IUMRS International Conference in Asia

<ul><li>Chapter 1.1: Highly Efficient Structural Alloys</li><li>Effect of Trace Element Hf on the Precipitation Process and Recrystallization Resistance of Al-Er-Zr Alloys</li><li>Hot Deformation Behavior and Constitutive Equation of 5E61 Aluminum Alloy</li><li>Effect of Deformation Temperature on Texture Evolution of TLM Titanium Alloy</li><li>Effect of A-EMS above Liquidus Temperature on Structure Refinement of Al-11%Zn-3%Mg-1%Cu-0.13%Zr Alloy</li><li>Microstructure, Mechanical and Corrosion Properties of 5E61 Alloy</li><li>The Effect of the Erbium Content on the Microstructure and Mechanical Property of 6061 Aluminum Alloys</li><li>Thermal Stability of Nanocrystalline Ti6Al4V Produced by Surface Mechanical Attrition Treatment</li><li>Effect of Homogenization Temperature on the Microstructure and Property of 6061 Aluminum Alloy with Erbium</li><li>Microstructure and Mechanical Properties of Mg-Er-Zn Alloys with LPSO Phase</li><li>Effect of Cooling Rate on Hot Tearing Behavior of Mg-9Al-1Zn-0.8Ce Alloy</li><li>Effect of Nd Addition on the Microstructure, Mechanical and Corrosion Properties of Mg-Zn-Y-Nd Alloys</li><li>Numerical Simulation and Experimental Verification of Microstructure Evolution during the Seamless Tube Extrusion of Semi-Continuous Casting AZ31 Magnesium Alloy</li><li>Influence of Initial Microstructure on the Hot Working Flow Stress of Mg-3Al-1Zn Alloy</li><li>Effect of Rare-Earth Element Y on the Microstructure and Mechanical Properties of the Mg-6.0wt.%Zn-0.5wt.%Zr Alloy</li><li>Microstructure and Mechanical Property of Mg-Sn-Al Wrought Magnesium Alloys</li><li>Effects of Electromagnetic Stirring Frequency on the Microstructure and Mechanical Properties of Al-7Si-0.42 Mg-0.1Cu Alloy by Semi-Solid Processing</li><li>Protective Ability of Graphite Powder on Molten AZ91D Magnesium Alloy</li><li>Microstructure Evolution of the Mg-3Zn-0.5Er Alloy during Hot Rolling</li><li>Effect of Nd Content and Heat Treatment on Microstructure and Mechanical Properties of Mg-Zn-Nd Alloy</li><li>Effects of Al-Ti-B-Sr Master Alloy on the Microstructure and Mechanical Properties of A356 Alloy</li><li>Effect of Hot Deformation Parameters on Flow Behavior and Microstructure of Ti-6Al-4V-0.2O Alloy</li><li>Microstructure Evolution of Mg-4.5Zn-0.75Er Alloy Containing I-Phase during Hot Compression</li><li>Microstructure Evolution and Properties of 7A56 Aluminum Alloy by Homogenization</li><li>Numerical Simulation of the Forming Limit of Superplastic AZ31B Magnesium Alloy Sheet</li><li>Microstructure and Properties of Rolled Magnesium Alloy Thick Plate at Different Positions</li><li>A High Strength and Toughness Mg-Y-Ni Alloy with a Long-Period Stacking Ordered Structure</li><li>Improvement of Mechanical Properties and Corrosion Resistance by Deformation Induced Precipitation in Al-Zn-Mg-Cu Alloy</li><li>Effects of Extrusion Ratio on Microstructures and Properties of Al-Cu-Mg-Ag-Ce-Er Alloy Wires</li><li>Dynamic Compression Properties of Ti-6Al-4V Titanium Alloy Extruded Sections</li><li>Improvement of ADC12 Alloy by Optimizing CSP Process Parameters via Multiple Nonlinear Regression Analysis</li><li>Precipitation Kinetics Analysis of the Cooling Process Following the Solid Solution Treatment of 7B50 Aluminum Alloy</li><li>Effect of Melt Overheating Treatment on the Melt Structure and Solidified Structures of Al₇₅Bi₉Sn₁₆ Immiscible Alloy</li><li>Analysis of Twinning Behavior of Ti-2V Alloy Compressed at High Strain Rate</li><li>Improvement of Mechanical Properties and <i>In Vitro</i> Degradation Resistance of Biodegradable Mg-1.5Zn-0.6Zr-0.2Sc Alloy by Extrusion</li><li>Effect of Cooling Rates on the Solidification and Microstructure of Rapidly Solidified Mg_70.8Zn₂₈Nd_1.2 Quasicrystal Alloy</li><li>Effects of A-EMS on Microstructure and Mechanical Properties of DC Casting Al-10Si-1.1Ni Alloy</li><li>Influence of Yb Modification on the Microstructure and Mechanical Properties of A356.2 Aluminum Alloy</li><li>Microstructure of As-Cast 7085 Aluminum Alloy by Homogenization</li><li>Microstructure Evolution and Mechanical Properties of AZ61 Mg Alloy Processed by Two-Pass Friction Stir Processing</li><li>Microstructure and Mechanical Properties of ZK60 Magnesium Alloy Prepared by Multi-Pass Friction Stir Processing</li><li>Effect of TiB on the Nucleation and Growth of ? Phase in Ti-6Al-4V-0.1B Alloy</li><li>Constitutive Equation and Dynamic Softening Behavior of 7A55 Aluminum Alloy during Compression at Elevated Temperatures</li><li>Microstructure Evolution and Mechanical Properties of Extruded Mg-Al-Zn-Sn Alloy Sheets</li><li>Microstructure and Creep Behaviors of As-Cast Mg-Zn-Er Alloys</li><li>Dynamic Recrystallization of Mg-8Gd-3Y-1Nd-0.5Zr Alloy during Hot Deformation</li><li>Properties of Argon Gas Atomized Ti-43Al-9V-Y Alloy Powders</li><li>Fabrication and Properties of Gas Atomized Gamma Titanium Aluminide Powders and PM Processing</li><li>Microstructure and Properties of Al-Cu-Mn Alloy with Y, Zr and (Y+Zr)</li><li>Microstructure and Mechanical Properties of TC4 Titanium Alloy Subjected to High Static Magnetic Field</li><li>Influence of Precipitation Hardening on the Sliding Wear Behavior of a Cu-Zn-Al-Mn-Si Based Brass Alloy</li><li>Effects of La Microalloying on Microstructure Evolution of Pure Copper</li><li>Effects of La and Ce Mixed Rare Earth on Microstructure and Properties of Al-Mg-Si Aluminum Alloy</li><li>Evolution of LPSO Structure of Mg-11Gd-4Y-2Zn-0.5Zr Alloy during Hot Compression Deformation at Different Temperatures</li><li>Effect of Heat Treatment on Microstructure Evolution and Mechanical Behavior of SKLB3 Alloy</li><li>Constitutive Equations for 6061 Aluminum Alloy at Elevated Temperature</li><li>Dielectric Characteristics of (Ca_0.2Sr_0.8)₃(Zr_xTi_1-x)₂O₇ Ceramics at Microwave Frequencies</li><li>Chapter 1.2: High-Temperature Alloys</li><li>Effect of Hot Isostatic Pressing on Microstructures and Mechanical Properties of IN738LC Superalloy</li><li>Effect of a High Magnetic Field on the Microstructure of Directionally Solidified NiAl-Cr(Mo)-Si Near-Eutectic Alloy at Different Withdrawal Rates</li><li>Microstructures of Low Angle Boundaries of a Third Generation Single Crystal Superalloy DD9</li><li>High Temperature Rupture Life of Nickel-Based Superalloy under Directional Solidification with High Temperature Gradient</li><li>Effect of Alloying Elements on Volume Fraction of ?' Phase in Power Metallurgy Nickel-Base Superalloy</li><li>First-Principles Investigation of Phase Stability, Elastic and Thermodynamic Properties in L1₂ Co₃(Al,Mo,Ta) Phase</li><li>Effect of Solution Treatment Temperature on the Grain Growth Behavior of Fine Grained FGH96 Superalloy</li><li>Effect of Trace Ce and B Additions on the Mechanical Properties of Nb-3Si-22Ti Alloys</li><li>Effect of Cold Working and Aging Treatment on the Mechanical Properties of Co-Ni Alloy</li><li>Oxidation Behavior of a Disk Powder Metallurgy Superalloy</li><li>Effects of HIP Process on the Microstructure and Mechanical Properties of a Cast Superalloy</li><li>Influence of Heat Treatment Temperature on the Microstructures and High Cycle Fatigue Properties of DD6 Single Crystal Superalloy</li><li>Investment Casting Defects of a Turbine Nozzle Made by K465 Alloy</li><li>Influences of W and Al on the Microstructure and Stress-Rupture Property of Re-Free Ni-Based Single Crystal Superalloys</li><li>Effect of Low-Angle Boundary on Microstructure and Stress Rupture Property of a Third Generation Single Crystal Superalloy DD10</li><li>Characteristics of Microscopic Inclusions and their Influence on Fatigue Crack Propagation in FGH96 Superalloy</li><li>Microstructure Evolution and Stress Rupture Properties of DD6 Single Crystal Superalloy after Overheating</li><li>Stabilities of Microstructure and Mechanical Properties during Long-Term Aging on FGH95 Superalloy</li><li>Hot Deformation Behavior of AA-FGH720Li Superalloy</li><li>The Precipitation Behavior of ?' Phase in Single Crystal Ni-Based DD6 Superalloy for Turbine Blade</li><li>Microstructure and Property Calculation of Three Typical Second Generation Single Crystal Superalloys</li><li>Effect of Heating Temperature on Microstructure of Directionally Solidified Ni-43Ti-7Al Alloy</li><li>Effect of Annealing on Microstructure and Tensile Properties of Ti-6.5Al-2Sn-4Zr-2Mo-2Nb-1W-0.2Si Alloy</li><li>Hot Deformation Behavior and Processing Map of a New High-Temperature Titanium Alloy</li><li>Microstructure and Mechanical Properties of Ti62421S High Temperature Titanium Alloy with Different Heat Treatments</li><li>Effect of Near-Isothermal Forging Temperature on the Microstructure and Mechanical Properties of Near ? High Temperature Titanium Alloy</li><li>Effect of Rare Earth Er on the Microstructure and Mechanical Properties of High Temperature Titanium Alloys</li><li>Effect of Forging Processes on the Microstructure and Mechanical Properties of High Temperature Titanium Alloy Containing Erbium</li><li>Temperature Memory Effect of Ti-Ni-Hf-Y High Temperature Shape Memory Alloy</li><li>Effect of Y₂O₃ Coating on the Interface and Mechanical Properties of SiC Fiber Reinforced GH4738 Composites</li><li>Chapter 1.3: High-Entropy Alloys</li><li>Periodic Maximum Entropy Random Structure Models for High-Entropy Alloys</li><li>Microstructure and Properties of the Co₂NiWV_0.5Mo_1.5, Co₂NiWV_0.5Mo₂, and Co₂NiWV_1.0Mo₂ Multi-Principal Elements Alloys</li><li>AlCrFeNi High-Entropy Coating Fabricated by Mechanical Alloying and Hot Pressing Sintering</li><li>Microstructure and Mechanical Properties of VTaTiMoAl_x Refractory High Entropy Alloys</li><li>
<i>In Situ</i> Laser Synthesis of High Entropy Alloy Coating on Ti-6Al-4V Alloy: Characterization of Microstructure and Properties</li><li>Chapter 1.4: Metallic Glasses and Amorphous Materials</li><li>Evolution and Performance of Porous Structure on the Surface of Fe₇₆Si_7.2B_9.6P_7.2 Amorphous Ribbon</li><li>Non-Isothermal Crystallization Kinetics of Mg₆₁Zn₃₅Ca₄ Glassy Alloy</li><li>Microstructure and Corrosion Behavior of Ti-Ni Based Bulk Metallic Glass Composites</li><li>Effect of B2 Phase Transformation on the Mechanical Behavior of CuZr-Based Bulk Metallic Glass Composites</li><li>Diffusion of Ce-Al Melts Measured by Sliding Cell Technique</li><li>Properties of Ni_0.5Zn_0.5Fe₂O₄/Fe₇₆Si₉B₁₀P₅ Bulk Soft Magnetic Composites by Annealing Treatment</li><li>Effect of Laser Shock Peening on the Surface Morphology of Metallic Glasses</li><li>Electrical Resistance Relaxation in La₅₅Al₂₅Ni₁₀Cu₁₀ Bulk Metallic Glass</li><li>Co-Based Bulk Metallic Glasses with Good Soft-Magnetic Properties and High Strength</li><li>Chapter 1.5: Conventional and Special Steels</li><li>Influence of Service Time on the Microstructure and High Temperature Mechanical Properties of T23 Boiler Tube</li><li>Critical Crack Tip Opening Displacement for X70 and X80 Steels - A Parametric Study</li><li>Fatigue Crack Growth Rate of High Strength Pipe Steels</li><li>The Microstructure Stability of Super304H Steel Aging at 750 degreesC</li><li>Numerical Study of the Crack-Front Constraint for SENT Specimens of X80 Pipeline Steel</li><li>Effect of Steel Properties on Buckling Pressure of Corroded Pipelines</li><li>The Effect of Twice Thermal Cycle on the Microstructure and Mechanical Properties of Coarse Grain Region in X80 Pipeline Steel</li><li>Estimation of Fracture Toughness <i>J</i>_IC by Miniature Specimen Hydraulic Bulge Test</li><li>Crack Arrest Toughness of High Grade Gas Pipeline</li><li>Effect of Aging Temperature on Microstructure and Properties of V Alloyed High Manganese Austenitic Steel</li><li>Low Temperature Mechanical Properties of Power Transmission Tower Steel</li><li>Hot Ductility of 20Cr13 Steel at High Temperature</li><li>Effect of Precipitates on Austenite Grain Growth Behavior in a Low-Carbon Nb-V Microalloyed Steel</li><li>Research on Mechanical Properties and Wear Behavior at Extremely Low Temperature of a 16Cr-6Ni Austenitic Steel</li><li>Hot Deformation and Dynamic Recrystallization Behavior of Fe-8Mn-6Al-0.2C Steel</li><li>Effect of Pre-Existing Martensite on Bainitic Transformation in Low-Temperature Bainite Steel</li><li>Deformation Behaviors and Constitutive Model of DP1000 under Different Strain Rates</li><li>Effect of Thermal Aging on Microstructural Evolution in Ferrite of Duplex Stainless Steel in Nuclear Power Plant Applications</li><li>Corrosion Resistance of a Gradient Surface with Cr Alloying on Low-Carbon Steel</li><li>Modeling the Precipitation Kinetics of Cementite in Bainite in 0.17% Carbon Steel</li><li>Tribocorrosion Behaviors of D40 Steel in Artificial Seawater</li><li>Effects of Interstitial Nitrogen Atoms on Atomic Oxygen Adsorption on Fe (001) Surface from <i>Ab Initio</i> Calculations</li><li>Chapter 1.6: Metallic Composites and Compounds</li><li>Numerical Simulation on Filling Process of SiCp/A357 Composites</li><li>Comparison of Residual Stress Measured by Diffraction Method and Matrix Etching Method in SiC Fiber Reinforced Titanium Matrix Composites</li><li>Preparation of AlB₁₂-Type Al-B Alloys</li><li>Reciprocating Wear Resistance of PTAW Deposited WC/Ni-Based Composite Overlays</li><li>Analyzing Hysteresis and Thermal Expansion Coefficient of M40/AZ91D during Thermal Cycling</li><li>Process and Properties of Ultrafine Silver-Coated Electrolytic Copper Powders</li><li>Effect of Boron on Microstructure and Properties of Sn-1.0Ag-0.5Cu Low-Silver Lead-Free Solder</li><li>Progress on Preparation, Microstructure and Property of Graphene Reinforced Aluminum Matrix Composite</li><li>Microstructure and Damping Capacity of AlN_p/Mg-Al Composites with Different Particle Contents</li><li>Preparation and Electrical Conductivity of PANI Coated Nickel Fiber</li><li>Diffusion Bonding in Fabrication TA2 Sheets Enhanced Aluminum Foam Sandwich</li><li>Effect of Spark Plasma Sintering Temperature on the Consolidation of SiC Fiber Reinforced Titanium Alloy Matrix Composites</li><li>Morphology of Intermetallic Compound and Interface Bonding State in Pure Al/Steel Clad Plates after 645 degreesC/1h Diffusion Annealing</li><li>Research Progress on Plastic Processing Techniques of Particulate Reinforced Aluminium Matrix Composites</li><li>Processing and Electrical Properties of Nano-Al₂O₃/Cu Composites</li><li>Effect of Si Content of Matrix Alloy on the Microstructure and Properties of Sip/Al-Si-Mg Composites Prepared by Pressure Infiltration Method</li><li>Effect of Mechanical Stirring and Air Pressure on the Fluidity of SiCp/A357 Composites</li><li>Fabrication and Properties of <i>In Situ</i> B₁₃P₂ Reinforced Cu-Based Composites</li><li>Effect of Annealing Treatment on the Mechanical Properties of Cu-Ni-Si/Al-Mg-Si Clad Composite Wires</li><li>
<i>In Situ</i> Observation of Diffusion Behavior and Microstructural Evolution on Interfaces in Al/Cu Bimetal</li><li>Elastic Properties, Phonon Focusing and Electronic Structures of Typical Long-Period Superstructures Al₅Ti₂ and Al₁₁Ti₅</li><li>Thermodynamic Calculation of Phase Equilibria in the Mn-RE (RE=Nd, Gd, Dy) Binary Systems</li><li>Thermodynamic Calculation of the Rare Earth Permanent Magnets: Fe-RE (RE=Ho, Er, Tm, Sm) Binary Systems</li><li>Chapter 2.1: Processing Technologies of Structural Materials</li><li>Microstructure Characterization of AZ31B Mg Alloy Welds Processed by Nd:YAG Laser Welding</li><li>Effects of Ultrasonic Impact Treatment on the Residual Stress and Microstructure of TA15 Welded Joint</li><li>Application of State of the Art Assessment for Pipeline Girth Weld</li><li>Metal Magnetic Memory Testing of Welded Joints under Fatigue Load</li><li>Microstructure and Mechanical Properties of X80 Girth Welds with Different Welding Processes</li><li>Mechanical Properties of Micro-Zones of X80 Pipeline Welding Joints</li><li>Fracture and Crack Propagation Behavior of 560 MPa Microalloyed Pipeline Steel under Different Cooling Schedules</li><li>Failure Analysis of Dissimilar Steel Weld Cracking on High and Medium Pressure Guide Pipe</li><li>Microstructure Characterization of Inertial Friction Welding Zone for Nickel-Based Superalloy FGH96</li><li>Welding Performance of Several New Rare Earth Tungsten Electrodes</li><li>Abnormal Grain Growth on the Surface of Cold-Rolled AA1235 Aluminum Plate during the Annealing Process</li><li>The Optimal Selection of Extrusion Parameters of As-Cast TC27 Titanium Alloy Based on Processing-Map</li><li>Microstructure Evolution of Hot-Extruded Cu-15Ni-8Sn Alloy with Different Extrusion Ratios</li><li>A Predictive Model of Hot Rolling Flow Stress by Multivariate Adaptive Regression Spline</li><li>Effect of Solution Treatment on Microstructure and Mechanical Properties of Hot-Extruded Cu-15Ni-8Sn Alloy</li><li>Numerical Simulation on Filling Optimization of Copper Rotor for High Efficient Electric Motors in Die Casting Process</li><li>Filling of Microarray Fabricated by Micro Powder Injection Molding</li><li>Finite Element Simulation of Chain-Die Forming U Profiles with Variable Cross-Section</li><li>Defect Formation Mechanism and Influence of Processing Parameters on Surface Quality of Copper Clad Steel Composite Wires Prepared by Core-Cladding Continuous Casting</li><li>Preparation of Micro-Hole with Large Aspect Ratio</li><li>Effects of Austenitizing Temperature and Cooling Rate on the Mechanical Properties of 36MnVS4 Steel for Automobile Engine Connecting Rod</li><li>Influence of Cooling Rate and Chemical Composition on Phase Transformation and Hardness of C70S6 Steel</li><li>Common Defect Analysis for Large Section Special Steel Forging</li><li>Manufactured Process of High Strength and High Electrical Conductivity Cu-Cr-Zr-Mg Alloy Bars</li><li>Preparation and Fundamental Research of Continuous Through-Porous Pure Aluminum Flat Pipes by Depoling Continuous Casting</li><li>Grain Refinement Mechanism and Effective Nucleation Phase of Al-5Ti-1B Master Alloy</li><li>Effect of High Density Electropulsing Current on Microstructure and Mechanical Properties of Fe-6.5wt.%Si Alloy Sheet</li><li>Microstructure and Magnetic Properties of (Nd_1-2xPr_xY_x)_2.28Fe_13.58B_1.14 Melt-Spun Alloys</li><li>Effect of Bonding Temperature on Microstructure Development during Transient Liquid Phase Bonding of Ti₂AlNb Alloy Using Ti-Zr-Cu Based Filler Alloy</li><li>Floating Behavior of Entrapped Gas in Semi-Solid Metal</li><li>Effect of Residual Stress and Microstructures on 316 Stainless Steel Treated by LSP</li><li>Pore Structure Analysis of Large Size Gasar Cu Ingot Prepared by Bridgman Method</li><li>Crack Formation Mechanism of High Silicon Steel during Twin-Roll Strip Casting</li><li>Microstructure and Properties of 1060Al/AZ31/1060Al Composite Plates Fabricated by Explosive Welding</li><li>Numerical Simulation of Temperature Field and Microstructure of a Wide Copper Plate during Warm Mold Continuous Casting</li><li>An Effective Method to Fabricate 5083 Aluminum Alloy with Excellent Corrosion Resistance</li><li>Simulation Analysis of Aluminum Circular Tube in a Two-Stage Porthole Dies Extrusion Process</li><li>Influence of Post Heat Treatment on Microstructure and Mechanical Property of Ti6Al4V Parts Produced by Selective Laser Melting</li><li>Comparison of Microstructure and Mechanical Properties of Aluminum Components Manufactured by CMT</li><li>Numerical Simulation of Hot Die Forging Process of Ti-6Al-4V Alloy Blade</li><li>Strengthening Effects of Single Particle with Different Mechanical Property on Ultra-Thin Rolling of AA1235 Aluminum Alloys</li><li>Effects of Uniaxial Strain on the Structures of Vacancy Clusters in FCC Metals</li><li>A Description of Preferential Sites for Vacancy Formation on Grain Boundaries in Copper by Structural Unit Model</li><li>Chapter 2.2: Technologies and Materials for Coatings</li><li>TiN-Al Composite Coatings on A356 Alloy by Mechanical Alloying</li><li>Ceria Coatings Prepared by Sol-Gel Approach on AZ91 Magnesium Alloy</li><li>Grain Size and Adhesion Strength of the V₈C₇ Coatings Produced <i>In Situ</i></li><li>Substrate Bias Dependent Microstructure and Properties of TC17 Titanium Alloy Coatings Deposited by Magnetron Sputtering</li><li>Electrodepositing Process of Ni-W-P/Graphene Composite Coatings</li><li>Wear and Corrosion Behaviours of FeCrNiSi Alloy Coatings by Laser Cladding</li><li>Influence of Impurities on the Microstructure and Thermal Shock Resistance of YSZ Coatings</li><li>Microstructure, Mechanical and Tribological Properties of NbN/Ni Coatings</li><li>NbN Thin Film of Alternating Textures</li><li>Optimization of MAO Process Parameters and Effect of Subsequent Sealing Treatment on Corrosion Resistance of Aluminum Alloy</li><li>Deposition and Characterization of C-NbN/NbCN Multilayers on Si(100) Substrates</li><li>Fracture Toughness of Tungsten Carbide Reinforced Fe-Matrix Surface Composites</li><li>Microstructure and Properties of TiC Steel-Bonded Carbide Used Fe/Mo Pre-Alloyed Powder as Binder</li><li>Effect of WC and Co on the Microstructure and Properties of TiC Steel-Bonded Carbide</li><li>Selective Electrolytic Corrosion Behaviours of WC in WC-Co Cemented Carbide</li><li>New Equipment for Production of Super Hard Spherical Tungsten Carbide and other High-Melting Compounds Using the Method of Plasma Atomization of Rotating Billet</li><li>Preparation and Microstructure, Mechanical, Tribological Properties of Niobium Carbide Films</li><li>Deposition and Characterization of Reactive Magnetron Sputtered Tungsten Carbide Films</li><li>Effect of Micron-Scale SiO₂ Surface Coating on the Strength of Chemically Strengthened Glass</li><li>Structure Stability and Mechanical Property of Y₂O₃ Thin Films Deposited by Reactive Magnetron Sputtering</li><li>Thermomechanical and Thermal Gradient Mechanical Fatigue Lifetime of Thermal Barrier Coating Systems</li><li>Preparation and Properties of Heat-Dissipation Coating Filled with Carbon-Based Filler</li><li>Preparation and Characterization of a Novel Hydrogel-Based Fouling Release Coating</li><li>Preparation and Properties of Silicone Based Self-Deicing Coating</li><li>Preparation and Properties of a Self-Deicing Coating Based on Layered Double Hydroxide</li><li>Synthesis and Characterization of Magnetic Al/NiO Composite Pigments with Low Infrared Emissivity</li><li>Thermodynamic Analysis of Ni-Al-WC System during Self-Propagating High Temperature Synthesis</li><li>Preparation of Continuous Al₂O₃/Y₂O₃ Coating on Carbon Fiber by a Novel Aqueous Plasma Electrolysis</li><li>The Effect of Mill Addition of Quartz Glass on Thermal Shock Resistance of Sheet Steel Enamels</li><li>Chapter 3.1: Ceramics, Ferromagnetic Alloys and Materials</li><li>Effects of La Doping on Microstructure and Ferroelectric Properties of BLTN Lead-Free Ceramics</li><li>Synthesis and Characterization of Si₃N₄Nanopowder by RF Induction Thermal Plasma</li><li>Preparation of (K,Na)NbO₃ Powders with Wide Grain Size Distribution</li><li>Effect of Molten NaCl on the Synthesis of Ti₃SiC₂ Powders</li><li>Negative Thermal Sensitivity of La_1-xSr_xFeO₃ Films Prepared by Screen-Printing Method</li><li>Synthesis and High-Frequency Absorption Property of Flower-Like Nickel-Ferrite Composites</li><li>Dependence of Peak Frequency of Microwave Absorption for Co₂Z Composite on the Thickness</li><li>Effect of Magnetic Orientation on the Microwave Absorption Properties for Planar-Anisotropy Ce₂Fe₁₇N_3-?Powders/Silicone Composite</li><li>High Permeability of Z-Type Ferrite Sheets Directional Array</li><li>Synthesis of Uniform Barium Ferrite Powders by Co-Precipitation Method</li><li>Dielectric and Magnetic Properties of Cermets with Iron-Aluminum Dual Metallic Particles</li><li>Synthesis and Thermoelectric Properties of ZnO/Cu₂SnSe₃ Composites</li><li>Microstructure and Distribution of Low Content Elements in AlNiCo 9</li><li>Preparation of Anisotropic Nd-Lean Nd-Fe-B Magnets with Improved Coercivity</li><li>Dielectric and Conduction Properties of Lu₃NbO₇ Transparent Ceramic</li><li>Effects of Annealing on Ferroelectric, Optical and Electrically Controlled Light Scattering Properties of PLZT Transparent Ceramics</li><li>Fabrication of High Purity MgO Ceramic Targets by Hot-Isostatic Pressing</li><li>Dielectric Performance of (Pb_1-xSr_x)Nb₂O₆-NaNbO₃ Thin Film Materials System: Substitution Effects</li><li>Microstructure of Silicon Nitride Fibers at Elevated Temperatures</li><li>Combustion Synthesis: A Rapid Way for Preparing Bulk Cu₂SnSe₃ Thermoelectric Materials</li><li>Combustion Synthesis of ?-SiAlON Using 3D Ball Milling</li><li>Effect of Bimodal Granularity Distribution on the Properties of Silica-Based Ceramic Cores</li><li>Permeability Test Method of the Material for Graphite Pressure Vessel</li><li>Chapter 3.2: Semiconductors and Materials for Micro- and Optoelectronics</li><li>Surface Modification of Graphene Oxide with Pyrene Derivatives and their Photo-Switching Behaviors</li><li>Transmission Loss of Membrane-Type Acoustic Metamaterial with Negative Effective Mass</li><li>Complex Permittivity and Permeability Spectra of Nickel/Polyphenylene Sulfide Composite in Radio Frequency Range</li><li>Multi-Walled Carbon Nanotube-Alumina Nanocomposites with Dielectric Resonance-Induced Negative Permittivity Behavior</li><li>High Frequency Electrical and Magnetic Properties of Al/Epoxy Composites Prepared by Insulation Coating Process</li><li>Viscosity and Structure of KDP Aqueous Solution</li><li>Viscosity of Potassium Dihydrogen Phosphate Aqueous Solution within Magnetic Field</li><li>Effects of Deposition Rate on the Structural, Morphological and Optical Properties of Brookite TiO₂ Films Prepared by MOCVD</li><li>Structural, Electrical and Optical Properties of Ternary Al₂<i>_x</i>In_2(1-_x₎O₃ Films Prepared by Metal Organic Chemical Vapor Deposition</li><li>Effect of Doping Concentrations on Properties of Nb Doped ZnO (NZO) Ceramics Targets</li><li>Power-Efficient Phase Change Memory Using Silicon Carbide as a Buffer Layer</li><li>Growth of Single-Crystalline Tris-(8-Hydroxyquinoline) Gallium Uniform Sub-Microrods and their Optical Properties</li><li>Preparation and the Photoluminescence Properties of Er³⁺-Doped MoS₂ Thin Films</li><li>Stability of Sb₂Te Crystalline Films for Phase Change Memory</li><li>Carbon-Doped Sb-Rich Ge-Sb-Te Phase Change Material for High Speed and High Thermal Stability Phase Change Memory Applications</li><li>Enhanced Fluorescence Emission of Bonding Type Rare Earth Complexes Eu(MAA)₃Phen</li><li>Structure and Electrochemical Performance of Melamine/Graphene Aerogel Composite for Supercapacitors</li><li>Synthesis and Fluorescence Properties of a Terbium Complex with Ferrocenylazobenzoic Acid in Nanoparticles</li><li>Surface Plasmon Resonance Effect of the MoS₂/Ag System</li><li>Amorphous NiCoPt/Ce₂O₃ Nanoparticles as Highly Efficient Catalyst for Hydrogen Generation from Hydrous Hydrazine</li><li>A New Green Approach for Recovery of Metallic Tungsten through Electrolysis of Tungsten Carbide Scrap Anode in Molten Salts</li><li>Removal of NOx by Cement Raw Meal and Biochar Admixture</li><li>Preparation and Adsorption Properties of Fe/Chitosan/Fly Ash Composite</li><li>A Novel Way to Modify PTFE Membrane into Hydrophilicity</li><li>Modification of Nano Spherical-Like MnO_x/TiO₂ Catalysts with F-Doped</li><li>Experimental Study on Preparation and Operating Conditions over a Promising Monolithic Catalysts for NO_x Removal: MnO_x/TiO₂/Cordierite</li><li>Catalytic Activity of Fe-SBA-15 Prepared by Evaporation-Induced Self-Assembly (EISA) Method</li><li>Freeze-Drying Graphene Aerogels and their Adsorption Ability towards Organic Reagents</li><li>Effect of Sintering Temperature on the Structure and Properties of Attapulgite-Based Nanofibrous Membranes</li><li>Fabrication and Stability of CoAl₂O₄ Ceramic Pigment for 3D Printing</li><li>Investigation on NaCl Structure and Properties in External Electric Field</li><li>Sensing Mechanism of SnO₂ (110) Surface to NO₂: Density Functional Theory Calculations</li><li>Chapter 3.3: Building Materials and Construction Technologies</li><li>CO₂ Emission Analysis of Light Aggregate Concrete Block in China</li><li>Energy Consumption Analysis of Building with Typical External Thermal Insulation System</li><li>Effect and Mechanism of Sodium Fluosilicate on Setting Time of Cement</li><li>Influence of Triethanolamine on Strength Development and Hydration of Cementitious Systems Blended with Titanium Slag</li><li>Effect of Anhydrite on the Early Hydration Performance of Rapid Setting and Hardening Belite Sulfoaluminate Cement</li><li>Hardening Performance and Mechanism of Fluosilicate Surface Treatment Agent on Cement-Based Materials</li><li>Putting Cement to Sleep with Sucrose and Waking it up with Ca(OH)₂</li><li>Influence of Triethanolamine on the Properties of Cement-Based Materials</li><li>Effects of Aging on the Low Temperature Properties of Asphalt Binder and its Mixture</li><li>Environment Impact Analysis of Four Different Cement Production Strategies</li><li>Ecological Design of New Type Aluminum-Plastic Composite Panel Based on LCA</li><li>Influence of Quality and Replacement Rate of Recycled Coarse Aggregate on the Frost Resistance of Recycled Concrete</li><li>Influence of Preparation Process on the Performance of Strain Hardening Cementitious Composite</li><li>Effect of Testing Factors on Rietveld Quantitative Analysis of Cement-Matrix Materials</li><li>Water Erosion Resistance Performance of the Pervious Recycled Concrete</li><li>Electromagnetic Shielding Effectiveness of Nickel Fiber-Reinforced Cement Composites</li><li>Properties of the Concrete for the Slab Ballastless Track of CRTS III</li><li>Application of Polycarboxylate Superplasticizer in the Concrete</li><li>Bending Analysis of Functionally Graded Beam Resting on Elastic Foundation by Meshless SPH Method</li><li>Chapter 3.4: Composites and Polymers</li><li>Microstructure and Properties of C-S-H/PCE Nanocomposites</li><li>Preparation and Characterization of Silk Fibroin Based Antibacterial Biotextiles as Wound Dressing</li><li>Dielectric Behavior of Barium Titanate/Carbon Fibers Composites</li><li>Effect of Heat-Treatment on the Properties of PBO Fibers</li><li>Organic Functionalization and Properties of ZnO Nanosheets with Polymer Containing N-Vinyl Carbazole</li><li>Effects of Co, Zr Additions on the Magnetic Properties of Nanocomposite Nd₂Fe₁₄B/?-Fe Magnets</li><li>Impregnation Behavior of Polyamide 6 in Carbon Fibers and the Properties of their Composites</li><li>Dielectric Properties of Epoxy/Anhydride System in Long-Term Storage</li><li>Effects of Poly(Ethylene Glycol) Segment on Physical and Chemical Properties of Poly(Ether Ester) Elastomers</li><li>Structure and Compressive Property of Heterocyclic Aramid Fiber</li><li>Preparation PET Hybrided Materials by <i>In Situ</i> Polymerization for Delustered Fibers</li><li>Copolymerization Modification of PPTA with 2,5-Furandicarboxylic Acid: Towards High-Performance Material with Enhanced Solubility</li><li>Solution Blow Spun High Performance Co-Polyimide Nanofibers</li><li>Rheological Behaviors of Graphene Oxide/Polyacrylonitrile Spinning Solutions</li><li>Continuous Production of Hollow Hydrogel Fibers with Graphene Inner Wall</li><li>Electroplating of Copper on the Continuous Carbon Fibers</li><li>Effect of Draw Ratio on the Microstructure of Silk Fibroin/Graphene Oxide Hybrid Fibers</li><li>Gamma Irradiation Assisted Synthesis of Ag/rGO Composites and their Surface Properties</li><li>Effect of Surface Treatment on the Mechanical Performance of PPTA-Pulp Reinforced Rubber Composites in Supercritical Carbon Dioxide Fluid</li><li>Crystallization Behavior of Poly(3-Hydroxybutyrate-co-3-Hydroxyvalerate) with WS₂ as Nucleating Agent</li><li>Processability and Thermal Property of Poly(Phenylene Sulfide)/Graphene Nanoplatelets Nanocomposites and their Fibers</li><li>Preparation and Characterization of Antibacterial Nylon 6 Fiber</li><li>Photo-Induced Charge Generation of TiO₂ Nanotube Modified with Polymer Containing C₆₀ under Irradiation of Visible Light and its Applications</li><li>Preparation of Nano Cu-ZnO/PET Fiber for Antibacterial Application</li><li>Fully Biodegradable Films Based on Functionalized Natural Polyphenol/Poly(3-Hydroxybutyrate-co-3-Hydroxyvalerate) as a Potential Material for Food Packaging</li><li>Nanocomposites of Carbon Nanotube/Polyaniline with Pending Calix[8]Arene and their External Stimuli Response Properties</li><li>High Temperature Resistance of Polyborosilazane/Epoxy Resin Curing System</li><li>Curing Process and Heat-Resistance of Polyethersulfone Toughened Epoxy Resins</li><li>Effect of Different Factors on the Fibrillation Degree of Lyocell Fiber Based on Homogenization Treatment</li><li>Cellulose/Paraffin Composite Fibers for Thermal Energy Storage and Temperature Regulation</li><li>Preparation and Environmental Resistance of Dual-Wavelength Polypropylene Fluorescent Anti-Counterfeiting Fibers</li><li>Preparation and Properties of Copolyesters Fiber with Flame Retardant and Anti-Droplet by <i>In Situ</i> Polymerization</li><li>Functionalization of ?-ZrP by 1,2-Epoxypropane for Further Modification</li><li>Polyaniline Nanofibers Prepared with Binary Oxidant at the Presence of Para-Phenylenediamine</li><li>Preparation and Characterization of Stimuli-Responsive Poly(N-Isopropylacrylamide)/Ca-Alginate Hydrogel Fiber by Microfluidic Spinning</li><li>Doxorubicin Loading Capacity of Shell Cross-Linked Micelles with pH-Responsive Core as Anticancer Drug Delivery Nanocarriers</li><li>Synthesis of Biotinylated pH-Sensitive Glycopolymer with Different Architectures</li><li>Electromagnetic Shielding Effect of Aluminum Foam in 10~500 kV Electrical Substations</li><li>Effects of Multi-Walled Carbon Nanotubes on the Properties of Acrylonitrile Butadiene Styrene Nanocomposites Potentially Used for Fused Deposition Modeling</li><li>Effects of External Heat Radiation on Combustion and Toxic Gas Release of Flame Retardant Cables</li><li>Thermal Aging Effects on Fire Performance of the Cross-Linked Polyethylene Insulated Cable</li><li>Online Measuring Method of Interlaminar Cracks of Laminated Composite Based on Image Processing Technology</li><li>Chapter 3.5: Materials and Technologies in Chemical Engineering</li><li>Allocation of the Environmental Impact in Iron and Steel Industry</li><li>Life Cycle Assessment of Cathode Copper Production</li><li>Comparative Life Cycle Assessment of Chinese Radial Passenger Vehicle Tire</li><li>Materials Flow Analysis of Metallic Titanium in China</li><li>Substance Flow Analysis of Rare Earth Lanthanum in China</li><li>Thermal Decomposition Characteristics and Drying Process of Municipal Sludge</li><li>Extraction of the RO Phase from Steel Slag</li></ul>