The 2nd International Conference on Sustainable Engineering, Infrastructure, and Development (ICOSEID)

Preface
Chapter 1: Biomass Processing and Valorization
Exploring the Impact of Pressing Techniques on Mycelium-Based Biocomposites
Synthesis of Activated Carbon Derived from Banana Peel for Application as a Catalyst Support in Fuel Cells
Effects of Liquid Fraction Recirculation during Microwave-Assisted Hydrothermal Carbonization on Properties of Coffee Parchment
Extraction of Gelatin Biopolymer from Short Mackerel Bone (Rastrelliger brachysoma)
Experimental Analysis of Bio-Cementation Effectiveness on Silica Sand with Varying Initial Water Content
The Influence of Different Initial Relative Densities and Ambient Temperature Ranges on MICP Treatment Using Direct-Mixing Injection Method
Chapter 2: Corrosion Prevention
A New Approach in Corrosion Study Using DFT and Monte Carlo Simulation to Investigate the Synergistic Effects Natural Green Inhibitor Citrus Sinensis and Synthetic Benzotriazole on Low Carbon Steel
Increasing the Corrosion Resistance of Type 201 Stainless Steel Pitting by Electrochemical Method in a Citric Acid Solution
Chapter 3: Chemical Technology
Sustainable Biochar Production from Palm Kernel Shell through Slow Pyrolysis: A Life Cycle Assessment of Its Application as an Eco-Friendly Fertilizer
Optimizing Co-Firing Ratio of RDF MSW and Coal in a Fluidized Bed Reactor
Simulation of Hydrogen Gas Production Process from Oil Palm Empty Fruit Bunch (OPEFB) Combine with Carbon Capture Based on Aspen Plus Software
Chapter 4: Building Materials
The Effect of Using Ground Granulated Blast Furnace Slag (GGBFS) as a Partial Substitute for Portland Cement in Fiber Concrete
Effect of Storage Time on Asphalt Modified by KKK60 Prevulcanized Latex
The Effect of PETE, HDPE, and LDPE Type of Plastic Waste as Additive on Compression Strength and Temperature Resistance of Architectural Lightweight Bricks
Chapter 5: Construction Technology
The Application of Base Isolation System as Earthquake Resisting Technology on Mulya Medika Hospital, Samarinda
Design and Performance Evaluation of HVAC Systems with Thermal Load and Duct Sizing Considerations Theater Buildings
Chapter 6: Fault Detection
Integrity Assessment of Offshore Pipeline Subjected to Anchor-Induced Dents Using Finite Element Analysis
Combination of Discriminant Analysis and Minimum Redundancy Maximum Relevance for Induction Motor Fault Diagnosis Using Stator Current Signals
Diagnosing Induction Motor Fault Based on ReliefF Feature Selection Algorithm and Support Vector Machine Model
Chapter 7: Heat Transfer
Numerical Analysis of the Effect of Water Cooling Method on Temperature Distribution and Efficiency of Photovoltaic
Systematic Literature Review of Ice Slurry Compounds: Viscosity Characteristics, Heat Transfer and Applications
Chapter 8: Modelling of Machines and Machine Parts
Design Optimization of Cold Air Intake (CAI) System with Valvetronic to Enhance Engine Performance and Efficiency: A Mitsubishi Lancer Evo VIII Study Addressing SDG 9.4 and 12
Sloshing and Stress Analysis of an API 620 Tank under Seismic Excitation Based on SNI 03-1726-2019: Numerical Evaluation of Code Provisions
Efficiency of Buoyancy Force Generation in a Pump-Based Buoyancy Engine for a Small-Scale Underwater Glider
Analysis of Steam Turbine Generator Overhaul for Efficiency Enhancement at the Power Plant Center of Refinery Unit
A Predictive Maintenance Approach for Centrifugal Pumps: Case Study of Vibration Analysis Using FFT and Phase Difference Diagnostics
Identification of Cavitation in Centrifugal Pump Using Vibration Analysis Method in Hydro Cracking Complex (HCC) Area
Strength Analysis and Remaining Life Estimation of Storage Tank Based on API 650 & 653
Powertrain and Integration Analysis of a Small Converted Electric Multi-Purpose Vehicle with the Finite Element Method
Multifactorial Contributors to the Effectiveness of a Mobile Solar Dryer
Chapter 9: Robotics and Automation
Optimized Design for the Flap Folding System of a Carton Sealer Machine by Automation
Mobile Robot Selection Using AHP MOORA and Simulation Modelling for Material Handling Automation
Design and Dynamic Characteristics of a Two-Legged Wheeled Self-Balancing Robot Platform
Chapter 10: Production Management and Industrial Safety
Innovative Advanced Material Solutions for Integrated Safety Helmets in Mining
Implementing MRP (Material Requirement Planning) for Managing Raw Material Inventory in an Indonesian Plastic Blown Film Company
A Theoretical Framework of Spare Part Inventory Management for Aging Rotating Equipment: A Case Study
The Impact of Lean Tools and Waste Analysis on the Improvement of Process Cycle Efficiency and Manufacturing Lead Time of Pipe Sleeve Fabrication: A Case Study