Materials Engineering 2017

<ul><li>Preface, Conference Committee</li><li>Chapter 1: Engineering Materials and Applications</li><li>Synthesis and Photocatalytic Activity of Modified TiO₂ Thin Films Prepared by Spray Pyrolysis</li><li>Analysis of Pigment Process and Production Techniques for Use in Nail Polish Systems</li><li>Nanoparticle Gels Obtained from Hardwood and Softwood Bark for Reinforcing of Paper</li><li>Crude Tall Oil as Raw Material for Rigid Polyurethane Foams with Low Water Absorption</li><li>Morphology Analysis and Mechanical Properties of MWCNT Reinforced Nylon-6,6 Nanofiber Mats by Electrospun Method</li><li>Two Component Silyl-Terminated Polyether/Epoxy Resin Systems Mechanical and Rheological Properties</li><li>Variational Approximate and Mixed-Finite Element Solution for Static Analysis of Laminated Composite Plates</li><li>Application of Smart Materials in Structural Elements of Pneumatic Vibroexciters</li><li>Studying Temperature Variations that Occurred during Cold and Hot Rolling of AA5454-O Alloy</li><li>New Tanning Agent with Montmorillonite for Leather Manufacturing</li><li>The Effect of Firing Temperature on the Composition and Microstructure of a Geocement-Based Binder of Sodium Water-Glass</li><li>The Properties of Mesh Reinforced Nonwoven Composites</li><li>Surface Energetic Characteristics of Wood-Polymer Composites, Containing a Valorised Hardwood By-Product</li><li>Some Exploitation Properties of Wood Plastic Composites Based on Recycled High Density Polyethylene and Plywood Production Residues</li><li>Technological Peculiarities of Chromium Carbide-Based Iron Alloy Bonded Cermet</li><li>Comparative Study of a Neat Epoxy and Unidirectional Carbon/Epoxy Composites under Tensile and Impact Loading</li><li>Influence of Silver on Photocatalytic Activity of Nanosized ZnO Doped with Iron Group Metals</li><li>Investigation on Polymer-Mineral Tanned Leather Properties</li><li>Effect of Fiber Orientation on Carbon/Epoxy and Glass/Epoxy Composites Subjected to Shear and Bending</li><li>Processing Technology Development for Organic Clay Suspension System</li><li>Matrix Bondable Antistatic Additives for Fiber Reinforced Thermosets</li><li>Synthesis of Amorphous Calcium Phosphate as a Starting Material for ?-Tricalcium Phosphate</li><li>Local and Systemic Morphofunctional Response of Osteoporotic Rabbits Bone Defect Following Implantation of Strontium Doped Biphasic Ceramic Granules</li><li>Characterization and Recycling of a Low-Coast Derivative Iron Hydroxide Adsorbent</li><li>Bio-Waste Recovery for the Removal of Cr (VI) in Aqueous Solution: Case of the Green Alga <i>Ulva lactuca</i></li><li>Radiological Evaluation of Maxillary Sinus Augmentation with Calcium Phosphate Materials and Influence of Titanium Dental Implant Artifacts</li><li>Chapter 2: Advanced Technologies in Materials Science</li><li>Buckling of Eccentrically Loaded Carbon Nanotubes</li><li>Fatigue Crack Growth and Threshold Behavior of DMLS Ti6Al4V</li><li>The Influence of Processing Parameters on Mechanical Properties of Spark Plasma Sintered Chromium Carbide Based Cermets</li><li>Peculiarities of Photovoltage Formation across p-n Junction under Illumination of Laser Radiation</li><li>Extraction and Characterization of Collagen Obtained from Collagen-Containing Wastes of the Leather Industry</li><li>Overall Heat Transfer Coefficient of Functionally Graded Hollow Cylinder</li><li>Chapter 3: Surface Engineering and Tribology</li><li>Evaluation of Wear Rate of Nanocrystalline Diamond Films Using Abbott Curve</li><li>Morphology and Tribological Behaviour of Amorphous and Crystalline Aluminum Oxide Layers</li><li>Sliding Wear of Composite Stainless Steel Hardfacing under Room and Elevated Temperature</li><li>Prediction of Abrasive Erosion Impact Wear of Composite Hardfacings</li><li>Influence of Air Plasma Spraying Process Parameters on Ceramic Layer in Thermal Barrier Coatings<i></i></li><li>Evaluation of Residual Stresses in PVD Coatings by Means of Strip Substrate Length Variation and Curvature Method of Plate Substrate</li><li>Wear Rate of Nanocrystalline Diamond Coating under High Temperature Sliding Conditions</li><li>Comparative Study of Adhesive Wear for CoCr, TiC-NiMo, WC-Co as Potential FSW Tool Materials</li><li>Dependance of Wear of Cu-Cr-S Alloy on Hardness and Electrical Conductivity in Sliding Electrical Contact</li><li>Development of Impact Energy Distribution of Various Abrasives during Cyclic Impact/Abrasion Testing</li><li>The Influence of Process Parameters on Structure of Ceramic Coatings Deposited by PS-PVD Method</li><li>Non-Destructive Testing of Joints of Antifriction Parts Crimped by Pulsed Magnetic Deformation</li><li>Anti-Irradiation and Wear Resistance of Polyimide Composites</li></ul>