Polymer Science and Engineering

<ul><li>Preface</li><li>Chapter 1: Joining Technologies</li><li>Ultrasonic Welding of Glass Fiber Reinforced PP Thermoplastic Composites: An Investigation of the Outer Layer Orientation and the Fiber Volume Fraction</li><li>Rate-Dependent Material Properties of Adhesively Bonded Joints - Must Have or Nice to Have?</li><li>Effect of Interface Geometry on Strength of Single Lap Adhesive Joint of Sisal-Glass/Epoxy Laminates</li><li>Effect of Friction Stir Forming Process Parameters on Mechanical Interlock between A5083Alloy and Ultra-Thin Stainless Steel Strands</li><li>Alleviation of Stress Concentration with Rivet-Like Joints Fabricated by Friction-Stir Forming</li><li>Chapter 2: Mechanical Properties and Mechanical Testing</li><li>Mechanical Properties of Hollow Glass Microspheres Filled Jute Woven Comingled Composites</li><li>Energy Absorption Mechanism of Thermoplastic Fiber-Reinforced Plastics under Impact Loading Using Split-Hopkinson Pressure-Bar Method</li><li>Effect of Raw Materials on Properties of Coated Al₂O₃-Al Cermet Materials via Vacuum Sintering Method</li><li>Mechanical Enhancement and Thermal Stability of Composites between Polyamide 11 and Functionalized Graphene Nanoplatelets</li><li>Visualization and Quantification of Stresses at the Ends of Short Fibers Embedded in Epoxy Resin</li><li>Fabrication and Experimental Investigation on Tensile and Flexural Properties for Different Stacking Sequence of Jute and Carbon Fiber Reinforced Epoxy Composite</li><li>Effect of Impregnation Process Parameters on the Mechanical Properties of Carbon Fabric Reinforced Thermoplastic Composites</li><li>Effect of Lamination Direction on the AE Behavior of 3D Printed Specimen during Tensile Testing</li><li>Notch Sensitivity on Fatigue Behavior of Carbon-Carbon Composites</li><li>Observation of Tribological Wear on PEEK Shaft with Artificial Defect under Radial Rolling Sliding Point Contact</li><li>Internal Shear Stress Distribution and Subsurface Cracks of PPS Thrust Bearings under Rolling Contact Fatigue in Water</li><li>Chapter 3: Functional Materials</li><li>Application of Photocatalytic and Adsorption Process for Residue Organic Degradation Using Doped ZnO Composites Hydrogel Beads</li><li>Effect of Ag/ZnO-Graphitic Carbon Nitride on Antimicrobial Activity under Visible Light</li><li>Synthesis of TiO₂ Nanofiber by Solution Blow Spinning (SBS) Method</li><li>Absorption of Water Vapor Using Superabsorbent Polymer Composite Material</li><li>Microwave Absorbance of Double-Layer Laminates of Glass Fiber Composite Containing Carbon Black and Carbon Fiber Composite</li><li>Influence of Lithium Oxide on the Characteristics and Mechanical Property in Willemite Crystal Glazes</li><li>Lightweight Cellular Glass Composite from Eggshell and Glass Cullet Powder for Insulation and Bioactive Glass Applications</li><li>Strength, Durability and Degradation Properties of Bioplates Produced from Durian Seed Mixed with Poly(Lactic Acid)</li><li>Chapter 4: Materials and Structures in Construction</li><li>New Type of Composite Girder Design and Research on Key Mechanical Behavior of JiaoJiang Second Bridge</li><li>Influence of Reinforcement Fiberglass Grids Used in Asphalt Pavement on the Bonding of Layers</li><li>Stress-Strain Properties of Engineered Cementitious Composites (ECC) Exposed to Sulfate Dry-Wet Cycle</li><li>Design of Interlocking Bricks Beam</li><li>Properties of Geopolymer Mortar Subjected to High Temperature</li><li>Mechanical Properties of Recycled Polypropylene Macro Flat Fiber Reinforced Concrete with Rice Hull Ash as Partial Replacement to Cement</li><li>Composite Cement Mortar Mix Using GGBS for Wall Finishing</li><li>Clay Tiles Production Using Palm Ash, Spent Bleaching Earth, and Palm Fiber as Substitute Materials</li></ul>