Advanced Materials Engineering and Technology IV

<ul><li>Preface, Committees</li><li>Chapter 1: Materials and Technologies for Soldering and Packaging in Electronics</li><li>Intermetallic Study on the Modified Sn-3.5Ag-1.0Cu-1.0Zn Lead Free Solder</li><li>Solderability and Interfacial Intermetallic Compound (IMC) Growth of Sn-Cu-Ni Solder with Additions of Germanium</li><li>The Effects of Zinc Addition on the Microstructure, Melting Point and Microhardness of Sn-0.7Cu Lead-Free Solder Fabricated via Powder Metallurgy Method</li><li>Properties of Aluminum Matrix Composite (AMCs) for Electronic Packaging</li><li>Effects of Wetting Behavior on Gallium Addition in In-Zn Solder Alloy</li><li>The Alloying and Aging Effects on the Wettability and Intermetallic Bonding of the Sn-Zn-Cu-Bi Soldering Alloy on a Cu Substrate</li><li>Nanoindentation Study on Heat Treated Gold Wire Bonding</li><li>Directional Growth Behaviour of Intermetallic Compound of Sn3.0Ag0.5Cu/ImSn Subjected to Thermal Cycling</li><li>Nanoindentation of Sn3.0Ag0.5Cu/ENIG Solder Joint after High Temperature Storage</li><li>Solidification of Sn-3Ag-0.5Cu and Sn-0.7Cu-0.05Ni Solders</li><li>Effects of Trace Phosphorus in Sn-Cu-Ni Wave Solder Dross</li><li>Suppression of Cu₃Sn with Ni in High Cu Containing Sn-Cu Solder Alloys</li><li>Peritectic Reactions and Phase Transformations of Sn-30wt%Cu for High Temperature Pb-Free Soldering Applications</li><li>XPS Analysis of Oxide Films on Lead-Free Solders with Trace Additions of Germanium and Gallium</li><li>Improvement of Sn-0.7Cu Lead Free Solder Joints on Shear Strength with Addition of Titanium Oxide (TiO₂) Particles</li><li>Surface Roughness and Wettability of SAC/CNT Lead Free Solder</li><li>Wettability of CNT-Doped Solder under Isothermal Aging</li><li>Mechanical Interlocking on Leadframe Surface for Bondability of Au Wedge Bond</li><li>Ultrasonic Vibration in Leadframe for the Bondability for Au Wedge Bond</li><li>Wettability of Soldering Alloys at Heating by Electron Beam</li><li>Mechanical and Electrical Properties of Carbon Nanotubes Based Isotropic Conductive Adhesives</li><li>Chapter 2: Materials for Electronics, Optoelectronics and Electrotechnical Industry</li><li>Effect of Loading Amount of Glucose Precursor on Mesoporous Carbon Surface Area for Supercapacitor Electrode Application</li><li>Effect of Al Excess on the Band Structure of ZnO Using Density Functional Theory</li><li>Microwave Irradiation Assisted Synthesis of Silicon Carbide Nanotubes</li><li>Characterization of Silicon Carbide Nanowhiskers Synthesized by Microwave Heating Using Photoluminescence Spectroscopy and Fourier Transform Infrared Spectroscopy</li><li>Synthesis of Silicon Carbide Nanowhiskers from Graphite and Silica of Different Ratio by Microwave Irradiation Assisted Synthesis</li><li>Effect of Stoichiometry and Sintering Temperature on the Mechanical Properties of Zinc Ferrite (Zn_xFe_3-xO₄)</li><li>p-Type Conductivity Control in ZnO Films Grown by Molecular-Beam Epitaxy</li><li>Synthesis and Characterization of Ni_0.8Zn_0.2Fe₂O₄ Nanoparticles by Self-Combustion Technique</li><li>Synthesis of Chlorophyll Thin Film from Noni Leaves via Dip Coating Process</li><li>Properties of Y₃Fe₅O₁₂ (YIG) as Nanocatalyst for Ammonia Formation Produced from Magnetic Induction Method (MIM)</li><li>Response Surface Methodology (RSM) in Fabrication of Nanostructured Silicon</li><li>Chapter 3: Composite and Polymer Materials</li><li>Rigid Polyurethane Foam with Ionic Liquid Modified Multi Walled Carbon Nanotubes Composites</li><li>The Effects of Trans-Polyoctylene Rubber (TOR) on the Cure Characteristics and Swelling Behaviour of Activated Carbon Filled Styrene Butadiene Rubber (SBR) Vulcanizates</li><li>Composite Materials Characterization for Aircraft Application</li><li>The Influence of Blending Methods in Epoxy/PMMA Polymer Blend</li><li>Development of Seamless Pipe Based on Al/Al₂O₃ Composite Produced by Stir Casting and Centrifugal Casting</li><li>Effects of Composition and Fe on the Liquid Phase Sintered W-Brass Composites</li><li>Palm Kernel Shell Filled Recycled High-Density Polyethylene: Effect of Filler Loading</li><li>Chapter 4: Materials and Processing Technologies for Mechanical Engineering</li><li>Control of Temperature in Cutting Zone in Machining of Alloyed Case-Hardened Steels by Applying a Ceramic Tool with Wear-Resistant Coatings</li><li>Comparative Evaluation of Properties of Various Tool Materials by Area of Indentation Track in Pendulum Scratch Testing</li><li>Edge Cutting Tools for Machining of Hard-to-Cut Materials</li><li>Specifics of Application of Cutting Ceramics with Functional Coating in Turning of High-Strength Materials</li><li>Influence of Tool Rotational Speed on the Mechanical Properties of Friction Stir Welded Al-Cu-Li Alloy</li><li>Effect of Sensitization Treatment on Corrosion Properties in Austenitic Stainless Steel 304</li><li>Synthesis of Porous Anodic Alumina (PAA) on Aluminum Alloy AA6061 in Mixture of Phosphoric Acid and Oxalic Acid</li><li>The Effect of Sintering Temperature to the Microstructure of PM F75 (Co-Cr-Mo) Alloy</li><li>Two-Step Solution Heat Treatment of AlSiCu Alloy for Improvement of Mechanical Properties</li><li>A New Free-Machining Steel Containing Bismuth and Calcium</li><li>The Effect of Solution Heat Treatment on Incipient Melting of Al₂Cu Intermetallic Phase in Lightweight Materials</li><li>Ageing Response of Powder Metallurgy AZ91 and AZ91 Reinforced with Multiwall Carbon Nanotube</li><li>Microstructure and Mechanical Properties of Friction Stir Welded AA2195-T0</li><li>Thermal Aging of Dissimilar-Metal Weld Joints for Reactor Pressurized Vessels at Elevated Temperature</li><li>Microstructural Evolution of Austenitic Stainless Steel AISI304 and AISI316 Subjected to High-Temperature Thermal Aging</li><li>Effect of Concentration of Oxalic Acid on the Synthesis of Porous Anodic Alumina (PAA) on Aluminum Alloy AA6061</li><li>Segregation Measurement of Inconel 718 Feedstocks Used in Low-Pressure Metal Injection Molding</li><li>Precision Hole Making on Laminates Composite: Comparison between Drilling and Punching</li><li>Chapter 5: Construction Materials</li><li>Dynamic Increase Factor of High Strength Concrete with Silica Fume at High Strain Rate Loading</li><li>Experimental Study on Internal RH of BFS Mortars at Early Age</li><li>Strength of Portland Cement with Several Composition of Bottom Ash in Different Fineness with Curing Time of 28 Days</li><li>The Barriers and Strategies of Implementing the New Building Material (Fibre Cement Wall) in Malaysia Case Study: Aurum Synergy, Perlis, Malaysia</li><li>Dolomite Quarry Waste as Sand Replacement in Sand Brick</li><li>An Experiment on Bond Properties of Reinforcements Embedded in Ultra High Performance Concrete</li><li>Bond-Slip Relation of Pretensioned Concrete Members for Various Tensioning Forces</li><li>Assessment of Reinforced Concrete Building with Soil Structure Interaction Effect under Vertical Earthquake</li><li>The Temperature Effect to the Concrete due to the Single Strike of High Electric Current</li><li>Indoor Air Quality of Fired Clay Brick Incorporated with Mosaic Sludge</li><li>Leachability of Heavy Metals from Steel Mill Sludge Incorporated in Fired Clay Brick</li><li>Leaching of Heavy Metals Using TCLP and SPLP Method from Fired Clay Brick Incorporating with Mosaic Sludge</li><li>Properties of Steel Mill Sludge Waste Incorporated in Fired Clay Brick</li><li>Experimental Study of Slurry Infiltrated Fiber Reinforced Concrete</li><li>The Chemical Composition and Fineness of Natural Cement at Different Raw Meal Proportion</li><li>Effect of Chromium (II, III) Oxide and Cobalt Oxide on the Colour and Fineness of Cement</li><li>Mechanical Properties of Volcanic Ash Based Geopolymer Concrete</li><li>Potential of Geopolymer Mortar as Concrete Repairing Materials</li><li>Review on Different Types of Geopolymer Concrete Fibres</li><li>Effect of Coal Ash Properties on Compressive Strength of Bottom Ash-Based Geopolymer Concrete</li><li>Microstructure and Mechanical Properties of Ambiently-Cured Blended Coal Ash-Based Geopolymer Concrete</li><li>Effect of NaOH Concentration on Flexural Strength, Phase Formation and Microstructural Development of Kaolin Geopolymer Ceramic</li><li>Effect of Ultra High Molecular Weight Polyethylene (UHMWPE) as Binder and Sintering Temperature in Kaolin Geopolymer Ceramics on Flexural Strength</li><li>The Use of Borax in Deterring Flash Setting of High Calcium Fly Ash Based Geopolymer</li><li>Simulation Behavior of Flexure in Reinforced Concrete Beam with Opening Reinforced with Glass Fiber Reinforced Polymer (GFRP)</li><li>Flexural Behaviour of Patch-Repair Material Made from Unsaturated Polyester Resin (UPR)-Mortar</li><li>Optical Data Support on Flexural Strength of Kaolin Coated Lumber Wood via Geopolymer Technology</li><li>Chapter 6: Biomedical Engineering and Biotechnologies</li><li>Study on a Fractional Model of Filtration Effect of Cigarette Filter Tip</li><li>Preparation and Characterization of Chitosan/Alginate Polyelectrolyte Complex Prepared by Using Calcium Tripolyphosphate Ionic Gelator</li><li>Analysis on Fluid Characteristics in Y-Shape Bifurcate Coronary Artery</li><li>Performance of Newly-Fabricated Modular Surface Plasmon Resonance (mSPR) Sensor</li><li>Simultaneous Saccharification and Co-Fermentation (SSCF) Using Banana and Pineapple Waste as Substrate</li><li>Optimization of Eugenol Ester Using Statistical Approach of Response Surface Methodology</li><li>Facile Synthesis of Activated Carbon from Swamp Taro Stalk via Single Step ZnCl₂ Activation</li><li>Synthesis and Characterization of Biomass Supported Ag, Co and Ag-Co Nanoparticles</li><li>Chapter 7: Materials and Technologies for Textile Industry</li><li>Dyeing of Nylon Fabric with Natural Dye from Cassia Fistula Fruit: A Research on Effect Metal Mordants Concentration</li><li>Dyeing Silk Fabric with Natural Dye from Longan Leaves Using Simultaneous Mordanting Method</li><li>Dyeing Properties of Nylon Fabrics with Mangrove Bark Extract via Mordanting Methods</li><li>Extraction and Tensile Behavior of High Performance <i>Hibiscus tiliceus</i> Fiber</li><li>Printing of Silk Fabric with Reactive Dye Using Flour of Wild Taro Corm as a Resist Printing Paste</li><li>Chapter 8: Materials and Technologies for Recycling and Treatment of Industrial Waste</li><li>Removal of Iron and Manganese Using Cascade Aerator and Limestone Roughing Filter</li><li>Characterization of Alum Crystals Synthesized from Waste Aluminium Beverage Cans</li><li>Removal of Cadmium and Zinc Contaminations in Landfill Leachate by Using Electrocoagulation Process</li><li>Hot Solvent Extraction Method for Recycle Epoxy Resin in Waste Printed Circuit Board with Polyethylene Glycol</li><li>Kinetics and Isotherm Studies on Nd(III) Adsorption onto Xanthated Chitosan</li><li>Tin (Sn) Recovery from Wave Soldering Lead Free Solder Dross via Hydrochloric Acid Leaching and Combustion Treatment</li><li>Removal of Iron (Fe) in Rice Husk via Citric Acid Leaching Treatment</li><li>Acid Treatment of Aluminium Dross: Properties and Application</li><li>Chapter 9: Engineering Research and Design</li><li>Landslide Simulation Using Limit Equilibrium and Finite Element Method</li><li>Correlation of Brillouin Stokes Signals and Optical-Signal-to-Noise-Ratio in Multi-Wavelength Brillouin Fiber Laser with Additional Fiber Bragg Grating</li><li>Mathematical Modelling of Stress-Strain State of Multilayer Shell Molds</li><li>Theoretical Prediction of Crack Formation in Axisymmetric Multilayer Shell Molds</li><li>Structure Characterization of Low Cost Fabricated Soft Material Built Microchannel</li><li>Maximal Predicable Time Scale of Gas Emission about Fully Mechanized Mining Face</li><li>Numerical Simulation of Pressure Loss in Largesize Annulus of Deepwater Drilling Riser</li><li>The Shielding Materials from EM Radiation for Aircraft Fuselage</li><li>SAC-OCDMA over Indoor Optical Wireless Communication (OWC) System Based on Zero Cross Correlation (ZCC) Code</li><li>Optimization of Output Coupling Ratio for Multi-Wavelength Brillouin Fiber Laser Employing FBG and DCF as Gain Medium</li></ul>