Metal Forming 2016

Excellent Formability of Light Metals Sheets by Friction Stir Incremental FormingBenefits of Using Diamond Dies for Cold Alternate Drawing of Magnesium AlloysDuctility Improvement of High Carbon Steel Wire by Alternate Wire DrawingImprovement of Ductility with Maintaining Strength of Drawn High Carbon Steel WireInfluence of Process Parameters on the Product Integrity in Friction Stir Extrusion of Magnesium AlloysManufacture of Magnesium Tubes with Gradient Hardness Distribution Using a Two-Stage Porthole Extrusion DieNumerical Optimization and Practical Implementation of the Tube Extrusion Process of Mg Alloys with Micromechanical Analysis of the Final ProductStudy on Wire Rod Drawing Process Using the Rotating DieThe Effect of Equivalent Strain on Punch Load for Cold Backward Extrusion of Copper CansThe High Speed Wire Drawing Process of Steel Wires under Fluid Frictions ConditionsEvaluation of Press Formability of Pure Titanium SheetsFormability and Surface Quality of Incrementally Formed Grade 1 Titanium Thin SheetsFormability of AA6082-T6 at Warm and Hot Stamping ConditionsFormability of Explosive Welded Mg/Al Bimetallic BarInvestigation on Hardening and Softening Behavior of Steel after Rapid Strain Rate ChangesThe Influence of the Punch Shape and the Cutting Method on the Limit Strain in the Hole Expansion TestThickness and Microstructure Analysis on Hot Gas Bulged Cup-Shaped Parts of Ti-22Al-24.5Nb-0.5MoEvaluation of Tribological Performance of Lubricants and Nitrided Die for Hot Forming of Steel Using Tapered-Plug Penetration TestExtended Conical Tube-Upsetting Test to Investigate the Evolution of Friction ConditionsIdentification of Friction Coefficient in Forging Processes by Means T-Shape Tests in High TemperatureInvestigation on Friction Conditions during a Severe Bending Deformation on a Thick PlateMeasurement of Coefficient of Friction in Hot Stamping by Hot Deep Drawing TestRelationship between Molecular Structures of Organic-Sulfur Compounds and Metal Forming PerformanceEffect of Microstructure and Mechanical Properties Formation of Medium Carbon Steel Wire through Continuous Combined DeformationInfluence of Servo Motion on Forming Limit of Thin Metallic Foils Using Micro Bulge TestInfluence of Strain Gradient on Springback of Thin Pure Titanium Foils in Microbending Assisted by Resistance HeatingMetallic Multilayered Materials Produced by Constrained CompressionMulti-Resolution Material Hardening Law for CPFE Micro-Forming AnalysisShear Banding in Polycrystalline Aluminium and Copper Pre-Deformed by ECAP and Subsequently Plane Strain CompressedA Method of Determining Unified Viscoplastic Constitutive Equations for Hot Forging SimulationsDeep Drawability and Bendability in Hot Stamping of Ultra-High Strength Steel PartsEffect of Different Quench Media on the Microstructure and Mechanical Properties of Large-Scale Low Alloy Steel ForgingsEffect of the Time between Last Deformation Pass and Accelerated Cooling on the Mechanical Properties in Nb and Nb-Mo Microalloyed SteelsEffect of Thermomechanical and Austenite Partitioning Processing on Microstructure and Mechanical Properties of 0.4 Carbon Steel Containing AluminumEnhancing the Strain-Hardening Behavior of Hadfield Steel Using Ladle Treatment TechniqueExamination of the Effect of Variation in Stress Magnitude on the Amount of Transformed Retained Austenite in the Structure of TRIP Steel WiresHot Deformation and Microstructural Characteristics of Nitrogen Enhanced 316L Stainless SteelInvestigation of Tensile and Compressive Creep Behaviour of AA2050-T34 during Creep Age Forming ProcessInvestigation of the Unloading Yield Effect in Aluminum and Magnesium Sheet Metal Alloys at Room TemperatureInvestigation of Uniaxial Tensile Properties of AA6082 under HFQ? ConditionsMicrostructural Evolution of the Magnesium Alloy AZ31 with and without SiC Particles during Ultrasonic Melt TreatmentModelling Microstructure Evolution in ATI 718Plus? AlloyModelling of Flow Behaviour of Magnesium AlloysThe Onset of the Austenite to Bainite Phase Transformation for Different Cooling Paths and Steel CompositionsAnalysis of Material Flow in Oval Upsetting Using Mild-Wedged DieConnection Strength of Additive Manufactured Tool Elements to the SubstrateDesign of a Novel End-Effector for Kinematic Support in Incremental Sheet FormingDetermination of Processing Windows for the Hot Stamping of AA7075Energy Efficient Servo Controlled Roll Levelling MachinesExperimental Investigation on Shape Evolution in Metal Forming Hybrid ProcessImprovement of Fatigue Strength of Hole Edge of Ultra-High Strength Steel Sheet by Punching Process Including ThickeningInfluence of Burnishing Conditions on Burnishing Force and Application of Coated Roller in Inclined Roller BurnishingInfluence of Cutting Processes on Edge Cracking Sensitivity of Bright Finishing AlloysInvestigation of the Relationship between Material Flow and Rollover in Double-Sided Shearing Using Image ProcessingJoining of Stepped Shaft and Disc by FormingMicrostructure and Mechanical Properties of Ti/Cu Clads Manufactured by Explosive Bonding at Different Stand-Off DistancesOptimized Cooling Strategies for Bainitic Forging SteelsPrediction of Failure Mode in Hole Clinching of Al Alloy and Advanced High-Strength SteelPrevention of Local Thinning and Springback in Hot Stamping of Thin SheetsProcess Effects in Short Cycle Stretch Forming of Tinplate Can BodiesProduction of Aluminium Based Interpenetrating Phase Composites Using Semi-Solid FormingReducing Blanking Vibration with Active Vibration Control Using a Servo PressThe Effectiveness of Cold Rolling for Residual Stress Reduction in Quenched 7050 Aluminium Alloy ForgingsUltrasonic Wave Propagation Analysis for In-Process Monitoring of StampingUltrasonic-Assisted Metal Staking with 15 kHz Oscillation FrequencyUltrasonic-Assisted Upsetting of Steel with 15 kHz Oscillation FrequencyA Comparison of Input Data Used to Represent Phase Transformations during the Quenching of a Large Nuclear ForgingA Fast Three-Dimensional Model for Strip RollingAnalysis of Void Closure during Open Die Forging Process of Large Size Steel IngotsAn Analytical and Numerical Investigation on Flange Wrinkling Behavior in Warm Forming Process of AA5754 Using Macro-Textured Tool DesignA New Approach for Void Closure in Bulk Metal FormingA New Method Predicting Contact Length and Flattening in Temper RollingComputer Simulation of the Combined Process "Helical Rolling-Pressing"Computer Simulation of Transformation during TRIP Steel Rod DrawingConstitutive Equation Development to Model the Hot Forging of ZERON?100 Super Duplex Stainless Steel and Associated Microstructural EvolutionCrack Formation and Propagation Mechanism in the Punching Process of High Tensile Strength Steel SheetDevelopment of a Process Map for Wire Drawing of Pearlitic Steel by Finite Element Analysis Coupled with Damage EvolutionDevelopment of the Technology of Various Large Bodies Manufacturing Based on Combined Methods of DeformationElastic-Plastic Thermomechanical Fatigue Analysis of Forging DiesExtension of the Freiberger Model of Spread for the Calculation of Material Flow during Rolling of Long Products to a New Material Group of Mg Alloys AZ31, AZ81, WE43Feasibility Study of Complex Sheet Hydroforming Process: Experimental and ModellingFinite Element Simulation of Heat Transfer during Cryogenic Asymmetric Sheet Rolling of Aluminum AlloysFinite Element Simulation of Shear Strain during High-Ratio Differential Speed Rolling of Aluminum Alloy 5083Influence of Die Geometry on Drawing Force in Cold Drawing of Steel Tubes Using Numerical SimulationInfluence of Material and Tribological Modelling on the Prediction of Big Size Automotive Components SpringbackInvestigation into the Numerical Model Behaviour of Belleville Washers in Cold Roll FormingModelling Central Consolidation during Hot Rolling of Cast ProductsNumerical Investigation of the Material Behaviour during Compression Tests for Samples with Rough Surfaces Represented in Different Geometry Scale FactorsNumerical Modelling of AlSi7 Tubular Components Flowformed at Elevated TemperatureParameters Design of Discontinuous Dot Indenter in Fine Blanking Process with Different Thickness WorkpiecePrediction of Forming Limit Diagram for AA5754 Using Artificial Neural Network ModellingPrediction of Localized Necking Based on Crystal Plasticity: Comparison of Bifurcation and Imperfection ApproachesAn Investigation of Direct Powder Forging of Nickel Superalloy FGH96Exploitation of Field-Assisted Sintering Technology (FAST) to Produce Pre-Forged Billets from Metastable Beta Titanium Alloy PowderMethodology for Modelling Diffusion Bonding in Powder ForgingSupercritical Debinding of Environmentally Friendly Inconel 718 Feedstock to Metal Injection Moulding ProcessUnconventional Methods of Sintering Inconel 718 MIM SamplesA Review of Microstructure and Microtexture of Tertiary Oxide Scale in a Hot Strip MillHybrid Calculations of Bending Deformations for 20 Roll Cold Rolling MillInfluence of the Deformation Method on the Microstructure Changes in AZ31 Magnesium Alloy Round Rods Obtained by the Rolling ProcessMicrostructure and Mechanical Properties of Multi-Pass Warm Rolled Ti-6Al-4V Alloy of Different MicrostructuresDeep Drawing of One-Sided, Stiffness Increasing Sheet Metal CompositesEffect of Plastic Deformation on Elastic and Plastic Recovery in CP-TitaniumFabrication of Deep Cup with Flange by In-Plane Stretch Forming Applying Compressive Force in Thickness DirectionFriction Stir Welding of Copper Alloy CuETPHot Stamping of Titanium Alloy Sheets into U Shape with Concave Bottom and Joggle Using Resistance HeatingInfluence of Geometrical Shapes and Sheet Thicknesses on the Dimensional Accuracy of Single and Assembled PartsStability of a Suppression Method of Dent and Spring-Back in Zigzag Bending of Sheet Metal/PlateStudies on the Hot Forming and Cold-Die Quenching of AA6082 Tailor Welded BlanksThe Influence of Strain Rate and Strain on the Behavior of Stress Relaxation in 980 MPa-Grade Dual Phase Steel SheetsEffect of Multistage Deformation during the Pipe Processing on Mechanical Properties of Steels Strength Grade X70-X80Investigation about the Oil Pressure Rate in the Warm Hydroforming of an Al-Mg Alloy ComponentInvestigation on the Mechanical Properties and Formability of Ti3Al2.5V Tubes Deformed at Elevated TemperaturesNumerical and Experimental Study on Sheet Hydroforming of 2A12 Aluminum AlloyProduction Technology for Precision Seamless Steel Tubes from the Perspective of Microhardness ChangesT-Shape Connector Hydroforming Process Analysis