Contribution of Metallography to Production Problem Solutions II

Preface, Committee
Chapter 1: Degradation of Materials and Failure Analysis
Using Fractography for Determining of Technological Reasons of Defect and Brittle Fractures Occurrence in Steels
The Analysis of Causes of Pressure Bottles Heads Destruction
Material Analysis of the Extended-Life Cobalt-Based Superalloys Used in the Manufacturing of Glass Tools
Operational Degradation of Spheroidal Graphite Cast Iron EN GJS SiMo
Structural Changes of Hot Work Tool Steel due to Heat load
Failure Mechanism of Yttria Stabilized Zirconia Atmospheric Plasma Sprayed Thermal Barrier Coatings Subjected to Calcia-Magnesia-Alumino-Silicate Environmental Attack
Failures of Engineering Structures Caused by Weld Imperfections
Fractographical Analysis of Screws Used for Truck Cab Holding
Causal Analysis of Damage of a Cover
Analysis of Damage of Solder Joint of Heat Exchanger
Failure Analysis of Corrugated Hoses
The Influence of Microstructure on the Fracture Development in Engineering Parts
Analysis of the Failure of the Engine Piston of the AlSi Alloy
Atypical Cases of Welded Structure Failures
Analysis of Causes of Fractures of Terminal Board Bolts
Chapter 2: Surface Defects and Surface Degradation
Application of Metallography in Solving of Manufacturing Defects of Galvanically Plated Polymers
The Use of Metallography for Examination of Causes of Surface Defects on Visual Parts
Influence of Microstructure on Machinability of Material and its Final Surface Quality
Application of Metallographic Analysis Techniques for Detection and Identification of Spray Paint Defects
Influence of the Surface Condition of Specimens on the Size of Coherently Diffracting Domains
Evaluation of Titanium Carbonitride Particles Using Image Analysis and Assessment of their Impact on Machinability
Evaluation of Surface Degradation of Deoxidized AW-AlMg0.7Si Alloy
Metallographic Analysis of Filiform Corrosion
Chapter 3: Degradation of Materials and Failure Analysis of Power Equipment
Analysis of Corrosion Attack on Kaplan Turbine Blades
Analysis of Pipeline Serviceability for Water Supply to Power Plant
Development of Creep Damage in Similar Weld Joints of P92 Steel Pipe

Combining 3D Scanning with Standard Microscopy Methods for Assessment of Pitting Corrosion in Turbine Blades
Failure of a Rotating Blade of a 200 MW Steam Turbine LP Rotor and Options for Eliminating other Similar Breakdowns
Quantitative Evaluation of Secondary Phases in a Weld Joint Made of COST F and FB2 Creep Resistant Steels
The Analysis of Causes of the Damage of a Turbine Blade Made of Ti-6Al-4V Alloy
Chapter 4: Analysis of Properties and Production Technologies of Coatings and Non-Ferrous Alloys
Al-Fe Chips Processed by High-Energy Ball Milling and Spark Plasma Sintering
AZ31 and WE43 Alloys for Biomedical Applications
Metallographic and Fractographic Evaluation of 3D-Printed Titanium Samples to Eliminate Unsatisfactory Mechanical Properties
The Effect of Solution Treatment Temperature on Plastic Deformation and Fracture Mechanisms of Beta-Titanium Alloy
The Role of Different Atmospheric Plasma Spray Parameters on Microstructure of Abradable AlSi-Polyester Coatings
Investigations of Wettability of Wear Resistant Coatings Produced by Atmospheric Plasma Spraying
Chapter 5: Analysis of Properties and Production Technologies of Steels
Effects of Heat Treatment on Microstructure of High-Strength Manganese-Silicon Steels
Influence of Mechanical Stress at High Temperatures on the Properties of Steels Intended for the Manufacture of Fuel Cladding for Generation IV Reactors
The Effect of Isothermal Hold Temperature on Microstructure and Mechanical Properties of TRIP Steel
Effect of Chemical Composition and Heat Treatment Parameters on the Structure and Properties of Vanadis 23 and Vanadis 30 PM High-Speed Steels
Characterization of Microstructure of Hadfield Steel
Analysis of Wrought Iron Metal Part of Cupola Construction in the Main Railway Station Plzen from 1907