PRICM7

Characterization of Substructure Evolution in Ferrous Lenticular MartensiteCrystallography of Ferrite Nucleation at Austenite Grain Boundary in a Low Carbon Steel Review on the Hall-Petch Relation in Ferritic SteelContinuous Casting of Advanced Steels of Near-Peritectic Composition Towards Radiation Tolerant Nanostructured Ferritic AlloysApplication of Quenching and Partitioning to Improve Ductility of Ultrahigh Strength Low Alloy SteelMicrostructural Evolution during the Novel Quenching and Partitioning (Q&P) Heat Treatment of SteelStudy of a Novel Ultra-High Strength Steel with Adequate Ductility and Toughness by Quenching-Partitioning-Tempering ProcessAdvanced Steel Design by Multi-Scale ModelingA Systematic Study on Iron Carbides from First-PrinciplesThe Effect of Inclusions on Mechanical Behaviour in Ultra-High Strength Alloy SteelsThe Development of Mn-Series Air-Cooled and Water-Quenched Bainitic Steels in ChinaEffect of Nb Content on Hot Flow Stress, Dynamic Recrystallization and Strain Accumulation Behaviors in Low Carbon Bainitic SteelThe Study on the Precipitation and Mechanical Properties of Steel with CopperTopology of Spheroidized PearliteEvolution of Different Recrystallization Textures in Steels Having {111} Rolling TextureEffect of Austenite on Drawing Limit of Ferrite-Austenite Dual Phase WireApplication of Quenching-Partitioning-Tempering Process in Hot Rolled Plate FabricationMicrostructural Evolution of Medium Carbon Steels during the Quenching and Partitioning ProcessCharacterization of Microstructure and Mechanical Properties of a Nb-Microalloyed Steel after Quenching-Partitioning-Tempering ProcessThe Effect of Mn and Si on the Properties of Advanced High Strength Steels Processed by Quenching and PartitioningThe Isothermal Transformation of Low-Alloy Low-C CMnSi Steels below MSNano-Scale Analysis of Nano-Bainite Formed in Advanced High Strength SteelsNitriding of a Nb-Microalloyed Thin Strip Cast Steel at 525?CAn Investigation on Precipitation Behaviour of Cu-Rich Phase in Super304H Heat-Resistant Steel by Three Dimensional Atom ProbeStudy on Carbonitride Precipitating Process in Nb-V Micro-Alloyed Steel650?C Long-Term Structure Stability Study on 18Cr-9Ni-3CuNbN Heat-Resistant Steel
In Situ TEM and APT Analysis on the Dislocations Associated with Solute Carbons in Strain-Aged Low Carbon Pipeline Steels
In Situ Observation of Microstructure Evolution in Low Carbon Bainite Steels Isothermally Held Below A1 TemperatureIsothermal Martensitic Transformation in a Sensitized SUS304 Stainless Steel under Magnetic FieldMicrostructural Observation on Materials of the Japanese Sword under Fold-Forging Process Evidence of Lath Martensite in High-C Japanese Sword Produced from Tamahagane Steel by Tatara ProcessColored Metallography Study of Bainite Steel Used for High Speed Railway CrossingRelationship between Particle Size and Martensitic Transformation in an Fe-30at%Ni AlloySpheroidization Behavior of Cementite in a High Carbon SteelInfluence of Silicon on the Spheroidization of Cementite in Hypereutectoid Bearing SteelsDuctile-to-Brittle Transition Behavior of High-Nitrogen 18Cr-10Mn-0.35N Austenitic Steels Containing Ni and CuRole of Microstructure in Susceptibility of X70 Pipeline Steel to Hydrogen EmbrittlementMicrostructure and Tensile Properties of ODS Ferritic Steels Produced by Mechanical Alloying in Argon and Hydrogen Gas EnvironmentsEffect of Grain Boundary Serration on the Tensile Properties of the Super 304H Heat Resistant Austenitic Stainless SteelTensile Deformation Behavior of Tempered Martensitic Steels Produced in CGL LinesScale-Bridging Analysis of Stress Partitioning in High Nitrogen SteelEffect of Niobium Content on Laminar Precipitate and High Temperature Mechanical Properties of 21-2N Valve SteelEffect of Copper Sulfide on the Fatigue Properties of Bake Hardening Steels Stress Dependence of Microstructural Evolution in Heat Resistant Steels The Effect of Temperature on the Tensile Properties of Steel 0Cr18Ni9Recent Product Developments with Ultra-Thin Cast Strip Products Produced by the CASTRIP? ProcessResearch and Production Practice of DR Material in BaosteelAnalysis of Advanced Strip Shape during Cold Rolling of Thin StripA Pilot Rolling Mill Designed for High Strength SteelsCold Rolling and Annealing Microstructures and Textures of Low Carbon Steels Effects of Deformation Strains and Annealing Temperatures on Mechanical Properties of Martensitic SteelsAnalysis of Edge Crack of Thin Strip during Cold RollingStudy on New Model of Tension Process in Continuous Rolling Study on the Production of Ti Micro-Alloyed High Strength Hot Rolled Steel by CSP ProcessHot Ductility of High Carbon Steel Produced by CSPUltrafine Grained High Strength Low Alloy Steel with High Strength and High DuctilityMechanical Properties of Micro-Alloyed TRIP SteelMechanical Properties of Hypereutectoid Steel with Microduplex (a+?) Structure Formed by Hot Deformation of Undercooled AusteniteHot-Rolled TRIP Steels Based on Dynamic Transformation of Undercooled AusteniteEffect of Thermomechanical Processing Parameters on the Microstructure Development in Low Si TRIP SteelSelective Oxidation and Sub-Surface Phase Transformation during Austenitic Annealing of TWIP SteelsEffect of N on Microstructure and Tensile Behavior of TWIP SteelHot-Working Behaviour of Advanced High-Manganese C-Mn-Si-Al SteelsConstitutive Modeling of TWIP Steel in Uni-Axial TensionDevelopment of a Robust TRIP800 Concept for GI/GA Automotive ApplicationsOn the Stretch-Flangeability of High Mn TWIP SteelsProcessing, Properties and Microstructure of a 1.2%Al TRIP SteelUltra Fine-Grained 6wt% Manganese TRIP SteelEffect of Heat Treatment on Microstructure and Mechanical Properties of Low-Carbon TRIP Steel TubeGrain Size Dependence of the Flow Stress of TWIP SteelEffects of Processing Parameters on Microstructure Development in X70 Pipeline SteelInfluence of Phosphorous and Boron on the Recrystallization, Grain Growth and Mechanical Properties of 3% Si SteelInfluence of Initial Microstructure on Mechanical Properties of Cu Bearing Extra Low Carbon Steel SheetsHot Deformation Behavior of V-Microalloyed SteelInfluence of Strain Path Changes on Microstructure Inhomogeneity and Mechanical Behavior of Wire Drawing ProductsEffects of Alloying Elements on Mechanical Properties in Hyper-Eutectoid Steel WiresEvaluation of Press Formability Using Servo Die Cushion in Deep DrawingAluminide Coating Formation on Hot Press Forming SteelsInfluence of Thermal History on Microstructure and Mechanical Properties of Steels for Hot StampingPhase Transformation and Annealing Behavior of SUS 304 Austenitic Stainless Steel Deformed by High Pressure Torsion Torsion Textures Simulation by Considering Rigid Body RotationSlide-Bend Forming of Very Thin Metal Sheet Using Slide-Ironing ToolA Study on Tool Wear of Sheet Metal Stamping Die Using Numerical Method Back Bead Characteristics during Butt Welding of a Thick Plate for Various Backing ConditionsWelding Technology of Ultra-Low Carbon and Nitrogen Ferrite Stainless SteelThe Oxide Inclusion and Heat-Affected-Zone Toughness of Low Carbon Steels Preliminary Investigation into Repair of High Strength Steel Using Laser Cladding Unconventional Short-Term Glow Discharge Nitriding of 316L Austenitic Steel Effect of Carbon on Frictional Wear Behaviours of High Vanadium High Speed Steel under Dry Sliding ConditionEffect of Microshot Peening on Surface Characteristics of Spring SteelMechanical Properties and Marine Corrosion Resistance of P-Bearing ULCB SteelsCompatibility Evaluation for Application of Lean Duplex Stainless Steels to Seawater Systems in Nuclear Power PlantsInfluence of Cu Contents in Hot Shortness of Cu Bearing EAF SteelsInterfacial Properties Prediction of Liquid Iron-Si Inclusion-MgO Refractory Mold Thermocouple Locations and their Impact on Prevention of Caster BreakoutsMaterials Technology for PC-TPP in Green Economic EraThe Fabrication of Titanium Aluminide Matrix Composite Sheet by Rolling and Reaction AnnealingWelding Soundness of a Thick-Walled 9Cr-1Mo SteelFundamentals of Spark-Plasma Sintering: Applications to Net-Shaping of High Strength Temperature Resistant ComponentsConstruction of a High Temperature Grade 91 Sodium Component Test LoopMo Effect on the Microstructure in Co-Al-W-Based SuperalloysHigh Temperature Strength of Ir/Ir2Y Two Phase Alloys in the Ir-Pt-Y System Grain Refinement and Nuclei Formation Mechanism of Ni-Based Superalloy K417 with Low Voltage Pulsed Magnetic CastingThe Effect of Ti Addition on Phase Equilibria among Ni (A1), Ni3Al (L12) and Ni3V (D022) PhasesMicrostructural Characterization of Nb-Al Base ODS AlloysAlloying Behavior of Ni3Nb, Ni3V and Ni3Ti CompoundsAlloy Design of Nb-Si Based High Temperature Alloys by Phase Stability ControlThe Stability of ? ?-Co3(Al,W) Phase in Co-Al-W Ternary SystemThe Effect of Alloying Elements on Microstructure and Strength Property of Dual Two-Phase Intermetallic Alloys Based on Ni3Al-Ni3V Pseudo-Binary Alloy SystemPhase Transition and Ordering Temperatures of TiAl-Mo Alloys Investigated by In Situ Diffraction ExperimentsEffect of Y on Microstructure and Mechanical Properties of a Ti Alloy Effects of Electropulsing Treatment on the Precipitation Behaviour of Grain Boundary Carbides in GH3044 AlloyProperty Responses in Nb-Si-Hf-Ti-Al-W-B-Cr Alloys for High-Temperature ApplicationsThe Effect of Refractory Elements on Microstructure and Mechanical Properties of Ni3(Si,Ti) Intermetallic AlloysMicrostructure and High Temperature Strength in Fe3Al Base Alloys Containing Fine Carbide Particles Microstructure and Mechanical Properties of Al Added Ni3(Si,Ti) Intermetallic Thin SheetsThe Effect of Grain Size on Cutting Force in End Milling of Inconel 718CThe Potential of HAZ Property Improvement through Control of Grain Boundary Character in a Wrought Ni-Based SuperalloyPhase-Field Simulation on Phase Transformation during Creep Deformation in Type 304 SteelThe Role of Interfacial Precipitates on Creep Behaviour of Power Metallurgy (PM) Ti-48Al-2Cr-2Nb+1W AlloyThe Effect of Heat Treatments on Microstructure and Creep Properties of Powder Metallurgy Beta Gamma Titanium Aluminide AlloysCreep Behaviour and Microstructural Changes of Advanced Creep Resistant Steels after Long-Term Isothermal AgeingCreep Behavior for Alloy 617 in Air at 950?C Microstructure and Creep Behavior of a Single Crystal Nickel-Base Superalloy with [011] OrientationStatistical Analysis of Creep Crack Growth Behavior in Modified 9Cr-1Mo SteelEffects of Ferrite Content on the Tensile Strength and Impact Toughness of 2.25Cr-1Mo-0.25V SteelsCreep Crack Growth Rates on the Base and Welded Metals of Modified 9Cr-1Mo SteelEvaluation of Creep-Fatigue Crack Growth for Grade 91 Steel Wide PlateFretting Wear Resistance of ATW Cr3C2/Ni3Al Composite Hardfacing on IC6SXIsothermal Oxidation Behavior of a New Directionally Solidified Ni-Base Superalloy in Air at Different Temperature High Temperature Oxidation Behavior of Si-Mo Ferritic Ductile Cast IronFormation of Protective Intermediate Phase in Ta Addition TiAl during High Temperature OxidationCobalt-Based Alloys for High Temperature ApplicationsStudy of a New Type High Strength Ni-Based Superalloy DZ468 with Good Hot Corrosion ResistanceOxidation Resistance of Innovative Carbon-Based Materials Results of ExtreMatOxidation of TiAl Alloys Coated by Fluorine Resin in SO2 Containing AtmosphereHigh-Temperature Sulfurization of Crofer 22APU in H2/H2S AtmosphereHigh Temperature Alloys from Nb-Cr-Si System with Minor AdditionsThixomolded? and Thermomechanically Processed Fine-Grained Magnesium AlloysDevelopment of the Microstructure and Texture of RE Containing Magnesium Alloys during Hot RollingResearch on High Strength and High Toughness Titanium Alloy with Damage TolerancePrecipitation Sequence in an Al-Si-Mg Foundry AlloyMicrostructure and Joint Strength of Similar- and Dissimilar Lap Joints Fabricated by Several Advanced Solid-State Welding Methods Building Capability through Benchmarking and Technology TransferTemperature Dependence of Compressive Deformation Behavior of Mg89Zn4Y7 Extruded LPSO-Phase AlloysThermal Stability and Mechanical Properties of Extruded Mg-Zn-Y Alloys with Long-Period Stacking Order PhaseMultimodal Microstructure Evolution in Wrought Mg-Zn-Y Alloys with High Strength and Increased DuctilityPreparation and Mechanical Property of Mg-Zn-Y Alloy with a Long Period Ordered PhaseFormation of a Novel X Phase in Mg?Gd?Zn?Zr AlloyTEM Observation of Precipitates in a Mg-Gd-Sc Alloy with High Content of ScEffect of Sc Addition on Aging Behavior of Mg-Gd AlloysEffect of Minor Additions of Al and Si on the Mechanical Properties of Cast Mg-3Sn-2Ca Alloys in Low Temperature RangeMicrostructure and Tensile Properties of an Mg-5Sn-5Zn AlloyMicrostructures and Mechanical Properties of Mg-9Zn-Zr Magnesium AlloysEffect of Bi Addition on Thermal Stability and Tensile Ductility of Mg-3%Zn-0.4%Zr AlloyStudy on Mechanical Properties and Microstructures of Mg-6Zn-2Gd-0.6Zr New Sand-Casting Magnesium AlloyEffects of Trace Cu Addition on the Microstructure and Tensile Properties of ZK60 AlloyEffect of Quenching on Aging Behavior of Binary Mg-Zn AlloysEffect of Casting Method and Al Contents on Microstructure in AM-Type Magnesium AlloysMicrostructural Evolution of Rheo-Diecast AZ91D Magnesium Alloy with Gadolinium AdditionInoculation during Metal Castings: Beyond Grain RefiningAluminium-Rich Coring Structures in Mg-Al Alloys with Carbon InoculationMicrostructure and Aging Behavior in AM60 Magnesium Alloy Cast into Sand and Permanent MoldsThe Influence of Eutectic Morphology on the Impact Properties of High Pressure Die Cast Mg-Rare-Earth AlloysDevelopment of Heat-Resistance and Creep-Resistance Magnesium Alloy of Die-Casting Mg-4Al-4La and/or CeThe Skin Effect in an Mg-RE High Pressure Die Cast AlloyInfluence of Grain Boundary on Activation of Slip Systems in Magnesium: Crystal Plasticity AnalysisDeformation Behavior of Magnesium Single Crystal in c-Axis Compression and a-Axis TensionMicrostructure and Mechanical Properties of Extruded Mg-Zn-Ca AlloyTwinning-Induced Negative Strain Rate Sensitivity in Wrought Magnesium Alloy AZ31Grain Refinement of Magnesium Alloy AZ31 under Torsion Extrusion with a Square-Hole DieTwinning Behavior in AZ31-B Polycrystal Texture Subjected to In-Situ Bending TestTexture and Mechanical Properties of AZ31 Magnesium Alloy Sheets Processed by Symmetric/Asymmetric Combination Hot-RollingCrystallographic Orientation Dependence of Fatigue Crack Propagation Behavior in Rolled AZ31 Magnesium AlloyMicrostructure Evolution in AZ31 Magnesium Alloy Worked by Torsion at Warm TemperatureDeep Drawing of AM31 Magnesium AlloysGrain Refinement by Combined ECAE/Extrusion and Dieless Drawing Processes for AZ31 Magnesium Alloy TubesWarm Hydroforming Process with Non-Uniform Heating for AZ31 Magnesium Alloy TubeSound Insulation Study on Mg Sheet and Mg Honeycomb PanelsEffect of Temperature on Plastic Buckling Strength of Shot Peened Pipe of Magnesium AlloysMicrostructural Evolution during Friction Stir Processing of Magnesium Alloy CastingsWelding Interface in Magnetic Pulse Welded JointsMicrostructure of Laser Treated ZE41A-T5 Magnesium AlloySurface Modification and Repair for Aircraft Life Enhancement and Structural RestorationImprovement of Corrosion Resistance of Extruded Mg-Zn-Y Mg/LPSO Two-Phase Alloys by Fourth Element AdditionMechanical Properties and Microstructure of AZ Magnesium Alloys Anodized by Phosphate ElectrolyteCharacterization of Nickel Oxide Layers on the AZ91 Mg Alloys by Plasma Electrolytic OxidationThe Effect of Cd Addition on NDE of As-Cast Mg-Cd Alloy in 0.1M NaCl SolutionModelling of the Metal/Mould Interactions in the DC Casting Process for Aluminium and MagnesiumContinuous Casting of Magnesium Alloy Billet Using Electromagnetic TechniquesThermal Analysis of a Bi-Metallic Chill Vent for High Pressure Die CastingIn-Line Rolling of Aluminum Alloy Strip Cast by a High Speed Twin Roll CasterTechnology of Molten Salt Electrolysis of Magnesium ChlorideLCA Study of Rare Earth Metals for Magnesium Alloy ApplicationsProduction of Ti-6Al-4V Strip by Direct Rolling of Blended Elemental PowderEffects of Impurity Elements on Green Strength of Powder CompactsMechanical Properties of Oxide Dispersion Strengthened Pure Titanium Produced by Powder Metallurgy MethodSpark Plasma Sintering of Ti-4.5Al-3V-2Fe-2Mo (SP-700)Microstructural Evolution in Chips during Machining of Commercially Pure (Grade 2) TitaniumEffect of Pore Size on Mechanical Properties of Titanium FoamsEffect of Hydrogen Content on Superplastic Forming and Diffusion Bonding in Ti600 AlloyImprovement in Hot Workability of Titanium Matrix Composite by Thermohydrogen TreatmentStudy of Thermal Behavior in a Kroll Reactor for the Optimization of Ti Sponge ProductionThe Ageing Behavior of Titanium Alloy Ti-10V-2Fe-3Al The Effect of Temperature on the Microstructure of a Metastable ? Ti AlloyEffect of Aging Treatment on Microstructure and Mechanical Properties of a Two-Phase Titanium AlloyPhase Constitution and Heat Treatment Behavior of Ti-7mass% Mn-Al Alloys Aging Response of TB-13 Titanium AlloyRecent Developments in Mechanisms and the Kinetics of Deformation Twinning in Titanium AlloysElectron Microscopy Study of Deformation Microstructure in Metastable ? Titanium AlloyInfluence of Heat Treatment on the Pseudoelastic Behaviour of a ? Ti-25Nb-3Zr-3Mo-2Sn AlloyPlastic Deformation Characteristics and Evaluation of Press Formability for Ti-6Al-4V Sheet at Warm Temperature Modelling the High Temperature Deformation of Ti-6Al-4VStudy on Tensile Property and Fracture of Welded Joint of Ti-6.5Al-2Zr-1Mo-1V Alloy by Hydrogen ProcessingAssessment of Durability and Damage Tolerance of ?-Annealed Ti-6Al-4VCharacterization of the Mechanical Behaviour of Both Fusion Zone and Base Metal of Electron Beam Welded TA6V Titanium Alloy3D Transient Thermal Modelling and Experimental Validation of the Temperature Distribution during Laser Heating of Ti6Al4V AlloyCharacterisation of Cold Spray Titanium CoatingsDrawability of Ti-6Al-4V Sheet at Elevated TemperaturesScrew Form Rolling of Beta Type Titanium Alloy Preliminary Worked by TorsionMicrostructural Characteristics of Electron Beam Processed Al-2ScQuantitative Analysis of Precipitate Compositions in an Al-Li-Mg-Cu Alloy Using Atom Probe TomographyEffect of Pre-Ageing on the Artificial Ageing Response of Al-Mg-Si(-Cu) AlloysEffect of Applied Stress on Nucleation and Growth of Precipitates in a Cu-Be-Co AlloyDispersoid Phases in 6xxx Series Aluminium AlloysTEM Observation of Metastable Phases in Aged Al-Mg-Ge AlloysInfluence of Solution Treatment on Microstructure and Quench Cracking in a Water-Quenched Aluminium Alloy 7150Low-Cycle Fatigue Behavior of an Al-Mg-Si Alloy with and without a Small Addition of ScSolute Segregation at S11(113)[110] Grain Boundary and Effect of the Segregation on Grain Boundary Cohesion in Aluminum from First PrinciplesUnderstanding the Directional Dependence of Intergranular Corrosion in Aluminium AlloysExperimental Investigation of the Dynamic Behavior of Aluminum FoamsAlloy Design for Enhancing the Fracture Resistance of Heat Treated High Pressure Die-CastingsRefinement of TiB2 in Al-Ti-B Grain Refiner Alloys by Ultrasound and the Effect on Al Grain SizeMicrostructural Evolution in Various Regions of Stir Zone during Friction Stir Processing of Al-7Si-0.3Mg Cast AlloyApplication of Laser Remote Welding to an Aluminum Automotive PartJoint Interface Morphology of Friction Stir Spot Welded Aluminum Alloy Sheets and Plated Steel SheetsMorphological Variation of Fe/Cr-Rich Intermetallic Phase in Recycled Al-Si Alloy as a Function of Solidification Rate: Time-Resolved RadiographyRoll Casting of Al-SiCp StripEffect of Electromagnetic Field on Horizontal Direct Chill Casting of 7075 Aluminum AlloyThe Microstructure Characteristics and Wear Resistance of Rapidly Solidified Hypereutectic Al-Si AlloysUntrasonic-Assisted Fabrication of SiC Nanoparticles Reinforced Aluminum Matrix CompositesSolidification Structure and Sound Absorbability of A356 Alloy FoamsEffect of Rapid Solidification Processing on Hydrogen Behaviour in AluminiumMicrostructure and Corrosion Behavior in Al-Mg Based Alloys Subjected to Continuous Cyclic Bending and Annealing Dynamic Deformation of Submicrocrystalline Aluminum AlloysEffect of Zr Addition on Microstructure and Warm Formability of Al-Mg Sheet AlloysAdiabatic Shear Banding in an Al-Mg-Si Alloy Processed by Equal Channel Angular PressingTexture Distribution through Thickness in 6xxx Aluminum Alloy Sheet Fabricated by Cross-Roll Rolling MethodAssessing of Bendability of Aluminum Alloy Sheets for AutobodiesDurability of Aluminum Alloy/Rubber Joints in Corrosive EnvironmentStructure of Porous Copper Fabricated by Unidirectional Solidification under Pressurized HydrogenStructural Behavior of FRP Lighting Pole SystemLocal Atomic Arrangements of Pd-Based Bulk Metallic Glasses of the Metal-Metalloid Type Demonstrated by Molecular Dynamics SimulationsHigh Glass-Forming Ability and Unusual Deformation Behavior of New Zr-Cu-Fe-Al Bulk Metallic GlassesViscous Flow Behaviour of Supercooled Liquids and Mechanical Properties in Zr-Cu-Ni-Al Bulk Metallic GlassesEffect of Residual Stress on Mechanical Property of Monolithic Bulk Metallic GlassMicrostructural Assessment of the Oxidation Behavior of Cu-Based Metallic Glass PowderMechanical Properties and Structures of High Entropy Alloys and Bulk Metallic Glasses CompositesBulk Metallic Glass Formation, Crystallization, and Magnetic Properties of RE4Fe72B22M2 AlloysCharacteristics of Ti-Ni-Zr Thin Film Metallic Glasses Exhibiting a Shape Memory Effect after CrystallizationRelaxation Behavior of Zr-Cu-Al Ternary Bulk Glassy Alloy Studied by Using Positron Annihilation TechniquesInfluence of Solidification Speed on Quality and Quantity of Structural Defects in Fe61Co10Zr2.5Hf2.5Y2W2B20 Amorphous AlloyAmorphous Magnesium Sheet Produced by Twin Roll CastingDevitrification Studies of Mg60Cu29Gd11 Bulk Metallic GlasConsolidation Behavior of Cu-Zr-Al Metallic Glass Powder by Spark Plasma SinteringFormation of Amorphous Fe-Cr-P-C Alloy Coating Films by a Newly Developed Thermal Spraying TechniqueLow Temperature Synthesis of Silicon Nanocrystals Fabricated by PECVD and their Optical PropertyFePBNbCr Soft Magnetic Glassy Alloys ?SENNTIX? with Low Loss Characteristics for Commercial Inductor CoresHigh Bs FeSiBPCu Nanocrystalline Wide Ribbons Using Industrial Raw MaterialsEffect of Nitridation Magnetic Properties of Nanocrystalline Fe-Co Alloy PowdersMechanical and Physical Properties of Nano-MetalsTensile Properties of Bulk Nanocrystalline Ni and Ni-W Fabricated by Sulfamate BathHigh Strength and High Ductility in Electrodeposited Nanocrystalline Ni?W AlloyProcessing and Excellent Oxidation Resistance of Nanocrystalline Fe-Cr AlloysControlled Growth of 1-D Nanomaterials Base on Electro-Deposited Nanocrystalline Films: A OverviewNanocrystalline Phosphors for Lighting and Detection ApplicationsEffect of Sol-Gel Synthesis on the Structural and Photoluminescence Properties of Magnetoplumbite-Type Strontium FerriteCombined Field and Thermionic Emission Process in ZnO Nanostructure Cold Emission CathodeSynthesis and Characterization of CdSe Microspheres via Solvothermal ProcessPreparation and Characterization of BNC Compounds with Cylindrical and Bamboo NanotubesInvestigation on the Plasma-Induced Electron Emission Properties of ZnO Nanorod and Carbon Nanotube ArraysThe Characterization and Gas Sensing Properties of Polythiophene Coated V2O5 NanotubesCurrent Steps in Poly(3-Hexylthiophene)/ZnO Nanobelt Hybrid DiodesMechanical Properties of Electrodeposited Ni-SiO2 NanocompositeModelling the Crystallization Reactions of Amorphous Precursors in Fe3B/Nd2Fe14B Nanocomposite MagnetsNew Crystallographic Textures of Nd2Fe14B/a-Fe Nanocomposite Materials Prepared by Controlled Melt SpinningEffect of Organic Capping on the Magnetic Properties of Au NanoparticlesThe Electrical Characterization of Single ZnO Nanowries Field-Effect TransistorsPreparation of Photoluminescent Silicon Nanowires Based on Multicrystalline Silicon Wafers Shape-Controlled Synthesis and Formation Mechanism of Cobalt Nanopowders by a PVP-Assisted MethodAtomic-Scale-Deformation-Dynamics (ASDS) of Nanowires and NanofilmsMicrostructure and Texture Evolution during Friction Stir Processing of AZ31 Mg AlloyNanostructure Formation during Deep Wire-Drawing of CopperWork-Softening, High Pressure Phase Formation and Powder Consolidation by HPTThe Influence of Processing Conditions on Hardness Homogeneity Evolution in Commercially Pure Cast Aluminium Processed by ECAPGrain Refinement and Texture Evolution during Equal Channel Angular Extrusion of Pure Cu and Cu-Zn AlloysEnhancing Ductility of ECAP Processed MetalsUltrafine Grained Structure Formation in Low Carbon Steel Processed by SPDEffects of Phase Transformation Temperature on Formation of Wear-Induced Layer in Fe-Ni AlloysFormation of Deformation Twins and Related Shear Bands in Copper Single Crystals Pressed by ECAPSusceptibility to Hydrogen Embrittlement of IF Steel with Ultrafine-Grained Structure Produced by Accumulative Roll-Bonding ProcessHigh Strength and Ductility in Ball-Milled Titanium Powders Consolidated by High-Pressure TorsionAging Behavior of Al-Li-Cu-Mg Alloy Processed by High-Pressure Torsion Visualization and Quantification of Severe Internal Deformation on Compressive Torsion ProcessDeformation Characteristics in AlphaType Brass Worked by TorsionStructure and Mechanical Properties of Asymmetrically Rolled IF Steel SheetTexture Change of Severe Plastically Deformed Al Alloy SheetsSteel-Magnesium Composite Wire Obtained by Repeated Co-ExtrusionMechanisms of Dynamic Recrystallization in Cu-Sn-P AlloyDynamic Recrystallization Behaviour in Cu-Sn-P Alloy for High Strength Copper TubeDynamic Recrystallization Behavior of Biomedical CCM Alloys in Hot Compression ProcessTexture and Substructure Development during Post-Dynamic Softening in Ni-30%Fe AusteniteEvaluation of Plastic Work Density, Strain Energy and Slip Multiplication Intensity at Some Typical Grain Boundary Triple JunctionsCyclic Softening of Cu-Ni-Si Alloy Single Crystals under Low-Cycle FatiguePrecipitates Behavior during Thermomechanical Processing of Low Mn, Ti Added Pipeline SteelsNumerical Simulation for Effects of Friction on Deformation Behaviors in a 3-Dimensional Hot Upsetting ProcessThe Effect of Oxygen on the Brittle-to-Ductile Transition in Silicon Single CrystalsEffect of Si Content on Fracture Behaviour Change by Strain Rate in Si SteelsFormability of Pure Titanium Long-Cup by Multi-Stage Deep DrawingInfluence of Roll Speed Schedule on Transverse Wall Thickness Evenness of Shell Elongated by Mandrel MillEffect of Prior Cold-Working on Strength and Electrical Conductivity of Cu-Ti Dilute Alloy Aged in a Hydrogen AtmosphereSimultaneous Enhancement of Electrical Conductivities and Mechanical Properties in Cu-Ti Alloy by Hydrogenation ProcessDevelopment of High Strength and High Conductivity Cu-Ag-Zr AlloyCold Joining of Dissimilar Metal Sheets by Shot PeeningStudy on Powder Metallurgical Preparation of NiCoMnIn Alloy FoamOptimization of the Cooling Process of a Heavy Hydraulic Turbine Runner Band Casting in Heat TreatmentHeterogeneous Nucleation and Grain Formation on Spherical and Flat SubstratesResearches on the Nucleation Behaviors of NH4Cl Crystal on Coarse Aluminum SurfacesDirectional Solidification and Characterization of Al2O3/Er3Al5O12 Eutectic In Situ Composite by Laser Zone RemeltingMicrostructure Evolution and Compression Properties of a Directionally Solidified Ni-24.8%Nb Hypereutectic AlloyThe Contribution of Diffusion Coefficient to the Eutectic Instability and Amorphous Phase FormationAnalysis of an Equiaxed Dendrite Growth Model with Comparisons to In-Situ Results of Equiaxed Dendritic Growth in an Al-Ge AlloyModelling and Experiments Concerning Dendrite Re-Melting and Its Role in Microstructural Evolution in Spray Formed Ni SuperalloysThe Influence of External Mechanical Stresses on Agglomeration and Bending of Solidifying CrystalsUndercooling Behavior and Solidification Microstructure Evolution of Sn-Cu-Ni Solders Modified by Minute Amount of Mixed Rare Earth La-CeStrength and Conductivity of Deformed Cu-Fe Composites after Solidified with a Horizontal Magnetic FieldSolidification Mechanisms in the Sn-Cu-Ni Lead-Free Solder SystemThe Correlation between the Liquid Structure and the Solidification Microstructure of Sn-Cu Lead-Free SoldersEffect of Polygonal Rotor Process on Solidification Structure of Lead-Free Bismuth BronzeNon-Equilibrium Solidification in Cu-Mg-Sn Alloys for Tribological ApplicationsFormation of Primary Intermetallic Compounds in Sn-Ag-Cu AlloysElectromagnetic Continuous Casting Process for Near Net Shape Aluminum Alloy Billet Monte Carlo Simulation of Thermophysical Properties for Al-Ce Liquid AlloysSemisolid Sinter-Forging of Hyper-Eutectic Al-Si Alloy Using Rapid Resistance HeatingThe Character of Melt of A357 Alloy and Its Influences on the Solidification MicrostructuresImproving the Microstructures and Mechanical Properties of Hypereutectic Al-Si Alloys by Spray Forming TechniqueMechanical Properties and Microstructure of Aluminum Alloy Al-6061 Obtained by the Liquid Forging ProcessEffect of Various Processing Route on Microstructure and Mechanical Properties of Spray-Deposited Al-8.6Zn-2.6Mg-2.2Cu AlloyMicrostructure and Mechanical Properties of a Friction Stir Processed Al-Zn-Mg-Cu AlloyApplication of a Criterion for Cold Cracking to Casting High Strength Aluminium AlloysObservation of Hot Tear Formation by Acceleration SensorMechanical Properties and Metallurgical Qualities of High Aluminum Content Magnesium Alloys Fabricated by Twin-Roll CastingGrain Refinement Performance of Al Cast Using Machining ChipsThe Effect of Cu on the Microstructure and the Elevated Temperature Properties of Ferritic Heat Resistant Cast IronFabrication of Porous Metals with Directional Pores through Unidirectional Solidification of Gas-Dissolved MeltThe Effect of Constricting the Melt Flow on Mechanical Properties of High Pressure Die CastingsDevelopment of a Magnesium Alloy Rotor with a Pin-Point Gate MoldEffect of Rare-Earth Elements on the Ignition-Proof Behavior of Industrial Pure MagnesiumProduction Magnesium Alloy Strip with Boss and Rib Section by Melt Drag Process and Experimental ConditionsEffect of Oxygen on the ?-Grain Size of Cast TitaniumSolving Complex Thermal and Mass Transport Problems with the Lattice Monte Carlo MethodNumerical Simulation of Grain Selection Behavior of Single Crystal Ni3Al Based Superalloy CastingMonte-Carlo Modeling of Recrystallization Kinetics of Cold-Rolled TitaniumNumerical Simulation on Semi-Solid Metal Slurry Preparation by A-EMSApplication of Continuous Displacement Cluster Variation Method to Study Phase EquilibriaNumerical Characterization of Anisotropic Heat Sink CompositesPhase Field Simulation of Ni4Ti3 Precipitation in Porous NiTi Shape Memory Alloys under Applied StressesThe Identification of Phase by Overlapping of First Derivative of Dilatation in Low Carbon Steels Multi-Phase PresentingA Monte Carlo Simulation of Melting in Prototype CrystalThree-Dimensional Modeling and Simulation of Dendrite Morphology of Cast Mg AlloysA New Algorithm of Phase Field Approach to Polycrystalline Dendritic Solidification in Two and Three DimensionsPhase Field Modelling of Dendrite Fragmentation during Thermal ShockA Cellular Automaton Model with the Lower Mesh-Induced Anisotropy for Dendritic Solidification of Pure SubstanceHomogenisation of Cast Microstructures: Thermodynamic Calculation and Kinetic SimulationModeling of Microstructure Development in a Continuously Solidified Immiscible AlloyThermal Modeling of Direct Digital Melt-Deposition ProcessesPhysical and Numerical Simulation of Flow and Temperature in Molten Pool during Strip Casting ProcessNumerical Simulation of Bubbles Expansion and Solidification of Metal FoamsPhysical Model of Aluminium Refining Process in the Batch and Continuous ReactorsModeling Study of the Influence of Subflux Controller of Turbulence on the Molten Steel Flow in TundishOptimum Pass Design of Bar Rolling for Producing Bulk Ultrafine-Grained Steel by Numerical SimulationNumerical Simulation of Deformation during Hot Procedure for Large Hydraulic Turbine Runner BladeGrain Fragmentation in Equal Channel Angular Pressed CopperFinite Element Analysis of Multi-Pass Equal Channel Angular Extrusion/Pressing ProcessStatistics for Quantifying the Mechanical Properties of NanomaterialsMolecular Dynamics Based Observations of Grain Boundaries and Lattice Defects Functions in Fine Grained MetalAnalysis of {10-12} Twin Structure by Molecular Dynamics MethodEffect of Micro-Elasticity on Grain Growth and Texture Evolution: A Phase Field StudyAdvanced Material-Technological Modelling of Complex Dynamic Thermomechanical ProcessesA Multi-Scale Constitutive Model in High Temperature Deformation of Near Alpha Ti-5.6Al-4.8Sn-2.0Zr AlloyStudy on Casting Roll during Twin-Roll Casting of Thin StripCrystal Plasticity Finite Element Modelling of the Influence of Friction on Surface Roughening during Uniaxial Planar CompressionRigid-Plastic Finite Element Analysis of Cross Wedge RollingResearch on Design Method of Polygonal Roll Pass for Stretch Reduced Seamless TubesEffects of Forging Processing Parameters on Axial Effective Strain in Heavy ForgingsThe Material Flow Analysis in the Modified Orbital Forging TechnologyResearch on Winding Technology of Thin Helical Tube of Pd-Y AlloyNumerical Simulation on Adiabatic Shearing Behavior of Vanadium Alloy V-5Cr-5Ti Hat-Shaped SpecimenAdvances on Modelling of the Tool/Workpiece Interface during High Shear Processing Effects of Hub Contact Shape on Contact Pressure and Fatigue Life in a Press-Fitted ShaftResidual Stresses in Cold Spray Process Using Finite Element AnalysisThermal-Structural Finite Element Analysis of Injection Moulding Dies with Optimized Cooling ChannelsModeling Corrosion of a Metal under an Aerosol DropletDetermination of Interphase Thickness and Mechanical Properties of Effective Nanofillers in Polymer Nanocomposites by Molecular Dynamic SimulationTheoretical Study of Growth Mechanism of Goethite in the Presence of SurfactantsFirst-Principles Calculation of Water Molecules with Adsorbed Ions on the Fe(001) SurfaceFirst-Principles Calculations of C2H4 Adsorption on Pd Surface Stacked on Fcc-AuMechanical Properties and Size Effects of ZnO Nanowires Studied by First-Principles CalculationFirst-Principles Study of Formation and Properties of Fcc-NdOx in Nd-Fe-B Sintered MagnetsFirst-Principles Investigation of the Electronic Structure and Magnetic Properties for Co-Doped Fe3O4Simulation of Dislocation Accumulation in ULSI Cells of Reduced Gate LengthMicrostructure of a Paint Primer - a Data-Constrained Modeling AnalysisThe Effect of the Doping Profile in Aluminum Back-Surface-Field on the Electronic Properties of c-Si Solar CellsApplication of High Power DC Arc Plasma for Mass Production of High Quality Freestanding Diamond Films and Diamond Film Coated Cutting ToolsCrater Eruption Induced by High Current Pulsed Electron Beam (HCPEB) TreatmentConstrains of Super-Current Flow in YBCO Coated ConductorsStudy of Deposition of Aluminum Nitride Thin Films by Hollow Cathode Electron Beam Vapor Deposition MethodSynthesis and Its Characteristic of Silicon Nitride Film Deposited by ECR-PECVD at Low TemperatureEffect of Nitridation on GaN Film Grown on Glass Substrate by ECR-PEMOCVD MethodResearch on Influence of Ion-Assisted Deposition to the Optical and Mechanical Properties of SiO2 Film Fabrication of Numerous Ferromagnetic Metal Nanowires Using Electrodeposition TechniqueFabrication of Co/Cu Multilayered Nanowires Using a Pulsed Current Deposition TechniqueElectrodeposition of ZnTe Compound Semiconductors from Aqueous SolutionThe Effect of Cobalt Addition on Structural and Magnetic Properties of Electrodeposited Iron-Platinum Nanocrystalline Thin FilmsDeposition of GaN Films on Freestanding CVD Thick Diamond FilmsThe Preparation for Cu(Sn) Films of Barrierless InterconnectionThe Effects of Substrate Temperature on the Composition and IR Transmission Properties of Germanium Carbon Films Deposited by Reactive RF Magnetron SputteringTechnological Parameters and Electrical Properties of Ti/TiN Multilayer Films Prepared by Magnetron SputteringInvestigation on the Mechanical Properties of Molybdenum-Doped Zinc Oxide Transparent Thin Film by Sputtering TechniquePreparation and Characterization on Cellulose Nanofiber FilmEffect of Iodine Doping on Surface and Optical Properties of Polyterpenol Thin FilmsTriangular Dislocation Loop Model for Surface Displacement in Indented Thin FilmsStructural Stabilities in GaAs Nanocrystals Grown on Si (111) SurfaceEffect of Ultra-Thin Pt Layer on the Preferred Orientation of AlN FilmsSynthetic Properties of the c-Axis Tilted AlN Thin FilmsEnhancement of Photocatalytic Reaction of Titanium Dioxide Film by Surface TexturingGrowth and Characterization of Ge1-xSnx Layers for High Mobility Tensile-Strained Ge Channels of CMOS DevicesThe Optimization of SMR-Based Filter by Thermal Annealing TreatmentEffect of Interlayer Thickness on Stress and Dielectric Properties of MgTiO3 Modified (Ba,Sr)TiO3 Multilayer Thin FilmsDirect Measurement for Electric Resistance of Ferromagnetic Metal- Nano-Contact in Oxide Layer Surface Treatment of 316L Stainless Steel by High Current Pulsed Electron Beam Numerical Simulation for Surface Modification of Thermal Barrier Coatings by High-Current Pulse Electron BeamEffect of Pre-Deforming on Plasma Nitriding Response of 304 Stainless SteelThe Addition of Silica Nanoparticles with Different Sizes for a Silica Film on Stainless Steel without Crack FormationDevelopment of Infrared Ray Curing Technology at Continuous Coil Coating LinePEM Fuel Cell Separator with Thermally Nitrided Low Carbon SteelThermal Barrier Systems and Multi-Layered Coatings Fabricated by Spark Plasma Sintering for the Protection of Ni-Base SuperalloysElectrochemical Characteristics of Sintered Duplex Ferritic-Austenitic Stainless Steels Produced by Powder Metallurgy ProcessMultilayered Approach to Step-Edge Josephson JunctionsDeposition of Superconducting Thin Films of Magnesium Di-Boride on Various Substrates by Electroless Plating ProcessRaman Scattering Studies in Oxygen-Vacancy Induced Ferromagnetism of Co-Doped ZnO FilmsCharacterization Performance of Laser Melted Commercial Tool SteelsFundamental Property of Metals ? Grain Boundaries Phase Transition as a Basis of Nanostructured Layers, Materials and Composites Production
In Situ TiB2 Particles Reinforced Copper Matrix Composite Coating on Mould Steel by Laser CladdingDetermination of Mechanical Properties of TiN Coating Using a Notched Cylindrical Stainless Steel SubstrateLiquid Phase Separation Behaviors in Cu-Fe Alloy Coatings Synthesized by Laser CladdingMicrostructure and Wear Behaviour of Laser Induced In-Situ Formation of TiBx and TiC Titanium Composite CoatingsComposition Design and Laser Cladding of Cu-Zr-Al Alloy Coating on the Magnesium AlloyEffect of Titania Nanoparticles on Micro-Arc Anodizing of AM60B Magnesium AlloyStructure and Properties of Cold Spray CoatingsAluminizing of TiAl-Based Alloy Using Thermal Spray CoatingProduction of Stainless Cast Iron Base Deposits with Dispersed Titanium Carbide Particles by Plasma SprayingEffect of Ultrasonic Surface Peening on Fatigue Property of 7B04 High Strength and Toughness Aluminum AlloyMulti-Layer Coating for Optical Mold of Strengthening by Electroplating Ni-W and Electroless Plating Ni-Mo-P by Nonisothermal MethodInvestigation of Super-Hydrophobic Coatings with Hierarchical Structures Surface on Mild SteelElectrochromic Properties of Nano-Columnar Nickel OxidePreparation and Property of a Fe-Doped DLC Multilayer by Ion SourcesElectrodeposition of CuSn Alloy from Noncyanide Sulfosuccinate BathDevelopment of a Processing Window for the Transformation Hardening of Nickel-Aluminium-BronzeThe Investigation of the Interdiffusion Barrier in TiAl/MCrAlY SystemEffect of Pre-Oxidation Treatment on the Thermal Shock Resistance of Thermal Barrier Coatings in a Combustion Gas EnvironmentInvestigation on Interfacial Bonding Strength of Anisotropic Conducive Adhesive with a New Cohesive Zone ModelThe Effects of Heat Treatment on the Bonding Strength of Surface-Activated Bonding (SAB)-Treated Copper-Nickel Fine Clad MetalsInvestigation on Oxidation Resistance of NiCoCrAlY Coating Irradiated by High Current Pulsed Electron BeamInfluence of Cryomilling on Microstructure, Phase Stability and Oxidation Behavior of NiCrAlY Bond Coat in Thermal Barrier Coatings: Experimentation and Mechanistic InvestigationHot Corrosion Behavior of a Novel Enamel-Based Thermal Barrier CoatingHigh Temperature Corrosion of Fe-Cr, Fe-Al, Fe-Si and Fe-Si-Al Alloys in CO2-H2O GasesCorrosion and Oxidation Protection of Ti6Al4V Alloy by an Inorganic Metal Modified Silicate Composite CoatingSurface Modification for Enhanced Corrosion Resistance Using Fluid Bed Reactor Chemical Vapour Deposition (FBR-CVD)Development of Laser Surface Treatment with Excellent Corrosion Resistance and Conductivity Performance on Magnesium Alloy ProductsCorrosion Behavior of 6000 Series Aluminum Alloys Produced by Conventional and Powder Extruded Process through Electrochemical Impedance MethodElectrochemical Corrosion Behaviors Using Double Glow Forming TiN Multi-Permeation LayerImpact Indentation Properties and Interfacial Strength of Ceramic CoatingsRelaxor Ferroelectricity and Electrostrictive Behavior of KNN-ST CeramicsEnvironmental Impact Evaluation and Rationalization of Ceramics Process on the Basis of Exergy AnalysisDensification Behavior in Spark-Plasma-Sintering of MgAl2O4 SpinelOptimization of Dielectric Properties of Glass Added BaxSr1-xTiO3 Ceramics for Pulsed Power ApplicationsVSintering and Nonlinear Dielectric Properties of Ba0.6Sr0.4TiO3 Ceramics Prepared by Citrate MethodStructure and Diffused Ferroelectric Properties in Ba(Ti0.8Sn0.2)O3 CeramicsMillimeter-Wave Reactive Sintering of Neodymium-Doped Yttrium Aluminum GarnettSolid-State Reaction Synthesis and Mechanism of Lithium Silicates Reaction Sintering Kinetics of Mullite Ceramics Prepared from High Aluminum Fly AshSolid-State Synthesis and Properties of Y-Doped BaCeO3Effect of Ti Content on Microstructure and Mechanical Properties of Si3N4/Si3N4 Joints Brazed with Ag-Cu-Ti+Mo Composite FillerPreparation of Magnesium Carbonate Whisker by Using Magnesite TailingsPreparation and Luminescent Properties of Na5Eu(MoO4)4-x(PO4)x Red Phosphors for White Light-Emitting Diodes ApplicationFerroelectric and Photocatalytical Properties of Ta-Based and Nb-Based Oxide Ceramics and Powders from Environmentally Friendly Water-Soluble Tantalum and Niobium PrecursorsInfluence of Fiber Properties on the Performance of Piezoelectric 1-3 CompositesEffect of LiNbO3 on Piezoelectric Properties of K0.5Na0.5NbO3 CeramicsOptical Properties of Transparent MgO-Doped Alumina Fabricated by Spark Plasma SinteringCharacterization and Energy Storage Density of BaTiO3 - Ba(Mg1/3Nb2/3)O3 CeramicsHigh Performance of Sub-Micro-Layered Ti3C2/(Cu-Al) Cermets Prepared by In-Situ Hot-Extruding MethodNanostructured Titanium Biomaterials: Understanding and ApplicationsLaser Forming of Ti-6Al-7Nb Alloy Powder Compacts for Medical Devices Nanotube and Micropore of Ti Alloy Systems for Biocompatibility
In Vitro and In Vivo Evaluation Of Calcium Phosphate Bone Graft SubstitutesMathematical Modeling of Polymer Biodegradation and ErosionDevelopment of Polyimide/SMA Thin-Film ActuatorAustralian Defence Applications of Advanced Smart Materials ResearchThe High Temperature Connecting Strength and Thermal Stability of Ti44Ni47Nb9 SMA Pipe CouplingDesign of a New Biocompatible Ti-Based Shape Memory Alloy and Its Superelastic Deformation BehaviourComputational Modelling of Deformation of NiTi Plates with Circular HolesEffect of the Addition of Gd on Ni53Mn22Co6Ga19 High-Temperature Shape Memory AlloyHysteretic Behavior of Concrete Cylinders Confined by Active Confining SMA Wire JacketsCompression Behavior and Texture Development of Polymer Matrix Composites Based on NiMnGa Ferromagnetic Shape Memory Alloy ParticlesShape Memory Effect in Fe-Pd Magnetic Shape Memory Alloy Thin FilmsNew SMA Actuator with High Energy Efficiency and Quick ResponsePhase Stability and Mechanical Properties of Ti-Cr Based Alloys with Low Young?s Modulus Phase Constitution and Mechanical Properties of Ti-(Cr, Mn)-Sn Biomedical AlloysPhase Constituents of Ti-Cr-Au and Ti-Cr-Au-Zr Alloy SystemsEffect of Nitrogen Addition on Mechanical Property of Ti-Cr-Sn AlloyBiomedical Titanium Alloy with Ultralow Elastic Modulus and High StrengthEffect of Oxygen Addition on Isothermal Omega Phase Stability in Ti-29Nb-13Ta-4.6ZrEffect of Y2O3 on Mechanical Properties of Ti-29Nb-13Ta-4.6Zr for Biomedical ApplicationsImprovement of Mechanical Performance and Biocompatibility of Spinal Implant Rod Made of Beta-Type Ti-Nb-Ta-Zr AlloyMicrostructure Characterization of Laser Welded Near-? Titanium Alloy ?TLM? under Different Process ConditionsEffect of Aging on Mechanical Properties of Ti-Mo-Al Biomedical Shape Memory AlloySelf-Accommodation Morphology in Ti-Nb-Al Shape Memory AlloyFabrication of Ti-Based Biodegradable Material Composites Prepared by Spark Plasma Sintering MethodCalcium Phosphate Coating on Titanium Using Dry ProcessMAO-Prepared Hydroxyapatite Coating on Ultrafine-Grained TitaniumPack Cementation Treatment of Titanium Using Tetracalcium Phosphate Powder for Biomedical ApplicationsPhase and Morphology of Carbides in ASTM F75 Co-Cr-Mo-C Alloys Formed at 1473 to 1623 KHeat Treatment of ASTM F75 Co-Cr-Mo-C-Si-Mn AlloysGrain Refining Technique and Mechanical Properties of the Biomedical Co-Cr-Mo AlloyEffect of Temperature and Strain Rate on Microstructure of Dynamically Recrystallized Ni45Co5 Mn36.7In13.3 AlloyBiodegradable Mg-Ca and Mg-Ca-Y Alloys for Regenerative MedicineCalcium Phosphate Deposition on Magnesium Alloy for Bioimplant ApplicationsEffect of Cu Content on Unique Hardening Behavior of Dental Ag-Pd-Au-Cu System Alloy Subjected to Solution Treatment Investigation of Biomimetic Apatite Growth on DLC-ZrO2 Thin Films Prepared by MOCVDEffect of Grain Boundary Segregated Dopant on Phase Stability in Tetragonal Zirconia Polycrystal Evaluation and Control of Crystallographic Alignment of Biological Apatite Crystallites in BonesChange in Biological Apatite Orientation in Beagle MandibleEvaluation of Mechanical Properties of Regenerated Bone by Nanoindentation TechniqueEffect of Penetration Rate on Insertion Force in Trabecular Bone BiopsyCreating Biomaterials Inspired by the Microstructure of CuttleboneFabrication of Artificial Bone by the Combination of Electrospinning, Extrusion and Slurry ProcessesBiomimetic Artificial Cortical Bone with Aligned Microstructure Formed by a Combination of Multi-Extrusion and Rolling ProcessesQuantity and Quality of Regenerated Bone in Grooves Aligned at Different Angles from the Implant SurfaceFabrication of Bone Substitutes by the Sponge Replica MethodChanges of Bone Quality and Quantity in rhM-CSF-Treated Osteopetrotic (op/op) MiceNano-Hardness Testing of Wear Particles in Sheep Knee Joints Formation of Hydroxyapatite on Titanium Oxides in Simulated Body Fluid under UV IrradiationA Study of a Retention of Antimicrobial Activity by Plasma Polymerized Terpinen-4-ol Thin FilmsSimultaneous Incorporation of 5-Fluorouracil and Leucovorin into Chitosan Nanoparticle as Drug Carrier and Its CharacterizationA Novel Biodegradable Multichamber Microstructure for Implantable Drug Controlled ReleaseOn the Effective Mechanical Properties of Fluid-Saturated Composites: A Homogenization ApproachSynthesis and Characterization of Mesoporous Carbon with MoO3 Loading via Ultrasonic Assembly The Study of Cotton Finishing by Artemsia Argyi Oil MicrocapsulesElectrochemical Synthesis of Sensitive Layer of Polyaniline: Effects of Acid Doping on Ethylene Gas SensingProperties of Polyethylene Foam Incorporated with Extracted Lignin from Pulping Black LiquorDynamic Atomic Mechanisms of Plasticity of Ni Nanowires and Nano Crystalline Ultra-Thin FilmsDefect and Damage Evolution Quantification in Dynamically-Deformed Metals Using Orientation-Imaging Microscopy3D Characterisation of Grain Deformation under Synchrotron RadiationCharacterization of Crack-Tip Dislocations and their Effects on Materials FractureMechanical Properties Evaluation of Nano-Structured Materials in Scanning Electron MicroscopeMultiscale Mapping of Mechanical Properties by Instrumented Indentation TestX-Ray Phase-Contrast Tomography for Quantitative Characterisation of Self-Healing PolymersNucleation of Bainite on Allotriomorphic Ferrite/Austenite Interface in a Low Carbon SteelPrecipitation Behavior in AL6XN Austenitic Stainless SteelThe Study on the Nucleation Behaviours in IF Steel by 3-D EBSD TomographyGrain Boundary-Dependent Selection Criteria for Nucleation of Gamma-Massive Grains in TiAl-Based AlloysPrecipitation Behavior and Magnetic Properties of Nano?Scale Particles in a Cu?Fe?Ni AlloyCoarsening Process of Decomposed Phases in Cu-Ni-Cr AlloysGrain Boundary Engineering and Alterations in Anisotropy of Interfacial PropertiesTexture Distribution and Development through the Thickness of Grain Oriented Silicon SteelThree Dimensional Microstructure Characterization of an Al-Zn-Mg Alloy Foam Using Synchrotron X-Ray MicrotomographyTEM and STEM Study of the Au Nano-Particles Supported on Cerium OxidesChallenges Associated with the Characterisation of Nanocrystalline Materials Using Atom Probe TomographyThe Fluctuation of Indium Composition in InGaN Based LED Investigated by Atom Probe Tomography (APT)Characterisation of the Densification Mechanism of Plasma Sprayed CordieriteMicrostructure for Printed Multilayer LTCC Tape of Different Paste RheologyEffect of Alumina Starting Materials on Spheroidization in Flame Fusion MethodEffects of Doping Elements on Residual Oxygen/Nitrogen Contents in Red Pigment of Tantalum Nitrides (Ta3N5)The Bonding Structure of the Various High Purity or Binderless Polycrystalline Cubic Boron Nitride Compacts Sintered at 5 to 7GPa and 1600 to 2000 ?CDefect Observation of Embedded Components of a Low Temperature Co-Fired CeramicThermal Decomposition of Pyrite FeS2 under Reducing ConditionsShape-Controlled Syntheses of Silver Nanoparticles: Role of the SeedsPreparation of Highly Crystalline Mesoporous TiO2 by Using Carbon to Protect the Pore Structure at Elevated TemperatureProperties of Screen Printed Ceramic Green Films Determined by Optical Laser ProfilometryUsing Chemiluminescence to Study the Photodegradation of MaterialsStudies on Estimating Methods of Polarization Performance for Coated Steel in SeawaterPost-Hydrogen Permeation Characterization of V-Based Crystalline Alloy MembranesHigh-Throughput Evaluation of Crystallization Temperature of Pd-Cu-Si System Using Integrated Thin Film SamplesStructural Characterization of Electrodeposited Nickel-Iron Alloy FilmsSurface Damage in Riveted Aircraft Aluminium Lap Joints, in the Presence of LubricantsTesting of Aluminium Carbide Formation in Hall-Heroult Electrolytic CellThermodynamic Evaluation of the Fe-Pr Binary SystemNanoindentation Characterization of Intermetallics Formed at the Lead-Free Solder/Cu Substrate InterfaceFormation and Mechanical Properties of Intermetallic Compounds in Sn-Cu High-Temperature Lead-Free Solder JointsMicro-Scratching of UHMW Polyethylene SurfacesA New Micromechanical Elasto-Plastic Constitutive Model for Fiber-Reinforced Composite LaminatesMechanical Properties of Metallized Single NanofibersSynthesis, Characterization and Analytical Modelling of Mechanical Behavior of a Conducting Polymer ActuatorRheological Properties of a Particulate-Filled Polymeric Composite through Fused Deposition ProcessStructural Characteristics of Pultruded FRP Composite Experienced Freezing and Thawing Cyclic TemperatureFatigue Fracture Behavior of ARB Processed AluminumNumerical Simulation of Double Specimens in Split Hopkinson Pressure Bar TestingStudy on Stress Distribution Near Crack Tip in Beryllium Compact Tension SpecimenMicrostructure Features and Contact Fatigue Crack Growth on RailEvaluation of Residual Stress of Railway Wheel Regarding to DeteriorationEvaluation of Surface Defects of Wheel and Rail for Korean High-Speed RailwayInfluence of Mechanical Loading on Failure of Aircraft Protective CoatingsProperties of PH 13-8 Mo Steel for Fatigue Application in HelicoptersThe Laser Surface Remelting of Austenitic Stainless SteelA Study of Toughness Degradation in CA6NM Stainless SteelHydrogen Evolution Behavior during Tensile Deformation in Austenitic Stainless Steels Exposed to High Compressed Hydrogen AtmospheresThe Microstructure and Mechanical Properties of Ni-Based Superalloy after Service Exposure in Gas TurbineWear Resistance and Microstructural Study of Diamond Coated WC ToolsTool Failure Criteria while Drilling Titanium AlloysEffects of Strain Rate on Mechanical Properties and Microstructure of V-5Cr-5Ti AlloyFailure Analysis on the RivetHigh-Speed Fracture Phenomena of Glass Bottle by Underwater Shock WaveDesign of Pre-Weakening and Evaluation of Structural Safety for Explosive Demolition of Concrete SiloMicrostructure and Mechanical Properties of High Strength Brass Alloy with Some ElementsTensile Properties of Processed FDM Polycarbonate MaterialMechanical Properties of 5083 Aluminium Welds after Manual and Automatic Pulsed Gas Metal Arc Welding Using E5356 Filler Evaluation of Fretting Wear Behavior on the Simulated Supporting Structures of a Dual-Cooled Nuclear Fuel RodEffects of Aging Parameters on the Mechanical Properties in Corson Alloy System with High Contents of Ni and SiThermo-Physical Properties of Ti-Coated Diamond/Al Composites Prepared by Pressure InfiltrationComputational Analysis of the Structural Integrity of Self-Healing CompositesEffects of Deformation-Induced Heating on Bond Strength of Rolled Metal MultilayerA Study on Improvement of Fatigue Life for Woven Glass Fabric/Epoxy Laminate Composite Applied to Railway VehiclePreliminary Review of Physically Based Methodologies for Predicting the Strength of Visibly Damaged Composite LaminatesCrack Propagation Monitoring of DCB Composite Specimens Using Distributed Optical Fiber SensorResidual Strength of a Helicopter Composite Structure Subjected to Small Arms FireEffect of Humidity and Thermal Cycling on Carbon-Epoxy Skin/Aramid Honeycomb StructureMechanical Reinforcement of Three-Dimensional Spacer Fabric CompositesQuantification of the Interface Interactions in Polymer NanocompositesPolymer Based Composite and Hybrid Materials for Wind Power GenerationThe Indentation Behaviour of Carbon Fibre Composite Tubes-Experiments & ModellingDevelopment of High Modulus/High Strength Carbon Fiber Reinforced Nanoparticle Filled Polyimide Based Multiscale Hybrid CompositesCharacterization and Properties of Recycled Cellulose Fibre- Reinforced Epoxy-Hybrid Clay NanocompositesMechanical Properties of Metallic Closed Cellular Materials Containing Polymer Fabricated by Polymer PenetrationExtended-Chain Crystals of High-Pressure Crystallized Poly (Ethylene Terephthalate) Oligomer/Bisphenol-A Polycarbonate BlendsImprovement of Mechanical Properties of Injection Molded Wood/Polypropylene Composites Parts with Ultrasonic Oscillation AssistantStrength Evaluation of Bolted Connection in PFRP Structural MemberAn Experimental Investigation on the Structural Behavior of FRP-Concrete Composite Compression MembersForm Factor for the Design of Pultruded FRP Structural Members under CompressionThermal Decomposition and Kinetic Study on Different Types of Glass Fiber/Unsaturated Polyester Pipe WastePerformance of Aluminium / Vinylester Particulate CompositeStrength & Stiffness Estimation for Center Frame of Low-Floor VehicleA Study on Structual Strength in Body Structure of Composite MaterialModelling of Reinforced Asphalt Products for Road ApplicationsDesign of a Composite Side Beam for the Railway Bogie FrameHigh Strength and Lead-Free Machinable Brass by Powder Metallurgy ProcessThe Effect of a Small Volume Liquid Phase on the Hot Deformation in the BaPbO3/2024Al CompositeComposite Filler Metals for Joining Temperature-Sensitive Aluminium- Matrix CompositesFabrication of Carbon Nano-Fiber / Aluminum Composites by Low-Pressure Infiltration MethodEffect of Interfacial Reaction on High Temperature Properties of Fe-Cr-Si Fiber Reinforced AC8A Aluminum CompositesBallistic Performance of Zr-Based Bulk Metallic Glass/Ti Surface Composites Fabricated by High-Energy Electron-Beam IrradiationMicrostructure and Interface Of Mg3Zn6Y Quasicrystal Particulate Reinforced Mg-8Gd-3Y AlloyInterfacial Characteristics of WC Particles Reinforced Hadfield Steel Matrix CompositesCast Bonding of Cast Irons to Ferritic Stainless SteelEffectiveness of Residual Stress on Forming Copper Patterns of Printed Circuit BoardThermal Stability of Fe Filaments in Deformed Cu-Fe CompositesEffects of Cu Powder Size on the Microstructure of TiB2/Cu Composites Fabricated by Reactive Infiltration ProcessFabrication and Properties of a Combined Structural Cu Sheet for Interconnect MaterialA Research on Interfacial Reaction of Brazing Joint of Alumina Ceramics to MetalsAnatase-Type Ti1-2xNbxAlxO2 Solid Solution/Silica (SiO2) Composite Nanoparticles: Synthesis, Phase Stability, and Photocatalytic PerformanceSynthesis of Ni3Al/ZrO2 Nanocomposite and Study on Its High Temperature Oxidation in Mixed Gas EnvironmentCrystallization of Amorphous SiCN Matrix of C/SiCN Composite under Conditions of Vacuum and Tension-Tension FatigueElectronic Structure of Bilayer (Fe, Ni) Metallic a-Al2O3(0001) Catalysts Towards CH4 Adsorption and DissociationApplication of SPH for Modelling Heat Transfer and Residual Stress Generation in Arc WeldingA Study on B-Stage CNT / Epoxy Composite Films for Electronic Packaging ApplicationsSuperconductive Property and Microstructure of MgB2 Particle-Dispersed Aluminum Based Composite MaterialsFriction and Wear Behaviors of Solid Lubricants/Polyimide Composites in Liquid MediumsCorrosion and Wear Resistances of Ni-P-Al2O3 Composite Film Prepared by Electroless PlatingEffect of TEOS Addition on Adhesion and Electrochromic Properties of Silica-Polyaniline Core-Shell Composite Films on ITO GlassA Method to Extract Materials Properties from Multilayer Material SystemsSynthesis and Characterization of the Layered Hybrids (CnH2n+1NH3)2MCl4 (M=Co,Cu,Zn and n=2,4,6,8,10,12)Effects of Carbon Black and Carbon Nanotube on Mechanical and Thermal Properties of 80NR/20SBR CompositesFabrication of Solid Oxide Fuel Cells via Thin Film TechniquesSuperior Radiation Resistance of ODS Ferritic SteelsThermoelectric Performance of Half-Heusler TiNiSn Alloys Fabricated by Solid-Liquid Reaction SinteringBroad-Band Vibro-Impacting Energy HarvesterStructural Design for the Development of the Floating Type Photovoltaic Energy Generation SystemFabrication of Nanocrystalline TiO2 Films by Aerosol Deposition Method for Dye-Sensitized Solar CellsVariation of Heat Dissipation Properties of LED Packages with Thermal ViasThermodynamic Characterization on Hydrogen Absorption and Desorption Reactions of Lithium ? Silicon AlloyHydrogen Storage in Nitrides by the Use of Ammonia as a Hydrogen CarrierHydrogen Permeation Properties of Pd-Coated Ni37.5Nb27.5Zr25Co5Ta5 Amorphous MembraneA New Concept for Alloy Design of Nb-Based Hydrogen Permeable Alloys with High Hydrogen Permeability and Strong Resistance to Hydrogen EmbrittlementHydrogen Permeation of Pd-Free V-Based Metallic Membranes for Hydrogen Separation and PurificationInfluence of Temperature on Self-Discharge and High-Rate Discharge Characteristics of La-Rich AB5-Based MH Alloy ElectrodeEffect of Annealing on the Hydrogen Permeation and Mechanical Behaviour of Nb-Ni-Zr Alloy MembranesHydrogen Storage Properties of Mg-Ni Alloy Catalysed by Multi-Walled Carbon NanotubesThe Effects of Cryogenic Milling and Catalytic Additives on the Hydrogen Desorption Behaviour of Nanostructured MgH2Characterisation of Hydrogen Release Behaviour in Cast Mg-Ni Alloys by Synchrotron XRD and XAFSHydrogen Exchange Effect in MgH2-LiBH4 SystemObservation of Hydrogen Distribution in a Eutectic Mg-Ni Alloy by the Silver Decoration MethodCatalysing Effect of Intermetallic Compounds on Hydrogen Desorption Kinetics in Cast Magnesium Alloys
In-Situ TEM Observation for Dehydrogenation Mechanism in MgH2 with CatalystHigh Water Diffusivity in Low Hydration Plasma-Polymerised Proton Exchange MembranesDevelopment of High Power Density Solid Oxide Fuel Cells (SOFCs) for Long-Term OperationEffect of Flow Fields and Scan Rates on Performance of Micro-DMFCRare Earth Element Aliovalent Doping Substitution and Electrochemical Performance of LiFe1-x NdxPO4Effect of Dissolved Hydrogen on the SCC Susceptibility of SUS316L Stainless SteelJoining of ODS Steels and Tungsten for Fusion ApplicationsEffects of Chemical Composition on the Impact Properties of A533B SteelsResistance to Hydrogen Embrittlement and Behavior of Hydrogen in 6000 Series Aluminum AlloysVisualization of Diffusive HydrogenSynthesis of Ni-Al Intermetallic Nanoparticle Catalysts by Vacuum Arc Plasma EvaporationNeutron Irradiation Hardening of Fe-Based Binary AlloysEvaluation of Irradiation Hardening of Fe-Ion Irradiated F82H by Nano-Indentation TechniquesMicrostructural Evaluation of Dy-Ni-Al Grain-Boundary-Diffusion (GBD) Treatment on Sintered Nd-Fe-B MagnetChemical Property of Ground Calcium Carbonate as Carbon Dioxide Absorbent Storage of CO2 in Low Al2O3 EAF Oxidizing Slag by Grinding with Vibration Mill Fabrication of (Al2O3-Al3Nb)/Al Composite Materials by In-Situ Reaction Using MA Processed Al/Nb2O5 PowderResearch and Development of Nano-Composite Materials for Hydrogen Storage