Injection Molding Processing Data
2nd Edition
Published on 12. November 2018
128 pages
978-1-56990-667-5 (ISBN)
Description
In setting up an injection molding machine, reliable initial processing data is necessary to optimize and stabilize the process, and guarantee excellent results. This powerful tool will provide you with the most important processing data, such as viscosity, thermal properties, mold temperatures, and suggested heater temperatures for the most commonly used materials in injection molding.
This revised and improved second edition covers:
Injection Technology
The Injection Molding Cycle
Useful Equations and Theory
Examples of Calculations of Processing Variables
Polymer Data
Pocket-sized and condensed-yet clear and comprehensive!
More details
Other editions
Additional editions
Alberto Naranjo C. | Maria del Pilar Noriega E. | Juan Diego Sierra M.
Injection Molding Processing Data
Book
10/2018
2nd Edition
Hanser Publications
€19.99
Shipment within 3-4 weeks
Persons
Author
María del Pilar Noriega E., PhD, is R&D and Innovation Director at Daabon Group, Santa Marta, Colombia. Until 2019, she was the Director General of the ICIPC (Medellín, Colombia), and from 1997-2012 was Technical Director of the same institute.
Editor
Tim A. Osswald, Ph.D., is Kuo K. and Cindy F. Wang Professor at the University of Wisconsin-Madison College of Engineering and Honorary Professor of Plastics Technology at the University of Erlangen-Nuremberg and the National University of Colombia. He is the author of many books and book chapters, as well as over 100 papers in the field of plastics technology.
ISNI:
ISNI:
Content
- Intro
- Table of Contents
- 1 Introduction
- 2 Injection Technology
- 2.1 The Injection Molding Cycle
- 3 Useful Equations and Theory
- 4 Examples
- 4.1 Runner System Balance
- 4.2 Shrinkage Prediction
- 4.3 Cooling Time Prediction
- 4.4 Effect of Process Parameters on Shrinkage
- 4.5 Theoretical Energy Consumption in an Injection Molding Process with PS
- 4.6 Processing Conditions of PA6 Parts and Theoretical Power-Cooling Requirement
- 4.7 Theoretical Water Flow Requirement for a Mold for PA6 Parts
- 4.8 Determining Viscosity Constants from the Curve
- 5 Polymer Data (for Standard Materials without Fillers or Modifiers)
- 5.1 Polyolefins
- 5.1.1 Low Density Polyethylene (LDPE)
- 5.1.2 High Density Polyethylene (HDPE)
- 5.1.3 Polypropylene Homopolymer (PP)
- 5.2 Styrenics
- 5.2.1 Polystyrene Homopolymer (PS)
- 5.2.2 High Impact Polystyrene (HIPS)
- 5.2.3 Styrene/Acrylonitrile Copolymer (SAN)
- 5.2.4 Acrylonitrile/Butadiene/Styrene Copolymer (ABS)
- 5.3 Polycondensates
- 5.3.1 Polyamide 6 (PA6)
- 5.3.2 Polyamide 66 (PA66)
- 5.3.3 Polyethylene Terephthalate (PET)
- 5.3.4 Polybutylene Terephthalate (PBT)
- 5.3.5 Polycarbonate (PC)
- 5.3.6 Polyphenylene Ether Modified (m-PPE)
- 5.3.7 Polyether Etherketone (PEEK)
- 5.3.8 Polyarylsulfone (PSU)
- 5.4 Vinyls
- 5.4.1 Polyvinylchloride (PVC) Rigid
- 5.4.2 Polyvinylchloride (PVC) Flexible
- 5.5 Others
- 5.5.1 Polylactic Acid (PLA)
- 5.5.2 Polymethylmethacrylate (PMMA)
- 5.5.3 Polyacetal (POM)
- 6 Appendix
- 7 Definitions
- 8 Further Reading
