Materials Engineering and Science

<ul><li>Preface</li><li>Chapter 1: Properties and Treatment of Structural Metals</li><li>Using Artificial Neural Networks to Predict Hardness and Impact Toughness of Aluminum Alloy 6061-T6</li><li>Effect of Co on Microstructure and Properties of Al-30%Si Alloys</li><li>Comparative Study of the Mechanical Properties of Spot Welded Joints</li><li>Experimental Investigations of Surface Finish Generated by Wire Electrical Discharge Machining</li><li>Experimental Investigations of Hydrodynamic Deep Drawing of Galvanized Steel to Form a Hemispherical and Complex Cup</li><li>Investigation of Fatigue Behavior for Al/Zn Functionally Graded Material</li><li>Alumina Nano Powder Impact on Electrical Discharge Machining of Titanium Alloy Wire</li><li>Chapter 2: Polymers and Composites</li><li>Natural Hybrid Reinforcement Effect on Mechanical Properties of UPE Composite</li><li>Developing Crumbed Rubber Tires / Epoxy Composite, by Surface Treatment with Different Silane Coupling Agents</li><li>Numerical and Experimental Study of Multi-Layer Armors for Personal Protection</li><li>Hardness and Dry Sliding Wear Characterization of Functionally Graded Materials Employing Centrifugal</li><li>The Effect of Filler and Fiber Type on the Behavior of Body Armor Composite</li><li>Enhancement Mechanical, Thermal and Dielectrical Characteristics of Polystyrene Reinforcement by Glass Fiber and Additive Kaolin</li><li>Enhancement the Crashworthiness Parameters Using Natural and Hybrid Composites under Axial Static Crushing</li><li>Enhancement Mechanical Properties of Polymers Reinforcing by Nano Graphene</li><li>The Compatibility Characterization of PMMA/DPET Based Polymer Blend</li><li>Improvement of Tensile and Flexural Properties of Fiber Pre-Stressing Composite by Using Nano Graphene</li><li>Chapter 3: Protective Coatings</li><li>Study the Fatigue Corrosion Behavior of Turbine Blade by Laser Cladding</li><li>The Physical-Mechanical Properties in Aggressive Media of Epoxy Composite Reinforced with Waste Glass Materials</li><li>Effect of Multi-Walled Carbon Nanotubes (MWCNTs) in Reducing the Corrosion Rate in Cr-MWCNTs Composite Coatings</li><li>The Influence of Thermo Mechanical Treatment on Corrosion Resistance of Cu-Al-Ni Shape Memory Alloy</li><li>Boriding Treatment of Low Alloy Steels: Effect of Holding Time and Temperature</li><li>Indirect Production of Chromium Carbides Film on Low Alloy Steel</li><li>Characterization of Functional Polyphenylsilsesquioxane (PhSiO_3/2) Hybrid Glass Reinforced with MWCNTs</li><li>Chapter 4: Laser Processing Technologies</li><li>One-Step Fabricate of Copper Nanoparticles via Pulsed Laser Ablation in Liquid: Influence of Energies on Physical Characterization</li><li>Optimization of CO₂ Laser Parameters for Hole Micro Drilling of PMMA: An Experimental and Theoretical Study</li><li>Multiple-Response Optimization of Aluminum Oxide Nanocoating Prepared by Pulsed Laser Deposition Using Taguchi Design</li><li>Chapter 5: Materials for Optoelectronics, Electronics and Energy Storage</li><li>Absorption Spectrum and Raman Spectroscopy of Coumarin507 Dye Laser in Different Solvents</li><li>Morphological and Optical Study of Black P- Silicon Textured in KOH Bath</li><li>In₂O₃/MoS₂/Reduced Graphene Oxide Nanostructure as Composite Electrodes for Supercapacitors</li><li>Structural Morphological and Optical Investigations of Nano Silver Oxides Nanostructures</li><li>Dielectric, A? Conductivity and Optical Characterizations of (PVA-PEG) Doped SrO Hybrid Nanocomposites</li><li>Characterization of Zinc Oxide Semiconductor Thin Film Treated with Cold Plasma</li><li>Conductivity Modification of ZnO NRs Films via Gold Coating for Temperature Sensor Application</li><li>Chapter 6: Materials for Biomedical Application</li><li>The Biomedical Investigation of Bioceramic Cordierite as Orthopedic Material</li><li>Surface Enhancement of Magnesium Implants for Long Term Applications</li><li>Comparing the Mechanical Behavior of Lamination Resin Reinforced with Two Types of Organic and Inorganic Particles Used in Prosthetic Applications</li><li>A Review of some Characteristics of a Composite Hybrid Socket for Prosthetics Derived from Plant Fibers</li><li>Mechanical Properties of Hybrid Composites PMMA Denture Base with Varying Concentrations of Nano-ZrO₂ and Glass Fiber</li><li>Deposition of Layered Bioceramic HA/TiO₂Coatings on Ti-6Al-7Nb Alloys Using Micro-Arc Oxidation</li><li>Preparation of Bio-Composite Coatings on Titanium Substrate by Electrostatic Spray Deposition</li><li>Antireflective and Hard Multicoat Design for Allyl Diglycol Carbonate Plastic Spectacle Lenses</li><li>Boosted Antimicrobial and Self-Cleaning Activities with MnO₂/ ZnO Coated on Cotton Fabric</li><li>Preparation and Characterization of an Electrospun Polycaprolactone/Polyurethane Scaffold for Soft Tissue Applications</li><li>Mechanochemical Synthesis of Dendrimers as Nanocarriers: A Review</li><li>Chapter 7: Technologies of Chemical Production</li><li>Novel Study of Surface Morphological Properties of Commercial Catalytic Reforming Catalysts Used in Iraqi Refineries by Atomic Force Microscopy (AFM)</li><li>Crystallization by Acid Hydrolysis-Sulfonation of Cellulose Nanofibers from <i>Eichhornia crassipes</i></li><li>Chapter 8: Environmental Protection and Bio-Based Building Materials</li><li>Computational and Experimental Simulation of Pollutant Transport through Multiple Porous Media</li><li>Preparation of Mixed Matrix Membranes Containing COF Materials for CO₂Removal from Natural Gas/Review</li><li>Construction of Magnetic Z-Scheme P-Doped Biobr/CoFe₂O₄ Nanocomposite for Expeditious Visible Light Photocatalytic Palm Oil Mill Effluent Degradation via the Assistance of IO₄^- and S₂O₈^2-</li><li>A Review on Self-Healing Concrete</li></ul>