</li><li>Fabrication of Various Nano Noble Metal Composite Materials by Ecological Sono-Process</li><li>Evaporation Behavior of Magnesium under Reduced Pressure </li><li>Influence of Final Crystal with Synthesis of Basic Calcium Carbonate by Carbonation Process</li><li>Fabrication of Metastable Oxide Ceramics with Oxygen Vacancy</li><li>Sintering Behavior and Electrical Properties of (Bi_1/2 Na _1/2)_0.99Ca_0.01TiO₃ Ceramics by Two-Stage Calcination Method</li><li>Effect of Different Annealing Condition on Bake Hardenability for Environmental Automotive Panel </li><li>Preparation of TiO₂ Fiber and Its Photocatalytic Properties</li><li>Plasma Model in Aluminum Nano-Films</li><li>Effect on Compression Properties of Al Alloy Foam Materials by Added Si</li><li>Effect of TiO₂ Powder Size on the Reactivity of Photocatalyst</li><li>Mechanical Properties of Ti₃SiC₂ Synthesized by Reaction Sintering </li><li>Organism Resolution Ability of Titania Photocatalyst in Water</li><li>Synthesis and Photocatalytic Properties of Nano TiO₂ Coated on Fly Ash</li><li>Nano-Scaled Microstructure and Tensile Behavior of Spray-Formed and Subsequently Worked Al-8Fe-2Mo-2V-1Zr Alloys</li><li>Precipitation Behavior and Mechanical Properties of a Supersaturated Co-Based Superalloy</li><li>Polypyrrole-Based Methanol Sensors Prepared by Chemical and Vapor State Polymerization</li><li>Sensing Mechanism of Conducting Polymer Sensor for Volatile Organic Compounds</li><li>Apatite-Coated Titanium Dioxide Photocatalyst</li><li>Volatile Organic Gas Recognition Using Conducting Polymer Sensor Array</li><li>Fabrication and Sensing Behavior of NASICON Thick Film SO₂ Gas Sensor by Screen-Printing Method</li><li>Fabrication and Microstructure of Pt/SiO₂ Composite Membranes by a Reverse Micelle and Sol-Gel </li><li>Gas Sensing Properties of Nanocrystalline ITO Thick Films with Different Particle Sizes</li></ul>