Recent Advances in Materials Science and Engineering

<ul><li>Preface</li><li>Chapter 1: Properties and Processing Technologies of Steels and Alloys</li><li>The Effect of Heating Rate on Texture and Formability of Ti-Nb Stabilized Ferritic Stainless Steel</li><li>Effect of Electroslag Refining on Cleanness, Microstructure and Mechanical Properties of a Newly Developed CrNiMoWMnV Ultrahigh-Strength Steel</li><li>Effect of Friction Stir Processing on the Microstructure and Mechanical Properties of A384 Aluminum Alloy</li><li>Oxidation Characteristics of Porous Nickel Low-Chromium Binary Alloys in Air at 1273K for 100 h</li><li>Crystallographic Texture Investigation of Thick Section Friction Stir Welded AA6082 and AA5083 Using EBSD</li><li>Cyclic Behavior of Reversion-Treated Structures after Different Cold Rolling Reductions in an AISI 301LN Stainless Steel</li><li>Developing High Strength-High Toughness Low Carbon Steel Using Combined V-Ti-Micro-Alloying and Different Thermo-Mechanical Treatments</li><li>Manganese Distribution between Slag and Metal in the Egyptian Blast Furnace</li><li>Effect of Chemistry Modification, Hot Forging and Partitioning on Low Alloy Grade Tool Steel</li><li>Chapter 2: Welding, Laser Processing, Corrosion and Surface Engineering</li><li>Prominent Achievements of Laser Surface Treatment of Martensitic Stainless Steel and Alpha-Beta 6/4 Titanium Alloy</li><li>The Influence of Shielding Gas on Strength of the Laser Welded Thin Sheet Lap Welds</li><li>Comparative Study of Spot Welding and Firiction Stir Spot Welding of Al 2024-T3</li><li>Effect of Thermal Cycle on Microstructure and Corrosion Behavior of Duplex Stainless Steel SAF 2205 Electron Beam Welded Joint</li><li>Surface Treatment of AISI M2 Tool Steel by Laser Melting</li><li>Some Anionic Surfactants as Corrosion Inhibitors for Carbon Steel in Hydrochloric Acid Solution</li><li>Preparation and Characterization of an Emulsion Paint Based on Arghel Extract as an Eco-Friendly Corrosion Inhibitor</li><li>Characterization and Structure Analysis of the Anodic Film Formed on AZ31 Mg Alloy in KOH Alkaline Solution with Various Additives</li><li>Use of Gamma Ray Back Scattering Method for Corrosion Assessment in Insulated Pipes</li><li>Evaluation of the Inhibition Efficiency of a Green Inhibitor on Corrosion of Cu-Ni Alloys in the Marine Application</li><li>Chapter 3: Ceramics, Polymers and Composites</li><li>Micro-Machining of Nano-Polymer Composites Reinforced with Graphene and Nano-Clay Fillers</li><li>Tool Wear and Form Accuracy in Ultrasonic-Assisted Milling of Soda-Lime Glass</li><li>The Effect of the Structural Parameters of 3D Orthogonal Woven Composites on their Impact Responses under Different Modes of Impact</li><li>Development of a New Glass for both Visible and Near-Infrared Optical Applications</li><li>Cementing Line Configuration of Bioactive Engineered Zirconia Implants (<i>In Vivo</i> Histological Study)</li><li>Nano Titania Reinforced Limestone Cement: Physico-Mechanical Investgation</li><li>Enhancing the Wetting Properties of Polypropylene and Polyethylene Nonwoven Fabrics Using a Cost-Effective Surface Dielectric Barrier Discharge</li><li>Chapter 4: Mechanics of Materials, Simulation and Modelling Techniques</li><li>Buckling Tests for Laser-Welded Single Corrugated Core</li><li>Empirical Model for Dry Sliding Wear Behaviour of Centrifugally Cast Functionally Graded Al/SiC_p Composite</li><li>Bending Strength of Laser-Welded Sandwich Steel Panels of Ultra-High Strength Steel</li><li>Crack Width Estimation Using Feed and Cascade Forward Back Propagation Artificial Neural Networks</li><li>Ballistic Impact Simulation of Proposed Bullet Proof Vest Made of TWIP Steel, Water and Polymer Sandwich Composite Using FE-SPH Coupled Technique</li><li>Failure Analysis of Condensate Pump Shaft in Power Plant</li><li>Mechanical Properties of a "Simple Panel Structure" Manufactured of an Ultra High Strength Stainless Steel</li><li>Design Process of Durable and Lightweight Rally Car Frame from Ultra-High Strength Stainless Steel</li><li>Chapter 5: Additive Manufacturing</li><li>Design and Manufacturing of a Non-Standard Chain Parts for a Scraper Chain Conveyor: A Case Study</li><li>Design for Additive Manufacturing in Extended DFMA Process</li><li>A Short Glance on Metal 3D AM</li><li>In Implementing a Metal 3D AM Machine</li><li>DFAM Based Multi-Material 3D Printing Using Conductive and Flexible Filaments</li><li>Chapter 6: Solar Cells and Environmental Engineering</li><li>Effect of Gas Dilution Ratios and Substrate Temperature on the Structural Transition of a-Si/?c-Si Thin-Film Solar Cell Using PECVD</li><li>CH₂O Adsorption on M (M = Li, Mg and Al) Atom Deposited ZnO Nano-Cage: DFT Study</li><li>Indoor Radon Levels and Annual Effective Dose in Dwellings of Najran City, Saudi Arabia</li><li>Two-Step Synthesis of Copper Sulfide-Graphene Counter Electrode for CdS Quantum Dot Sensitized Solar Cells</li><li>Effect of Electrodes Material on the Performance of Batch Reactor Using Plasma Enhanced Technique for Wastewater Treatment</li></ul>