Advances in Materials and Processing Technologies XVI

A Structure and Morphology of Nanocomposites Composed of Carbon Nanotubes with a Varying Fraction of Platinum NanoparticlesAnalysis of Influence of Aluminum Content on Inclusion Characteristic and Fatigue Life of Bearing Steel Using Statistics of Extreme ValuesDeformation Behavior of Adhesive Layer in Stretch-Bending/Unbending for Adhesively Bonded Sheet MetalsDeformation Behaviour of TRIP Steel Monitored by In Situ Neutron DiffractionDeformation Evolution of a Zr-Based Bulk Metallic Glass under Three-Point Bending TestsEffect of Interference-Fit on Fatigue Life for Composite Lap JointsEffect of Temperature on Cyclic Behavior of AZ31 Mg Alloy SheetEffects of Scoring Depth, Tracking Angle, Rubbering on Bending-Moment Relaxation of Creased PaperboardHarmonic Structure Design of Co-Cr-Mo Alloy with Outstanding Mechanical PropertiesNew Design of Aluminium Based Composites through Combined Method of Powder Metallurgy and ThixoformingResearch of Large-Area Electrical Discharge Machining for Insulating Si3N4 Ceramics with the Assisting Electrode MethodRole of Halloysite Nanoparticles and Milling Time on the Synthesis of AA 6061 Aluminium Matrix CompositesTensile Properties and Microstructure of Joined Vacuum Die Cast Aluminum Alloy A356 (T6) and Wrought Alloy 6061Processing of Epoxy-Nickel Matrix Composites Reinforced with Aluminum and Waste ElastomersWear Resistance of Elastomeric Based Composites by Continuous Multi-Cycle Indentation Used in Manufacturing EngineeringNew Design of Composite Materials Based on Scrap Rubber Matrix Reinforced with Epoxy and SiCYSZ-Reinforced Mg-Based Amorphous Composites: Processing, Characterisation & CorrosionSearch for Rapid Quality Control of Ni-Cr-Mo Low Alloy Steels Using Multifaceted Approaches for Fracture Toughness EstimationShaping Porous, Low Density Al Composites by AWJ Cutting ProcessTensile Property of Electrochemically Polished Titanium AlloyThe Effect of Particle Deformation on Densification of 316L Stainless Steel under Micro-FASTApplication of Electrochemical Discharge Machining to Micro-Machining of QuartzApplication of Idling Stop Technology for Servo Motors in Machine Tool Operations to Reduce Electric Power ConsumptionApplications of Optical Path Length Compensation Technology for High Power CO2 Laser Cutting ProcessBonding PDMS Microfluidic Devices to PMMA and Glass Substrate Using Pulsed UV Laser TechnologyFinite Element Modeling of the Effect of Tool Rake Angle on Cutting Force and Tool Temperature during High Speed Machining of AISI 1045 SteelInvestigation of Chatter Vibration in End-Milling Process by Considering Coupled System ModelMicro Cutting of Biliary Stent with Nanosecond Fiber Laser SystemTemperature Distribution of Micro Milling Process due to Uncut Chip ThicknessThe Use of Supports to Fast Fabrication of Plastic PartsEffect of Optical Properties Characteristic Polymethylmethacrylate Using UV Laser Direct-StructuringEffect of Punch Surface Topography on Friction in Micro Combined Forward and Backward Extrusion of BrassAn Analytical Model for Deformation Path Design in Multistage Incremental Sheet Forming ProcessEffect of Edge Shape of Tool in Finish BlankingForming Limits of Several High-Strength Steel Sheets under Proportional/Non-Proportional Deformation PathsStiffness Improvement of Stamping Die by Means of Topology OptimizationStudy on Step Depth for Part Accuracy Improvement in Incremental Sheet Forming ProcessBulging Investigation of Cylinder Compression Forming Using Upper Bound AnalysisA Study of Hole Flanging-Upsetting ProcessComparison of Cast and Extruded Stock for the Forging of AA6082 Alloy Suspension PartsEffect of Counter Punch Pressure on Springback of High Strength Steel SheetExperimental Study and Efficient Prediction on Forming Forces in Incremental Sheet FormingIncremental Sheet Forming (ISF) of AISI 316 Stainless Steel Sheet Using CNC Milling MachineInfluence of Pre-Generated Infinite Adhesive Defects on the Forming Behaviour of Adhesive Bonded Steel SheetsInfluence of Wire Reinforcement on the Forming Behaviour of Adhesive Bonded Steel SheetsInfluences of Process Conditions on Stretching Characteristics of Crystalline Polymer FilmPrecision Glass Molding of High Filling Factor Micro Lens ArraysResearch on Formability of Aluminum Alloy Automotive Panels by Using Viscous Pressure FormingSpringback of Aluminum Alloy Sheet Metal and its ModelingTheoretical and Experimental Studies on the Influence of Process Parameters on Strains and Forces of Single Point Incremental FormingVerification of Numerical Roll Forming Loads with the Aid of Measurement EquipmentOn Flow Layer Uniformity in the Co-Extrusion of Polymer Multilayer FilmDevelopment of Looper Shape Meter and Verification Test Results in Hot RollingDirect Thermal Method of Aluminium 7075Effect of Heating on Springback in Heat Assisted MicrobendingFlow Stress and Pyroplastic Behaviour of Ultra-Low Carbon Steel in Warm Temperature RangeInfluence of Cooling Conditions on Forming Performance of Hot Stamped and Press-Quenched Steel Sheet PartThermomechanical Forming of NiTi Shape Memory Alloy WireDesign and Test of a Rapid Thermal Annealing Furnace for Improving Surface Properties of Silicon Brick in Multi-Wire Sawing ProcessA New Approach to Calibration of Printed Circuit Board Coordinates: 2D-Depth Sensor Applied to Robotic Screwdrivers Assembly SystemsDeformation Behavior and Wear Resistance of Hard TiCN and TiCN/Ti Coatings on Ti6Al4V AlloyDesign of Experiments to Study Slurry Erosive Wear Behavior of Inconel-718 Coatings on CopperGa-Doped ZnO Films Deposited by Atmospheric Pressure PlasmaA New Concept of the Sliding Compression Test to Independently Investigate the Contact Normal Stress and the Surface EnlargementDevelopment of a Self-Propelled Multi-Jet Polishing Tool for Ultra Precision PolishingSurface Roughness Measurements of a Narrow Borehole?? Development of Stylus with Cylindrical Mirror and Lensed FiberThe Numerical Research of Drag Reduction over Bionic Fluctuation-Adaptive Non-Smooth SurfaceAssessment of Using Secondary Concentrators for Nonferrous Material Removal ApplicationsA Study on the Structure Analysis of Skate for Transportation Using Composite MaterialsA Study on the Warm Forging-Flaring Process of Brass TubeDynamic Simulation and Analysis of Large-Scale Gear ReducersFlow and Film-Forming Characteristics Analysis of Non-Newtonian Fluid Slot CoatingInvestigation of Drilling Conditions of Printed Circuit Board Based on Data Mining Method from Tool Catalog Data-BaseInvestigation of Gear Meshing Noise of Planetary Gear Mechanism for Hybrid VehiclesPrediction of Maximum Forging Load and Billet Volume Using FEM of a Near Net-Shaped Helical-Bevel Gear ForgingStudy on Utilizing Rapid Prototyping Technology to Build Oral and Maxillofacial ModelsThe Development of a Cross-Flow Fan for Electronic Devices Cooling with a Focus on Laptop ComputersThe Study on the Boltzmann Distribution of Ideal Gas under Gravitational Field by Computer SimulationThe Effect of Seat Tube Angle (STA) on Muscle Tension Leg RidersGeneralized Two-Point Method for Straightness Profile Measurement - Error Propagation and Experimental ResultsControl of Service Robot by Integration of Multiple Intermittent SensorsDevelopment of an Advanced Semi-Active Damper Using Smart FluidHybrid Genetic Algorithm for Solving Assembly Line Balancing Problem in Footwear IndustryPerformance Analysis of an Open-Cathode PEM Fuel Cell StackA Survey of Sustainable Design-Centered Integration for Medical Additive ManufacturingDevelopment and Optimization of a Low Normal Force ContactMechanism of TiO2 Nanotubes Formation on the Surface of Pure Ti and Ti-6Al-4V AlloyNano-Scale Control Design and its? Practical Implementation of Piezoelectric MaterialsThe Nanostructure Fabrication on Conductive Diamond-like Carbon Thin Film by Nano-Oxidation TechniqueThe Study of Aluminum Pattern on Phosphors Anode in Field Emission DeviceThe Study on the Ultrasound Assisted Atomic Force Microscopy Base Nanomachining