Operation and Diagnostics of Machines and Production Systems Operational States III

Physical-Mechanical Properties of Hollow Glass Microspheres Filled Polypropylene Composites for Injection MouldingInfluence of Process Conditions on the Local Shrinkage and on the Pressure Evolution inside the Mold Cavity of the Injection Molded Polypropylene in Two Modifications - PP Homopolymer; 40 % Talc Filled PPObservation of Impact of Progressive Cooling System on Temperature Field Distributions on Surfaces of Injection Moulded Plastic PartsCompacting Technologies of Polyethyleneterephtalate BottleGate Location and its Impact to Flowing Characteristics of Plastic MoldingsTwo Component Parts Hardness Optimization Regarding Production SystemsNew Silane and MAPP Coupling Agents as Natural Composites Production Systems ImprovementApplication of Taguchi Method for Cutting Force Optimization in Metal MachiningCooling Thin Parts of Pressure Casting Moulds by Means of Liquid CO2Study of Welding Parameters Effect on the Weld Quality for Structural Steel S235 J0Study on Edgetrimming of Holes in the Thick Steel Plates by Metal Plastic Forming TechnologyProposal of the Knowledge Application Environment of Calculating Operational Parameters for Conventional Machining TechnologyProgressive Trends of Die Casting - Vacuum Treatment of Casting MoldDiagnostics of Aluminum Alloys Melting Temperature in High Pressure CastingMachinability Research by New Abrasion-Resistant Cast Irons CuttingCreation of Mathematical Prescription of Residual Stress Depending on Various Cutting ConditionsHomogeneity of Aluminum Castings and Dependency on Increasing PressureDiagnostics of Material Properties of Steel Sheets from the Tensile Test RecordDetermination of Relationship between Chemical Composition of Electrolyte and Surface Sample QualityDiffusion Niobizing of Titanium Grade 2 by Gas-Contact MethodAdhesive Bonding Joints of Coating with Zn/Mg Layer on Sheets for Car-Body Panels at Temperature LoadingVibration and Experimental Comparison of Machining ProcessFactors Influencing Hydroerosion Surface TopographyComparison and Analysis of the Flow RateMeasuring, Processing and Evaluating of Technology Head Water Jet Vibration SignalAnalysis of the Effects of Factors in Relation to Vibration of Technological Head during the Splitting of Construction Steels through Hydro-Abrasive SplittingExperimental Investigation and Determination of Abrasive Granularity Change Impact to Technology Head Vibration Generating during AWJ Technology Steel CuttingEvaluation of Vibration Parameters under MachiningDetermination of Optimal Combination of Technological Parametres during AWJ Technology Material Cutting by Means of Created Database ProgrammeMeasurement and Analysis of Mass Flow and Feed Speed Impact on Technological Head Vibrations during Cutting Abrasion Resistant Steels with Abrasive Water Jet TechnologyElimination of Pressure Cylinder Deflection on Two Cylinder Bending MachineFormation and Spreading of Cracks at Die due to Heat FatigueComparison of Software and Calculated Correction of the Tip Radius of Turning Tool for Control System FANUCBearing Rings Turning and the Impact of this Process for Resulting Durability of Selected Cutting Materials DurabilityComprehensive Durability Identification of Ceramic Cutting Materials in Machining Process of Steel 80MoCrV4016Impact of Cutting Speed on the Resultant Durability of Cutting Tool in Machining Process of Steel C45Study of Tool Electrode Wear in EDM ProcessEvaluation of T-Vc Dependence for the most Commonly Used Cutting ToolsAnalysis of Cutting Tools Durability Importance in Turning Process of Steel C60Dynamics of Treatment Device for Die Casting of MetalsReal Time Pressure Control in Pneumatic ActuatorsPredictive Diagnostics of Wet Bottom Boilers Operational States by Calculation of Steam Coal Ash Fluid TemperatureApplication of Sliding Guides to Feeder Device in Aggressive EnvironmentsTechnical and Software Equipment for the Real Time Positioning Control System in Mechatronic Systems with Pneumatic Artificial MusclesA Special Analysis of Significant Phenomena in Diagnostic Signal at Compressors MeasurementDiagnostic Analysis of Cutting Tools using a Temperature SensorAction on Crane Runway Caused by Horizontal Forces due to Crane SkewingApplication and Verification Properties of the Thermal Process ModelMethod for Measurement of Residual Stresses using Eddy CurrentsApplying of Automatic Laser Particle Counter as Technique to Morphology Assessment and Distribution of Wear Particles during Lifetime of Transmission OilsVerification and Comparison of Two Tribodiagnostic Methods for Analyzing of the Worn out Oils in ServiceDynamic Model of the Test Station for Gear Drives Dynamic TestsQuality Assessment of Machined Surfaces by an Optical ProfilometerAnalysis of Hydraulic Oil in Handling Lines Baljer & Zembrod Using the Methods of Tribotechnical DiagnosticsDiagnostics of Surface Errors by Embedded Vision System and its Classification by Machine Learning AlgorithmsAnalysis of Oil Charge ? Instrument of the Production Line Wear Regime PredictionComparison of Dilatometry Results Obtained by Two Different Devices when Generating CCT and In Situ DiagramsDifferential Scanning Calorimetry as a Tool for Quality Testing of PlasticsInnovation Map in the Process of Enterprise EvaluationManufacturing Systems Building and DevelopingProposal of Preventive Maintenance Plan of Experimental EquipmentOptimization of the Production and Logistics Processes Based on Computer Simulation ToolsMaterial Flow Planning for Bearing Production in Digital FactoryAnalysis of the Model Application of Mechanical Equipment for Hydrothermal Treatment at Biogas PlantPossibilities of Application of Computational Intelligence in Monitoring of Heat Production and SupplyMethodical Framework of Flexibility Production Evaluation in Terms of Manufacturing Plant