Material Engineering and Application II

Preface
Chapter 1: Engineering Materials
Effect of Plating Thickness on Fatigue Strength of Galvanized Steel
Influence of Nano-Silica Dosage on Properties of Cement Paste Incorporating with High Calcium Fly Ash
Mechanical and Shrinkage Behaviors of Ductile Fiber-Reinforced Polymer Repair Mortar
Development of a TAPE-Agar Liquid Gel Bandage
Frequent Start-Stop Test Study of Graphene Coatings on Journal Bearings
A New Technology to Prevent the Formation of Limescale in Hot Water Supply Systems
Development of a CuFe2O4 - Reduced Graphene Oxide-Based Electrochemical Sensor for Malathion
Nano-Crystallization of Steel Surface by Slide-Burnishing
Numerical Simulation of Material Plastic Deformation Using the Drawing Forming Process of Contoured Internal Surface Tubes
Solvent Absorption and Dissolution Kinetics Modelling for the Chemical Recycling of Waste Plastic Laminates
Feasibility of Paper Production from Oil Palm Trunk Using Arrowroot Flour as a Binder
Study on Morphology Features and Mechanical Properties of Nanofibers Films Prepared by Different Composite Electrospinning Methods
Studying the Stability and Conductivity of the Composite Films via Electrospinning/Spray Process
Electrospinning/Spray: The Interaction between Graphene Nanosheets and Different Nanofibers
Tensile Properties of Cellulose-Filled Recycled Thermoplastic Composite Filaments for 3D Printing
3D Reconstruction of Microstructure for Centrifugal Casting Babbitt Lining of Bimetallic Bearing Based on Mimics
X-Ray Powder Diffraction Data and Crystal Refinement of Ternary Compound Ti4ZrSi3
The Green Preparation of Cellulose Fibrils from Oil Palm Leaf Stalk Fibers for Hydrogel Applications
Evaluation of Recycled Aggregate (RAP) Presence Impact under Indirect Tensile Strength of Bitumen Stabilized Mix with Foamed Asphalt for a Base Layer
Scanning Electron Microscope in Rocks and their Comparison with Physical-Mechanical Properties
Natural Additive to Retard the Setting of a Mortar and Increase its Resistance
Electrochemical Synthesis of Hydroxyapatite Nanosheet-Assembled Porous Structures with Bipolar Membrane
The Comparison between Mechanical Properties of Laser-Welded Ultra-High-Strength Austenitic and Martensitic Steels
Mechanical Properties of Concrete Using Treated Recycled Concrete Aggregate in Marine Environment
Failure Analysis of Spur Gears Used in Transmission System Applied on a Hand Tractor
Biofuel Production from Jatropha Bio-Oil Derived Fast Pyrolysis: Effect of Catalysts Supported
Experimental Investigation and Modelling of Claystone from Mae Moh Coal Mine, Thailand
Preliminary Investigation of Crushed Rock-Based Geopolymer for Road Applications
Hemp Fiber Reinforced Geopolymer Composites: Effects of NaOH Concentration on Fiber Pre-Treatment Process
Crushed Rock Geopolymer as a Future Road Construction Material: An Evaluation on Strength Performance and Compaction Characteristics
Response Behavior of Local Surface Failure due to Repetitive Impact of Stainless Steel
Study of Properties of 3D Printed Short Carbon Fiber Composite
High Purity Lime as an Ecologic Alternative for Construction Mortars and Pastes
Cemented Mortar Matrices Densified with Organic Additions
Evaluation of the Electrical Resistivity, Ultrasonic Pulse Velocity and Mechanical Properties in Portland Cement Pastes Type II
Characterization of Hydraulic Concrete with Polystyrene-Based Emulsion
Preparation and Performance Study of Fluorosilicone Oligomer Anti-Sticking Coatings
The Effect of Alloying on the Fractional Composition, Shape and Grain Size Distribution of the Structure Alloy GAP the Fe-Nd-B System
Optimization of Methylene Blue Adsorption via Functionalized Activated Carbon Using Response Surface Methodology with Central Composite Design
Rejection Rate Reduction of the Automotive Thermoplastic Parts in Injection Moulding Using Response Surface Methodology
Simulation of Gap Flow Field in EDM Process Uesd Oil-in-Water Working Fluid
Synthesis, Preparation and Characterization of Amine-Induced Bacterial Cellulose-Poly(Vinyl Alcohol) Semi-Interpenetrating Network Hydrogel
Effect of Substrate Temperature on the Electronic Properties of MgO Thin Films on Si (100) Grown by Electron Beam Evaporation
Button of Hydroxyapatite Composite for Craniotomy Flap Fixation: Fabrication and Mechanical Properties
Analysis of Physical and Mechanical Properties of Backhoe's Bucket Repairment with Cladding Methode
Fabrication Study of Cu-C-Ni for EDM Electrode by a Sintering Technique
Synthesis and Characterization of Active Biocarbon Material for Use in Cosmetics and Personal Care Products
Characterization of Adsorbents Derived from Palm Fiber Waste and its Potential on Methylene Blue Adsorption
Potential Activity Evaluation of Phosphorus on CoMo/Al2O3-TiO2 Catalysts to Co-Processing Model
Investigation of the Tensile and Flexural Behavior of Polylactic Acid Based Jute Fiber Bio Composite
Fatigue and Fracture Mechanism of Aluminum-Carbon Fiber Reinforced Hybrid Composites
Fatigue-Corrosion of High Strength Steels in Synthetic Seawater under Cathodic Protection
Effect of Cr and Si Contents on the Magnetic and Mechanical Properties of Fe-Cr-Si Alloys by MIM Process
Microstructure and Mechanical Properties of Laser Welded 316L SLM Parts
The Effect of Calcination Temperature on Metakaolin Characteristic Synthesized from Badau Belitung Kaolin
Flavor Quality Changes of Turbot (Psetta maxima) Stored at -2 and 0 degreesC
Investigation on Mechanical Behavior of Sisal Fiber Reinforced Polylactic Acid and Sisal/Epoxy Composites
Evaluation of Mechanical Properties of Sugarcane Reinforced Hybrid Natural Fibre Composites by Conventional Fabrication and Finite Element Method
Study of Deep Cryogenic Treatment Process Effect on Microstructure and Properties of CuBeZr Alloy
Casting of High Aluminum Content AM Series Magnesium Alloys by Using a Horizontal Twin Roll Caster
Estimation of Cold Roll Forming Characteristics of Wrought Magnesium Alloy with Tension-Compression Asymmetry
Chapter 2: Materials Properties and Application
Analogy of Non-Destructive Tests for the Detection of Defectologies in Aluminium Cylinder Heads
Surface Roughness Prediction Based on Acoustic Emission Signals in High-Precision Diamond Turning of Rapidly Solidified Optical Aluminum Grade (RSA443)
Flow Field Analysis and Experimental Investigation of Electrochemical Etching
3D FEM Study of the Flow Uniformity of Flat Polypropylene Film/Sheet Extrusion Dies
Prediction of the Fatigue Life of the SAE 5160 Carbon Steel Coil Spring Based on Strain-Life Approach
Design and Optimization of Die Body for Polymer Extrusion