Recent Advances in Materials Science and Engineering

Preface
Chapter 1: Properties and Processing Technologies of Steels and Alloys
The Effect of Heating Rate on Texture and Formability of Ti-Nb Stabilized Ferritic Stainless Steel
Effect of Electroslag Refining on Cleanness, Microstructure and Mechanical Properties of a Newly Developed CrNiMoWMnV Ultrahigh-Strength Steel
Effect of Friction Stir Processing on the Microstructure and Mechanical Properties of A384 Aluminum Alloy
Oxidation Characteristics of Porous Nickel Low-Chromium Binary Alloys in Air at 1273K for 100 h
Crystallographic Texture Investigation of Thick Section Friction Stir Welded AA6082 and AA5083 Using EBSD
Cyclic Behavior of Reversion-Treated Structures after Different Cold Rolling Reductions in an AISI 301LN Stainless Steel
Developing High Strength-High Toughness Low Carbon Steel Using Combined V-Ti-Micro-Alloying and Different Thermo-Mechanical Treatments
Manganese Distribution between Slag and Metal in the Egyptian Blast Furnace
Effect of Chemistry Modification, Hot Forging and Partitioning on Low Alloy Grade Tool Steel
Chapter 2: Welding, Laser Processing, Corrosion and Surface Engineering
Prominent Achievements of Laser Surface Treatment of Martensitic Stainless Steel and Alpha-Beta 6/4 Titanium Alloy
The Influence of Shielding Gas on Strength of the Laser Welded Thin Sheet Lap Welds
Comparative Study of Spot Welding and Firiction Stir Spot Welding of Al 2024-T3
Effect of Thermal Cycle on Microstructure and Corrosion Behavior of Duplex Stainless Steel SAF 2205 Electron Beam Welded Joint
Surface Treatment of AISI M2 Tool Steel by Laser Melting
Some Anionic Surfactants as Corrosion Inhibitors for Carbon Steel in Hydrochloric Acid Solution
Preparation and Characterization of an Emulsion Paint Based on Arghel Extract as an Eco-Friendly Corrosion Inhibitor
Characterization and Structure Analysis of the Anodic Film Formed on AZ31 Mg Alloy in KOH Alkaline Solution with Various Additives
Use of Gamma Ray Back Scattering Method for Corrosion Assessment in Insulated Pipes
Evaluation of the Inhibition Efficiency of a Green Inhibitor on Corrosion of Cu-Ni Alloys in the Marine Application
Chapter 3: Ceramics, Polymers and Composites
Micro-Machining of Nano-Polymer Composites Reinforced with Graphene and Nano-Clay Fillers
Tool Wear and Form Accuracy in Ultrasonic-Assisted Milling of Soda-Lime Glass
The Effect of the Structural Parameters of 3D Orthogonal Woven Composites on their Impact Responses under Different Modes of Impact
Development of a New Glass for both Visible and Near-Infrared Optical Applications
Cementing Line Configuration of Bioactive Engineered Zirconia Implants (In Vivo Histological Study)
Nano Titania Reinforced Limestone Cement: Physico-Mechanical Investgation
Enhancing the Wetting Properties of Polypropylene and Polyethylene Nonwoven Fabrics Using a Cost-Effective Surface Dielectric Barrier Discharge
Chapter 4: Mechanics of Materials, Simulation and Modelling Techniques
Buckling Tests for Laser-Welded Single Corrugated Core
Empirical Model for Dry Sliding Wear Behaviour of Centrifugally Cast Functionally Graded Al/SiCp Composite
Bending Strength of Laser-Welded Sandwich Steel Panels of Ultra-High Strength Steel
Crack Width Estimation Using Feed and Cascade Forward Back Propagation Artificial Neural Networks
Ballistic Impact Simulation of Proposed Bullet Proof Vest Made of TWIP Steel, Water and Polymer Sandwich Composite Using FE-SPH Coupled Technique
Failure Analysis of Condensate Pump Shaft in Power Plant
Mechanical Properties of a "Simple Panel Structure" Manufactured of an Ultra High Strength Stainless Steel
Design Process of Durable and Lightweight Rally Car Frame from Ultra-High Strength Stainless Steel
Chapter 5: Additive Manufacturing
Design and Manufacturing of a Non-Standard Chain Parts for a Scraper Chain Conveyor: A Case Study
Design for Additive Manufacturing in Extended DFMA Process
A Short Glance on Metal 3D AM
In Implementing a Metal 3D AM Machine
DFAM Based Multi-Material 3D Printing Using Conductive and Flexible Filaments
Chapter 6: Solar Cells and Environmental Engineering
Effect of Gas Dilution Ratios and Substrate Temperature on the Structural Transition of a-Si/?c-Si Thin-Film Solar Cell Using PECVD
CH2O Adsorption on M (M = Li, Mg and Al) Atom Deposited ZnO Nano-Cage: DFT Study
Indoor Radon Levels and Annual Effective Dose in Dwellings of Najran City, Saudi Arabia
Two-Step Synthesis of Copper Sulfide-Graphene Counter Electrode for CdS Quantum Dot Sensitized Solar Cells
Effect of Electrodes Material on the Performance of Batch Reactor Using Plasma Enhanced Technique for Wastewater Treatment