Advanced Materials - XV

<ul><li>Preface</li><li>Chapter 1: Properties and Processing Technologies of Non-Ferrous Alloys</li><li>Tribological Characteristics of Modified Hypo Eutectic Al-Si Alloy</li><li>Optimization of Spot Welding Parameters in Similar and Dissimilar Alloys AISI-321 and Inconel-X750 Alloys</li><li>Effect of Structural Modification on Corrosion Behavior of Hypo Eutectic Al-Si Alloy</li><li>Development of Lightweight Aluminum-Titanium Alloys for Aerospace Applications</li><li>Twisting of the Tail Rotor Shaft - A Case Study</li><li>Effect of Ag, In and AgIn Alloying Additions on Microstructure and Texture of Mg-3Al-1Zn Alloy during Multi-Pass Warm Rolling</li><li>Superplastic Behavior of Al-Mg-Mn Alloy: An Experimental & Numerical Investigation</li><li>Optimizing Cold Compression Deformation to Remove Residual Stresses in Die Forged Disc of Al-Mg-Si Alloy</li><li>Effect of Heat Treatment on Tribological Characteristics of CuAl₁₀Ni₅Fe₄ Nickel Aluminum Bronze</li><li>Chapter 2: Nanomaterials and Applied Nanotechnologies</li><li>Tuning of Thermo-Mechanical Performance: Modified Multiwalled Carbon Nanotubes Reinforced SBR/NBR/SR Nanocomposites</li><li>Nickel Coated Carbon Nanomaterial for the Removal of Heavy and Toxic Metals (Cd, Cu) from Water and Wastewater</li><li>Low Temperature Synthesis of Anatase TiO₂ Nanoparticles and its Application in Nanocrystalline Thin Films</li><li>Investigation of Various Nano-Structural Morphologies of Zinc Oxide for their Applications in Dye-Sensitized Solar Cells</li><li>Influence of Carbon Nanotubes on the Interlaminar Properties of Carbon Fiber Aluminum Metal Laminates</li><li>Graphene Oxide Coatings Deposited on Steel Substrate Using Electrophoretic Deposition and Electrochemical Evaluation of Coatings in Saline Media</li><li>Effect of Graphene for Ablation Study of Advanced Composite Materials for Aerospace Applications</li><li>Effect of Ethane-1,2-Diamine on Growth of ZnO Nanorods and Cyclohexane Sensing by Current-Voltage Characteristics Investigations</li><li>Removal of Heavy Metals (Lead, Cadmium and Iron) from Low-Grade Nanoscale Zinc Oxide Using Ammonium Carbonate Solution as a Leaching Agent</li><li>Synthesis and Characterization of MoS₂/TiO₂ Nanocomposites for Enhanced Photocatalytic Degradation of Methylene Blue under Sunlight Irradiation</li><li>Hybrid Effect of TiO₂/Reduced Graphene Oxide Based Composite for Photo-Catalytic Water Splitting and Strain Sensing</li><li>Structural and Electrical Properties of Barium Strontium Cobaltite Nanoparticles Synthesized by Wet Chemical Methods</li><li>Investigations of Non-Linear Viscoelastic Properties for Polypropylene/Clay-Nanocomposites through Melt Flow Birefringence and Damping Function</li><li>A Laser Scribed Graphene Oxide and Polyimide Hybrid Strain Sensor</li><li>Polyaniline Enhanced Supercapacitance of Cobalt Hydroxide Nanowires/Carbon Nanotube Containing Polymer Sponge Layered Composite</li><li>Fabrication and Characterization of Laser Scribed Supercapacitor Based on Polyimide for Energy Storage</li><li>Chapter 3: Functional Materials, Special Composites and Non-Conventional Technologies</li><li>Structural and Thermoelectric Properties of Gd Doped Bi₂Te₃</li><li>Resistivity Enhancement of Sr-Hexaferrite Using Rare Earth Dopant to Minimize Energy Losses</li><li>Improvement in Absorption of Microwaves by Incorporating Additives in Silica Phenolic Composite</li><li>Analysis of Electric Transport Mechanism of Barium Titanate by Impedance Spectroscopy</li><li>Aging Behavior and Electric Field Induced Instabilities in Lead Magnesium Niobate - Titanate Relaxor Ferroelectric Single Crystal</li><li>Dependence of Lattice Distortion and Dielectric Response of Zinc Aluminate on Milling Frequency</li><li>Development and Characterization of Teflon-Copper Composite Material</li><li>Effect of Thermal Treatments on the Schottky Contact between Polycrystalline PbS Thin Film and Gold</li><li>Thermo-Physical Properties Measurement of Advanced TBC Materials with Pyrochlore and Perovskite Structures</li><li>Investigation of Hot Section (Nozzle Guiding Vane) Distress due to Interaction of Thermal Barrier Coatings with CMAS</li><li>Enhanced Corrosion Resistance of SiC_p/ 2009 Al by Cerium and Lanthanum Conversion Treatment</li><li>Preparation of Neodymium Metal by Pyro-Metallurgical Process Using Fluoride Salt</li><li>Failure Study of Two Dissimilar Steels Joined by Spot Welding Technique</li><li>Pressure-Time Study of Slow Burning Rate Ap/HTPB Based Composite Propellant by Using Closed Vessel Test (CVT)</li><li>MOF Derived Catalysts for Oxygen Reduction Reaction in Proton Exchange Membrane Fuel Cell</li><li>Efficient Polymer Scattering Layer Fabrication and their Application in Electrical Properties Enhancement of Perovskite/Silicon Tandem Solar Cells</li><li>Chapter 4: Biomaterials</li><li>Synthesis, Spectroscopic Characterization and Biological Applications of Novel Zinc Complexes with Schiff Bases</li><li>Ni-Cr-Mo Alloy for Dental Prostheses with Low Melting Temperature</li><li>Next-Generation Biomaterials for Bone-Tissue Regeneration: Mg-Alloys on the Move</li><li>Grafting of Silica Particles with Linoleic Acid via Modified Stober's Method for Preconcenrtration of Pesticides in Drinking Water</li><li>Fabrication of Cellulose Acetate/Cellulose-HA Composite Films for Bone Fixation</li><li>Bacterial Disinfection Using Polymer Based Hybrids</li></ul>