Progresses in Fracture and Strength of Materials and Structures

<ul><li>Interface Strength of Low-Dimensional Nano-Components</li><li>Metal Working and Dislocation Structures</li><li>Shape Prediction of Fatigue Crack Based on a Given Stress Intensity Factor Distribution</li><li>Fatigue Damage Accumulation of Welded Bridge Member during Crack Growth Propagation with Initial Crack</li><li>Physical Models for Cleavage Fracture at Various Temperatures</li><li>Study on Fracture Mechanisms of TiAl Alloys by In Situ Tensile Tests</li><li>Dynamic Analysis of Antiplane Crack under SH-Waves in the Functionally Graded Materials</li><li>Mode III Yoffe Dynamic Crack Problem on the Interface between Dissimilar Materials</li><li>Morphology Evolutions of the Short Fatigue Crack Propagation of 1Cr18Ni9Ti Weld Metal</li><li>The Grain Size and Porosity Dependent Constitutive Modeling for Nanocrystalline Ceramics with Small Plastic Deformation</li><li>Study on Impact Fatigue Life of 42CrMo Steel with M+F Dual-Phase Structure</li><li>Thermal Shock Properties of Ternary-Boride-Based Cladding Material</li><li>Fatigue Reliability Research on RD₂Axle of Railway Freight Car</li><li>Reconstruction of the Material Probabilistic S-N Relations with Given Confidence</li><li>Study on Complete Stress-Strain Experiment and Destruction Characteristics of Rock under Lower Confining Pressure</li><li>Three-Dimensional Elastic Stress Fields of Finite Thickness Plates with Elliptical Hole</li><li>Failure Analysis of Outer Swirls in the Fuel Nozzle</li><li>A New Model of Stochastic Crack Growth under Random Loading and Reliability Analysis of Fatigue Life</li><li>An Effective Energy Criterion on Fatigue Crack Growth of Metal Materials</li><li>The Evaluation of Fretting Fatigue Behavior in Room Temperature for INCOLOY Alloy 800</li><li>Effect of High Tensile Pre-Strain on the Torsional Fatigue Properties of a Structural Steel</li><li>Failure Assessment Diagrams of Semi-Elliptical Surface Crack with Constraint Effect</li><li>Contact Damage and Strength Degradation in Nitrided Pressureless Sintered (NPS) Silicon Nitrided Ceramics</li><li>The Variation of Crack Energy Density (CED) on Creep Crack Growth</li><li>Dynamic Fracture Behavior of Magnesium Alloy</li><li>Fatigue Properties of Nanometer-Scale Copper Films</li><li>High Speed Fracture Phenomena in Dyneema Composite</li><li>Fatigue Properties of Ni-Base Superalloy in Long Life Region</li><li>Assessment of Fatigue Life for High-Temperature Pipeline Welds Using X-Ray Diffraction Technique</li><li>Effect of Contact Pressure and Cyclic Stress Amplitude on Fretting Fatigue of 45-Carbon Steel</li><li>Room Temperature Creep and its Effect on Fatigue Crack Growth in a X70 Steel with Various Microstructures</li><li>A Study on Fatigue Behavior of SM490A Steel under Low Temperature</li><li>Plastic-Factor for the Fracture Toughness Test of the SA508Cl.1a Narrow-Gap Welding Part </li><li>Fatigue Life Estimation of Leakage for Excitation and Internal Pressure in Brazed Joints</li><li>Fatigue Crack Propagation Behavior Near Fusion Line between SA508 Steel and Ni-Based Buttering Metal</li><li>Growth Pattern Study of Closed Surface Flaw under Compression</li><li>Improvement of Fatigue Strength of Stainless Steel by Using a Cavitating Jet with an Associated Water Jet in Water</li><li>The Effect of Different Material Parameter Functions in Non-Homogeneous Regions on Eigen-Functions of Crack Tip Fields </li><li>Effect of Mean Stress on Fatigue Strength of Non-Combustible Magnesium Alloy</li><li>Influence of Testing Frequency on Fatigue Crack Growth of 6061-T6 Aluminum Alloy in Hydrogen Gas Environment</li><li>Fatigue Characteristics of Vulcanized Natural Rubber for Automotive Engine Mounting</li><li>Fracture Mechanics in Design Guidance and Practice</li><li>Effect of Water Height for Modal Characteristics of the Fuel Channel and Stiffness Analysis Using Modal Test Results </li><li>Study on Life Prediction Method for Creep-Fatigue Interaction at Elevated Temperature</li><li>The Fatigue Life Prediction of Multidirectional Laminated Composites</li><li>Effect of Shot Strip Interval and Shot Times on Laser Shot Peen-Forming with Repetition Laser Pulse</li><li>Isothermal LCF Behaviors of a NiCrAlYSi Coated Columnar-Grained Directionally Solidified Nickel Base Superalloy </li><li>Fatigue Property for the Powder Metallurgy Beryllium-Aluminum Composite Materials</li><li>Tearing Energy for Crack Growth at the Bonds of Cylindrical Rubber Bushes Subjected to Axial Shear</li><li>The Effect of Hybrid Surface Modification; Combination of Fine Particle Bombardment Treatment and Nitriding, on Fatigue Properties of Steel</li><li>Characteristics and Mechanism of High pH Stress Corrosion Cracking of Pipeline Steel X70 </li><li>Stress Corrosion Cracking of Pipeline Steel in Soil Environments of Eastern China </li><li>Influence of Loading Frequency on Fatigue Behavior of High Strength Steel </li><li>A Crack in an Electrode Layer between Two Dissimilar Piezoelectric Materials</li><li>Investigations on Fatigue Properties of Die Cast Magnesium Alloy AZ91HP at Very High Cycles</li><li>An Experimental Investigation of Interface Fracture Characteristic of APS Thermal Barrier Coating System under Bending at 1000 degreesC</li><li>Fatigue Properties of Austenitic Stainless Steel with Circumferential Notch</li><li>Ductile Crack Propagation Characteristics in Thin Steel Tubes</li><li>Experimental Study of the Effects of Surface Defects on Rolling Contact Fatigue Behavior</li><li>The Non-Local Theory Solution of a Crack in the Functionally Graded Piezoelectric Materials Subjected to the Harmonic Anti-Plane Shear Stress Waves</li><li>Crack Problem for a Functionally Graded Orthotropic Coating-Substrate Structure</li><li>Influence of Plasma Radical Nitriding on Fatigue Properties of SCM435 Steel</li><li>Effect of Physical Property of Water on SCC Growth Rate of 316L Stainless Steels in High-Temperature Water </li><li>Influence of Deposition Bias Voltage on Fatigue Cracking Behavior of Chromium Nitride Film Deposited on Steel</li><li>The Relation of the Interlaminar Fracture Toughness and the Acoustic Emission (Ae) under the Enf Test</li><li>Fatigue Lives of a Ferritic Stainless Steel Containing Deformation Twins</li><li>Shear-Type Fatigue Crack Growth in SAE52100 Steel</li><li>Effect of Extrusion Ratio on Fatigue Properties of Hot-Extruded Magnesium Alloys</li><li>Effects of Microstructures on Strength and Fatigue Properties of Long-Term-Serviced F12 Steels</li><li>Fatigue Properties of Surface-Micromachined Al-3%Ti Thin Films</li><li>Life Evaluation of a Disk Brake of Railway Vehicles Considering Pressure Distributions at a Frictional Surface </li><li>Crack Formation of Ceramic Thin Film on Polymer Substrate </li><li>Investigation of Mechanical Stability of Thermally Aged a-c:H DLC Films with Different Precursor Gases</li><li>Thermal Fatigue Properties of the Fin in the Boilers</li><li>Distributions of ?' Martensitic Phase Transformed on Fracture Surfaces of SUS 304 Stainless Steel Having Through- and Part-Through-Thickness Fatigue Cracks </li><li>An Analysis of the Fatigue Strength of Metals Containing Small Defects</li><li>Study on the Effect of Cl^- Concentration on the Corrosion Fatigue Damage in a Rolled AZ31B Magnesium Alloy by Acoustic Emission</li><li>The Method to Determine the Expression for Fatigue Curves</li><li>Effect of Fusing Treatment on Fatigue Strength of Thermally Sprayed Steels with Co-Based Self-Fluxing Alloy Coating </li><li>Pure Bending Testing of Cr-Mo Alloy in Metal Dusting Condition</li><li>Bending Strength of Al₂O₃ Ceramics for Textiles Machinery and Elastic Wave Characteristics by Wavelet Analysis</li><li>Study on Strengthening of the Solid Contact Alloy CuW80/Cu </li><li>Analyzing the Microstructure and Tensile Properties of an Al8Si0.35Mg Cast Alloy with Prolonged Aging</li><li>Effect of Solution Treatment Temperature on Properties of an Al11Si3Cu0.35Mg Cast Alloy</li><li>Theoretical Analysis and Experimental Research on the Braced Stress of Vacuum Glazing</li><li>Young's Modulus of In Situ TiB Whiskers in Ti Metal Matrix Composites</li><li>Generalized Drucker-Prager Strength Criteria </li><li>Separation of Primary Stress in Finite Element Analysis of Pressure Vessel with the Principle of Superposition</li><li>A Proposed Thickness Distribution of Elbow Resisting Ratcheting </li><li>Study on the Strength of Jointed Rock Mass</li><li>Effects of Chemical Compositions of the Submerged Arc Welding Wires on Impact Toughness of the Weld Metals for the Pipeline Steel</li><li>Stress Distribution of the Composites Reinforced by Slub-Like Short Fibers</li><li>Strength and Toughness of 1.1wt% Li-Containing Al-Zn-Mg-Cu Alloys</li><li>Experimental Studies of Non-Equilibrium Grain-Boundary Segregations of Phosphorus under Low Tensile Stresses</li><li>Influence of Residual Stresses on the Interfacial Toughness Measurement by Cross-Sectional Nanoindentation</li><li>Micorstructure and Properties of 2Cr16Ni2MoN Stainless Steel</li><li>Stress Relaxation Testing For Analysis of 12Cr1MoVG Steel for Creep Strength Evaluation</li><li>Compressive Deformation Behavior of the Ferritic Oxide Dispersion Strengthened Alloys at Elevated Temperatures</li><li>Evaluation of Critical Fracture Stress in Low Alloy Steels by Finite Element Analysis of Small Punch Test</li><li>Empirical Correlation between Parameters from Small Punch and Tensile Curves of Mn-Mo-Ni Low Alloy Steels by Using Test and FE Analysis</li><li>Structural Strength and Buckling Analysis for a Steel Derrick after its Members Removed Partly</li><li>Strengthening of Cu-Ti₂SnC Composites due to Microstructural Changes in the Material</li><li>Impact Toughness of Titanium Alloys with Different Strengthening Methods</li><li>Strength Calculation of the Screw Conveyor of a Decanter Centrifuge under Normal Operation Conditions</li><li>The Effect of Heat Treatment on the Properties of LF9 Alloy</li><li>Creep Behavior of Functionally Graded Material under In-Plane Bending Moment </li><li>Experimental Study on Residual Stress of K24 Superalloy in Laser Cladding Zone by Laser Shock Processing</li><li>Effect of Tungsten Addition on Properties of Ni-Based Alloy Sheet Prepared by EB-PVD </li><li>Influence of Oxidation to Small Punch Creep Test</li><li>Tensile Properties and Fracture Characteristics of Spray Deposited Ni₃Al-Based Superalloy(IC6)</li><li>Compressive Properties of Quartzite Microcrystallite Glass Ceramics</li><li>Finite Element Study of Factor Effects on Residual Stresses and Thermal Deformation of Brazed Plate-Fin Structure</li><li>Research on Physical Significance of the Larson-Miller Parameter and its Electron Theory for Heat-Resistant Steels</li><li>Microstructure and Tensile Properties of Oxide Dispersion Strengthened Molybdenum Alloys Prepared by Different Doping Process</li><li>Crack Growth in Stainless Steel 304 under Creep-Fatigue Loading</li><li>Effect of Microstructure on Thermo-Mechanical and Isothermal Low Cycle Fatigue Failures of a Single Crystal Ni-Base Superalloy</li><li>Residual Stress Characteristics of Plasma Sprayed CoNiCrAlY Coatings by X-Ray Diffraction</li><li>The Study on Failure Behavior and Low Cycle Fatigue Life of Hot Gas Casing for Gas Turbine</li><li>Microstructure and Strength of Oxidation-Bonded Porous Silicon Nitride Ceramics</li><li>Microstructure and High Temperature Stress Rupture Properties of Ru-Containing Directionally Solidified Ni-Base Superalloy</li><li>Microstructural Evolution during Tensile Creep of a Single-Crystal Nickel-Base Superalloy </li><li>Effect of Original Microstructure on the Hot Compression Behavior of Superalloy 718</li><li>Welding Characteristic Evaluation of GMAW and Laser Cladding for the Gas Turbine 1st Blade</li><li>A Study on the Degradation of the Superalloy Inconel 718 Using Ultrasonic Technique</li><li>Characteristics of High Temperature Tensile Properties and Residual Stresses in Welded Joints of the SM570-TMCP Steel</li><li>Creep Model Based on Theta Projection and Omega Method for Predicting the Creep Behavior of Alloy</li><li>Segregation of Alloying Elements of Directionally Solidified Nickel Based Superalloy CM247LC during Creep Degradation Process</li><li>Artificial Neural Network Models for Predicting Flow Stress and Microstructure Evolution of a Hydrogenized Titanium Alloy</li><li>Fatigue Crack Growth Rate in Low ?K Range According to the Microstructure and Temperature in P122 Alloy Weldment</li><li>Quantitative Characterization of Microstructure of Thermal Deformed TA15 Titanium Alloy by EBSD</li><li>Uniaxial Cyclic Deformation Behaviors of 42CrMo Steel with Different Heat-Treatments</li><li>Characteristics of Strength and Deformation of Inner/Outer Local Wall Thinned Straight Pipes</li><li>Comparison of the Tensile Performance of Polymer PC and PC/ABS </li><li>Microstructure Reconstruction and Numerical Simulation of Deformation in Particle-Reinforced Composites</li><li>Deformation Behavior of Metal Rubber Material</li><li>Effect of Plastic Deformation at Room Temperature on Powder RE-Chrome-Boronizing for Medium Carbon Steel</li><li>Texture Evolution of Rolled AA3003 Alloy Sheets after Annealing</li><li>Long Wavelength Buckling of Cubic Open-Cell Foams Subjected to Uniaxial Compression </li><li>Stiffness and Thermal Conductivity of Carbon Nanotube Containing Aluminum </li><li>A Thermal Damage Model of UHMWPE</li><li>Microstructure and Tensile Properties of a Mg-Zn-Y-Zr Alloy Containing Quasicrystal Phase Processed by Equal Channel Angular Pressing</li><li>An Experimental Investigation on the Tensile Behavior of Silane-Modified MMT/Epoxy Nanocomposites</li><li>Failure Analysis of Al1060 Sheets under Double-Sided Pressure Deformation Conditions</li><li>Surface Morphological Changes in CP-Ti and SUS316L under Pure Tensile Loading and Creep</li><li>Development of Constitutive Equation for Infinite Body of Impact Problem</li><li>Tensile Behavior of Photonic Crystal Fibers</li><li>Influence of Temperature and Heat-Aged Condition on the Deformation Behavior of Rubber Material Using SHPB Technique with a Pulse Shaper</li><li>EBSD Analysis and Theoretical Prediction of Twin Orientations during Compression in Mg-3Al-1Zn</li><li>Compressive Deformation of ZK60 Magnesium Alloy at Elevated Temperature</li><li>Research on the Effect of Entry Angle and Pressure-Pad Force on Deep-Draw Thermo-Rheological Forming of a TC1 Ti-Alloy Sheet </li><li>Texture Development during Cold and Cryogenic Rolling in AA 7055 Aluminum Alloy</li><li>Dynamic Restoration Process of 7050 Aluminum Alloy during Superplastic Deformation </li><li>DRX in 7050 Aluminum Alloy during Constraint Deformation Processing at High Temperature</li><li>Compressive Deformation in Aluminum Foam Investigated Using a 2D Object Oriented Finite Element Modeling Approach</li><li>In Situ Measurement of Lattice Spacing of Ternary Ni-Ti-Nb Alloys during Hydrogen Absorption</li><li>Acoustic Emission Investigation of the Anelastic Recovery Behavior of Basal Plane Textured AZ31B as a Function of Loading Direction</li><li>Formability Analysis of the Mg-Alloy AZ31</li><li>Influence of Collision Velocity and Angle on Bullet Deformation Investigated by Reconstruction and FEM Analysis </li><li>Stress-Assisted Atomic Migration in Thin Copper Films</li><li>Deformation Behavior and Strength of Beam-To-Column Connections in Steel Portal Frame</li><li>Effect of an Electric Field on the Texture and Microstructure Evolution during Annealing of High Reduction Cold-Rolled Ni</li><li>Characteristic of Deformation of Ti-6Al-4V Alloy with Hydrogen at High Temperature</li><li>Study on Cavity Growth in Uniaxial Tension of ZK60 Magnesium Alloy</li><li>High Temperature Deformation Mechanism of 7075 Aluminum Alloy </li><li>Effect of Extruding Technology on Microstructure and Properties of Al-Li Alloy</li><li>The Influence of Aging Process on Microstructures and Properties of an Al-2.54Li-1.61Cu-1.23Mg-0.22Zr Alloy</li><li>The Influence of Pre-Annealing on Recrystallization in Heavily Cold-Rolled Nickel </li><li>Deformation and Annealing Textures of Extruded and Cold Rolled Pure Ni Single Crystals of Cube Orientation</li><li>Grain Orientation Dependence of Extended Planar Dislocation Boundaries in Cold-Rolled Polycrystalline Aluminium</li><li>Researches on Microstructures and Mechanical Properties of Extruded Mg-Zn-Zr-Y Alloy</li><li>The Effect of Heat Treatment on Microstructure and Mechanical Properties of ZK60 Alloy</li><li>Research on Hot Upsetting Deformation Behavior and Dynamic Recrystallization for AZ31</li><li>The Grinding Force Measure and Analysis on the Abrasive Belt Grinding to Magnesium Alloy</li><li>The Mechanical Property and Microstructure of Ti-4Al-2V Alloy after High Speed Shot Peening Treatment </li><li>A Preliminary Model Accounting for the Suction Pressure in CMP Process</li><li>Tilt of Atomic Force Microscope Cantilevers: Effect on Friction Measurements</li><li>The Application of Wavelet Theory in Analysis of Surface Topography of Rifle Worn Marks</li><li>The Estimation of Barrel-Rifle Surface Wear Based on Fractal Theory</li><li>Nonlinear Dynamics of Mechanical Systems with Sectional Frictions</li><li>Friction Characteristics between Two Bodies under the Vibration Working Condition and their Applications</li><li>Study on Characteristics of Vibration Friction for Pile-Soil System</li><li>The Effect of the Microstructure on the Wear-Resistance in the Welding Deposited Metal</li><li>Capillary Adhesion between the Micro-Cantilever and the Substrate </li><li>Fracture Toughness Calculation by Movable Cellular Automata Method</li><li>Temperature Effect on the Friction Behavior of NiTi Shape Memory Alloy</li><li>Gear Abrasion-Induced System Vibration</li><li>Tribological Properties of MoS₂-Coated Gray Cast Irons with Some Different Matrix Phases under the Boundary Lubricating Conditions</li><li>Wear Mechanism of Ti(C, N)-Based Cermet Cutting Tools in the Machining of Normalized Medium Carbon Steel AISI1045 </li><li>Influence of Laser Micro-Mesh Texturing on the Tribological Performance in an EHL Point Contact</li><li>Reciprocating Triboligical Behavior of PA1010 Filled with ZnOw</li><li>Unequal Interval Grey Forecast of the Rate of High Temperature Abrasion of Water-Wall Tubes in Circulating Fluidized Bed Boilers </li><li>Research on Nano-Mechanical and Micro-Tribological Behaviors of C⁺- Implanted Silicon</li><li>A Study on Diffusion Wear of Machining Tool and Simulation by Diffusion Couple</li><li>Analysis of Fretting Problems Using a Numerical Method Based on Cauchy Singular Integral Equation</li><li>Tribological Behaviors of Bulk Metallic Glasses</li><li>A Simulation of Hydrodynamic Lubrication on Non-Glazed Surfaces under Different Sliding Velocities and Loads</li><li>Fracture Healing in the Presence of Polyethylene Wear Debris and Oestrogen Deficiency</li><li>Effect of Tempering on the Wear Characteristics of Induction-Hardened SPS5 Steel</li><li>Effect of Sliding Speed and Applied Load on the Wear Behavior of Thermally Sprayed Ni-Based Self-Flux Alloy Coating </li><li>Sliding Wear Behavior of Al/SiC Composites Fabricated by Thermal Spray Process Against Different Counterparts </li><li>Microstructure and Wear Behavior of Thermally Sprayed Fe-Based Amorphous Coating </li><li>Tribological Behavior of Phosphor Bronze against SAE52100 Steel under Different Lubricants</li><li>Effect of Stress Relief Groove Shape on Fretting Fatigue Strength</li><li>The Rolling Contact Fatigue Wear of Nylon Composites Filled with Metal-Oxides</li><li>Stress Analysis of Bonded-Interface Technique on Subsurface Damage Observations of Brittle Porcelains</li><li>Composite Fretting Wear of Aluminum Alloy</li><li>Fretting of Human Axial Cortical Bone</li><li>Tribological Behavior of Laser-Cladding Ni60 and Co-Cr-W Coatings at Elevated Temperature</li><li>Fretting Fatigue Strength and Life Estimation Considering the Fretting Wear Process</li><li>The Contact Resistance and Arc Erosion Behavior of Separable C_P-Nb-Cr/Cu-Cd Electrical Contact Material</li><li>Compared Study on Laser Cladding and Plasma Spraying of Nuclear Valve Clacks</li><li>Sliding and Loosening Behavior of Thread Joints under Transverse Loading</li><li>Tribological Behaviour of Ceramic Coatings Formed on Titanium Alloy through Miro-Arc Oxidation Technique</li><li>An Experimental Study of Excavation Damaged Zone in Anisotropic Rock</li><li>Fatigue Analysis and Life Prediction of Dumpers with Cumulative Fatigue Damage Approach and Finite Element Model</li><li>Numerical Analysis on Surface Fractures in Two-Layered Materials Subjected to Thermal Loading</li><li>Influence of Duration of Stress Wave on the Spallation Process in Inhomogeneous Material</li><li>Three Dimensional Numerical Approach to Splitting Failure of Rock Discs</li><li>Hot Spot Stress Analysis of Fatigue for Tsing Ma Bridge Critical Members under Traffic Using Finite Element Method</li><li>Study on Dynamic Behaviors of Thin Plate Structure by DBEM</li><li>Numerical Simulation on Cracks Propagation and Coalescence Process in Rock</li><li>The Influence of Stress Ratio on the Fracture Behavior of Brittle Materials</li><li>Numerical Model for Thermal Cracking of Concrete</li><li>Digital Image Based Modeling of Rock Failure at Meso-Scale</li><li>Numerical Simulation of 3-D Failure Process of Reinforced Concrete Specimen under Uniaxial Tension</li><li>Study of Interface Problems Using Finite Element Method</li><li>Stress Intensity Determination for MSD Riveted Stiffened Panels in the Presence of Corrosion</li><li>Numerical Simulation on AE Characteristics of Rock and Concrete Materials</li><li>Atomistic Finite Element Simulations on the Tensile Properties of Polyhedral Oligomeric Silsesquioxane (POSS) Reinforced Polystyrene</li><li>Atomistic Simulation of Crack Initiation at Bi-Material Interface Edges</li><li>Fracture-Damage Model for Anchored Discontinuous Jointed Rockmass and its Application</li><li>Research on Rubbing Fault in a Dual-Disc Overhung Rotor-Bearing System</li><li>Study on the Modelling of Microstructure for Polycrystalline Materials</li><li>Modelling the Behavior of Short Fatigue Cracks under Variable Amplitude Loading Using FEM</li><li>Simulation on the Short Fatigue Crack Initiation of LZ50 Axle Steel for Railway Vehicles</li><li>Numerical Simulation on Fracture Formation on Surfaces of Bi-Layered Materials</li><li>A New Numerical Method for General Failure Probability with Fuzzy Failure Region</li><li>Improved Line Sampling Reliability Analysis Method and its Application</li><li>A Fast Approximate Method for Reliability Sensitivity Based on Markov Chain Simulation</li><li>Iterative Algorithm for Structure Reliability Analysis Based on Support Vector Classification Method</li><li>Nonlinear Finite Element Analysis of Crack Tip of Rubber-Like Material</li><li>Research of Fatigue Life Simulations Applied to Large Complex Structure</li><li>Evaluation of Cracked Beam-to-Column Connection from Brittle Failure Using Finite Element Method</li><li>Using Transfer Matrix Method and Immune Algorithm to Identify Cracks in Segmented Beams</li><li>Predictive Model Based on Genetic Algorithm-Neural Network for Fatigue Performances of Pre-Corroded Aluminum Alloys</li><li>Finite-Element Simulation and Analysis on High Velocity Impact Damage of Aircraft Panel Structure</li><li>Numerical Simulation of Pressure Grouting in Soil Nail Pull-Out Tests</li><li>Numerical Simulation of Rock Stability under Dynamic Blasting Load</li><li>Numerical Simulation of Fracture Process Zone in Concrete Tension Specimen</li><li>Numerical Studies of End Effect on Crack Propagation Behavior of Brittle Specimen Containing Pre-Existing Crack under Uniaxial Compression</li><li>On the Relations between the Threshold Values of the Fatigue Crack Growth and the Cyclic Deformation Behavior of Materials</li><li>Determination of Growing Direction of Fatigue Crack </li><li>Investigating Morphology Evolution of Damage by a Cellular Automaton Modelling</li><li>Thermal Strength Evaluation of the Super Alloy Structure with Various Thermal Insulation Performances by FEM and Stress-Rupture Experiment</li><li>Monte Carlo Simulation of Stress Corrosion Cracking in Structural Metal Materials Taking Account of Surface Crack Effects </li><li>Dynamic Analysis and Three-Dimensional Finite Element Simulation of Cracked Gear</li><li>On the Stress Intensity Factor of Cracks in Residual Stress Field</li><li>Finite Element Analysis of Blower Impeller Using Cyclic Symmetry</li><li>Discrete Dislocation Dynamics Simulation on Strengths of Dislocation Network Stacks in Multilayered Structures</li><li>Fatigue Strength of Metals Containing Inclusions and Phase Inhomogeneity</li><li>Numerical Simulation on Rolling Contact Fatigue with Dent at Rolling Surface</li><li>Numerical Investigation on the Fracture Behaviors of Three-Dimensional Functionally Graded Materials</li><li>Simulation of Deformation Behavior in Aluminum Alloys Having Bimodal Structures Based on the Theory of Crystal Plasticity Considering Dislocation Distributions</li><li>The Evaluation of the Effects of the Maximum Stress Intensity Factor for Fatigue Crack Opening Behavior by Finite Element Analysis</li><li>Numerical Simulation of Thermal Stress Field of Arc-Shaped Thermal-Protection Component</li><li>Application of Percolation Theory to Rock Damage and Fracture</li><li>Experimental Study on Forming Underground Space in Soil Using Explosive Lining Method</li><li>Analysis of Slant Surface Cracks with Step Notches Subject to Contact Loadings by a Variational Boundary Integral Method</li><li>Effects of Joint Width on Strength, Stress-Strain Curve and Strain Localization of Rock Mass in Uniaxial Plane Strain Compression</li><li>Failure Process and Stress-Strain Curve of Plane Strain Rock Specimen with Initially Random Material Imperfections</li><li>A Statistical Analysis on the Fatigue Life Characteristics of Structural Materials </li><li>Damage Analysis of Medium Carbon Steel in Low Cycle Fatigue</li><li>A Simple Plastic-Damage Model for the Cement-Soil Admixture </li><li>Generalized Thermoelastic Responses of a Piezoelectric Rod Subjected to a Moving Heat Source</li><li>A Generalized Magneto-Thermoelastic Coupled Problem</li><li>Study of Damage Mechanism on Aluminum Alloy under Two Kinds of Stress States and FEM Simulation</li><li>Geometrically Nonlinear Deformation of Circular Sandwich Plates under Transversely Non-Uniform Temperature Rise</li><li>Investigation to the Effects of Grain Misorientation on the Performance of Short Cracks</li><li>Relationship between Fracture Mechanism and Microstructure in PLA/PCL Polymer Blends</li><li>Failure Mechanism and Mechanical Characteristics of Rockmass Containing Close Intermittent Joints under Plane Stress Condition </li><li>Nonlinear Dynamics of a Spur Gear Pair with Fault</li><li>The 3D-Crack Growth Mechanism of Brittle Material under 3D Compression</li><li>Study on Micro-Mechanism of Crack Initiation and Propagation Induced by Inclusion in Ultra-High Strength Steel</li><li>Calculation and Analysis on the Thermal Damage at High Temperature </li><li>Wavelet-Based Modal Parameter Identification through Measurements for Damage Detection</li><li>Evaluation of a Strain Energy Equivalence Principle (SEEP)-Based Continuum Damage Model</li><li>The Fracture Mechanism of As-Cast and Extruded SiCp/AZ91 Composites Fabricated by Stir Casting</li><li>Effect of Residual Stress Field in Front of the Slant Precrack Tip on Bent Fatigue Crack Propagation </li><li>Estimation of the Elastic-Plastic Fracture Behavior of Fiber Reinforced MMC According to the Change of Interfacial Characteristics </li><li>Effect of Microstructure on Small Fatigue Crack Initiation and Propagation Behavior of Ti-6Al-4V Alloy</li><li>On Probabilistic Fatigue Crack Growth Behavior under Constant Amplitude Loads </li><li>A Study on the Mechanism of Small Fatigue Crack Deflection Behavior in Alpha-Brass by Means of In Situ Atomic Force Microscopy and Crystallo-Graphic Orientation Analysis</li><li>Viscoelastic Deformation of PC/ABS Alloy</li><li>Combustion Synthesis of ZrW₂O₈ and Preparation of its Composite with Near Zero Thermal Expansion</li><li>Study on Reliability Design of Fiber Wound Reinforced Plastics Pressure Vessel</li><li>Development of a New Kind of Sealing Composite Material Reinforced with Aramid and Pre-Oxidized Fibers</li><li>Uniaxial and Multiaxial Cyclic Deformation Behaviors of SiCp/6061Al Alloy Composites</li><li>Study on the Fracture Energy and Fracture Toughness of the Polypropylene Fiber Reinforced Concrete</li><li>Fabrication and Properties of a Novel Anti-Radiation BaPb_0.6Ce_0.4O₃/Al Composite</li><li>Effect of Mechanical Activation on the Morphology and Microstructure of Ni-Al-Ti-B Composite Powders</li><li>Finite Element Analysis about Effects of Particle Size on Deformation Behavior of Particle Reinforced Metal Matrix Composites</li><li>Effect of Mg-Based Spherical Quasicrystals on Microstructure and Mechanical Properties of ZA85 Alloy</li><li>Analysis and Design of Curved Laminated Composite Panels under External Pressure </li><li>Investigation on the Primary Si Phase Solidification and the Properties of SiC_w/Al-18Si Composites</li><li>Effect of Interphase on Properties of Reaction Sintering C_f/SiC Composites</li><li>Influence of Extrusion Temperature on Microstructures and Mechanical Properties of Bi₂O₃-Coated Al₁₈B₄O₃₃ Whisker Reinforced Al Composites </li><li>Effect of Temperature on Strain Softening Behavior of Composites with Small Misaligned Whiskers</li><li>Measurement of Delamination Strength of Thermal Barrier Coating at High Temperature by Edge-Indent Test</li><li>Analytical Solutions for Residual Stresses of Functionally Graded Medium with Inhomogeneity</li><li>Damage Monitoring of Thick CFRP Beam Using Electrical Impedance Changes</li><li>Biodegradable Composites Based on Polylactic Acid (PLA) and China Jute Fiber</li><li>Free Vibration of Composite Annular Plates Embedded with SMA Fibers in the Circumferential Direction</li><li>Formation of C_f/C Composites with SiC Concentration Gradient on the Surface by SHCLD Technique</li><li>Effects of Polarization Treatment on Mechanical Properties of Al₂O₃/LiTaO₃ Composite Ceramics </li><li>Microstructure and Hardness Performance of a SiCp/Al Composite by Pressureless Infiltration Technique</li><li>Effect of Heat-Treatment on the Mechanical Properties of TiB_2P/2024Al Composite</li><li>Influence of Nowonty Phase on the Fracture Toughness of SiC/MoSi₂ Composites </li><li>Statistical Damage Detection of Laminated CFRP Beam Using Electrical Resistance Change Method</li><li>Effect of Solution Treatment on Tensile Properties of AA2024 Matrix Composite Reinforced with Magnesium Borate Whisker</li><li>Laser Processed Intermetallic Matrix Composite Coatings on Ni-Based Superalloy Substrate</li><li>Effect of ECAP on the Microstructure and Tensile Property of SiCp/AZ91 Magnesium Matrix Composite</li><li>Experimental Study on the Mechanical Properties of Metal Oxides Filled PA1010 Composites</li><li>Mechanical Alloying Influence on the Sintering of Cu-Fe Compound Powders</li><li>The Action Mechanism of Preparation of Calcium Carbonate/Titanate Composite Material by Mechano-Activated Method</li><li>Preparation of Characterization of Calcium Carbonate/Titanate Composite Material by Mechano-Activated Method</li><li>The Spectroscopy Characterization of Kaolinite-Organic Intercalation Materials</li><li>The Kinetic Analysis of Thermal Decomposition of PMMA/MMT Nanocomposites</li><li>Some Crystallographic Features of the Boron-Doped Diamond Single Crystals Synthesized by Fe-Ni-C-B System under HTHP</li><li>Fabrication and Mechanical Properties of Carbon Nanotubes/Epoxy Resin Composites Prepared by a Sonication Technique</li><li>Fracture Characteristic of Mg-Al-Zn-Al₂O₃ Composites</li><li>FRP Fracture Simulation Using Parallel Processing on a PC Cluster</li><li>Time-Temperature-Stress Equivalence Applied to Accelerated Characterization of Creep Behavior of Viscoelastic Polymer</li><li>Microstructure and Mechanical Properties of High Strength Al₂O_3p/6061Al Composites</li><li>Effects of Packing Density of Micropowders on the Compressive Strength of Cement Pastes</li><li>Influences of Micropowder Gradation on Rheological Properties of Cement-Based Composite Pastes</li><li>Mechanical Properties of SiC_p/Cu Composites Prepared by Electric Conduction Sintering</li><li>Stress-Strain Response in SiC/SiC Composites under Cyclic Loading</li><li>Study on Solvent Debinding Process of Powder Injection Molded Ti(C, N)-Based Cermets</li><li>Preparation of Novel Aluminum Hybrid Composite Containing Aluminum Borate Whiskers and Carbon Nanotubes</li><li>Modeling and Testing Strain Rate-Dependent Tensile Strength of Carbon/Epoxy Composites</li><li>Diagnostic Method for Delamination Monitoring of CFRP Plate Using Kriging Interpolation Method</li><li>Monitoring of Delamination of the CFRP Beam by the Smart Structure System Using the SI-F Method</li><li>Influence of Mischmetal on Performance of Copper Based Electric Contact Materials</li><li>Stress Field of Fiber-Reinforced Composites with Graded Interphase</li><li>Microstructure Formation Mechanism of (Al₂O₃+TiB₂+Al₃Ti)/Al Composites Fabricated by Reactive Hot Pressing</li><li>An Experimental Investigation on Composites Through-The-Thickness Stitched Foam Core Sandwich Panels</li><li>Mechanical Properties of (Al₂O₃+Ni) and (Al₂O₃+Ni)/Ni Laminated Materials</li><li>Study on Process Parameters of Multi-Factor Coupling Fields CVI</li><li>Influence of Fiber Orientation and Volume Fraction on Tensile Strength and Fatigue Life of CARALL Hybrid Composite</li><li>Mechanical Properties of High Reinforcement Content TiB_2p/Al Composites under Quasi-Static and Dynamic Loading</li><li>Mechanical Force Induced Grafting Effect on Strengthening HDPE/GF Composites with Maleic Anhydride</li><li>Fabrication and Dynamic Mechanical Properties Offly Ash/Epoxy Composites</li><li>Mechanical Properties of Interpenetrating Graphite/2024Al Composites Produced by Improved Squeeze Exhaust Casting</li><li>Flexural Strength of Superfine Grained Si₂N₂O-Si₃N₄ Composites</li><li>Thermal Physical Properties of Bulk Materials from ZrO₂ Nanoparticles by Sintering Process</li><li>Synthesis and Magnetic Properties of Polymer Derived Metal/SiCN Ceramic Composites</li><li>Microstructure and Mechanical Properties of 2D Tyranno SA/SiC Composites by Hot Pressing</li><li>The Micromechanical Stress Field of Cermets Composite Containing Interfacial Arc-Microcracks</li><li>Influence of Sintering Aids on the Nitridation of Reaction Bonded Si₃N₄/BN Ceramics</li><li>In Situ Combustion Synthesis of h-BN-SiC High-Temperature Ceramics</li><li>BBPPAmorphous Si-B-C-N Ceramics Fabricated by High Energy Ball Milling and Hot Pressing</li><li>Internal Friction of a 2D-C/SiC Composite from 25 degreesC to 400 degreesC</li><li>Electrically Nonlinear Fracture Analysis of Piezoelectric Materials Based on CED (Crack Energy Density)</li><li>Synthesis and Properties of AlN-SiC-TiB₂ Ceramics by SHS-HIP </li><li>Investigation on Large-Sized Sapphire Crystalline Perfection by X-Ray Double-Crystal Diffraction Method</li><li>In Situ Toughened ?-Sialon Ceramics Doped with Lutecia and Ytterbia</li><li>Influence of Nano-Silica on Microstructure and Mechanical Properties of SiO₂/BN Ceramics </li><li>Microstructures of ZrO₂(3Y) Ceramics after Dynamic Impact</li><li>Glass-Forming Ability, Interface Joint Strength and Thermal Properties of Sealing Glasses for SOFC</li><li>Influence of 3Y-TZP on Microstructure and Mechanical Properties of Al₂O₃-Based Composites</li><li>Effect of Electromechanical Loadings on Fracture Strength of Piezoelectric Ceramics</li><li>Effects of Notch Size on Strength Distribution of Ceramic Components</li><li>Effects of Particle Distribution on the Residual Thermal Stresses of (W,Ti)C/SiC/Al₂O₃ Ceramic Composite</li><li>Bi-Axial Flexure Strength, Weibull Modulus and Fracture Mode of Alumina Glass-Infiltrated Core/Veneer Ceramic Composites</li><li>Fabrication and Microstructure of SrBi₂Ta₂O₉ Ceramic</li><li>Mechanical Properties of ZrB₂-Based Ceramics Reinforced by Nano-SiC Whiskers</li><li>Analysis of a Thin Electrode Layer between Two Dissimilar Piezoelectric Solids </li><li>Effect of Sintering Process on Fabrication of Porous Si₃N₄/SiC Composites </li><li>Microhardness and Machinability of Fluorphlogopite-Mullite Glass-Ceramics</li><li>Tribology of Titanium Boride Sliding against Silicon Carbide at Elevated Temperatures </li><li>The Group Velocity Change in the Unidirectional Composite Materials </li><li>Effects of Preparation Processing on Mechanical Properties of TiAl Intermetallic</li><li>Influence of Y and Ba on Microstructure and Mechanical Properties of AZ91 Magnesium Alloys</li><li>Research on Weldability for Dual-Phase Steels Using Servo Gun Spot Welding System</li><li>Effect of Annealing Temperature on Microstructure and Properties of Surface Nanocrystalline Structure in Low Carbon Steel Specimen</li><li>Ageing Processes of Li-Containing Al-Zn-Mg-Cu Alloys</li><li>Microstructural Evolution of Inconel 690 Alloy for Steam Generator Tubes</li><li>Study on Pressure Variations in the Mold of Magnesium Alloy Die Castings</li><li>High Dense Compressive Residual Stress Produced in Laser Shock Processing on Ti6Al4V Alloys</li><li>Study on High Performance Warm Compacted Fe-2Ni-2Cu-1Mo-1C Powder Metallurgy Materials</li><li>Nickel Silicides Synthesized by High Energy Ball Milling</li><li>Study on the Microstructure and Properties of Prehardened Plastic-Mould SWFT Steel for Big Section</li><li>Uniform Design and its Application in the Chemical Composition Design of Hot Work Die Steel</li><li>Microstructure of Fe-Based ODS High-Temperature Alloy Sheet Prepared by EBPVD</li><li>Effect of Hot Treatment Process on High Performance Alloy Spring Steel D701 Mechanics Properties</li><li>Investigation of the Anti-Corrosion Ceramic Coating Formed on AZ91D Magnesium Alloy by Micro-Arc Oxidation</li><li>Tensile Properties and Fatigue Strength of Ultrafine Grained Pure Copper </li><li>Precipitation Behavior of Warm-Rolled Ti-Stabilized Interstitial-Free (IF) Steel Sheets</li><li>Mechanical Properties and Microstructures of Ferritic-Rolled Ultra-Low Carbon (ULC) and Ti-Stabilized Interstitial-Free (Ti-IF) Steels</li><li>Thermodynamic Analysis of EB-PVD Preparing SiC Coating</li><li>Investigation on Residual Stress and Crystallographic Texture of YSZ Films Prepared by EB-PVD</li><li>Simulation on Temperature Distribution in Chemical Mechanical Polishing</li><li>The Improvement of Corrosion Resistant for the Cf/Al Composites by Ni-P Coatings</li><li>HA Active Coating on Titanium Prepared by Spark Plasma Sintering </li><li>A Theoretical Model for Squeeze Film Dampers Operating with Air Entrainment</li><li>Fractal Features of Surface Morphology of Uneven Eroded Hot-Dip Galvanized Steel</li><li>Study on the Carbides and the Interface Bonding in Surfacing Welding Metal </li><li>Development of Coating Material by In Situ Reaction Synthesis</li><li>The Microstructure and Mechanical Properties of Ti/TiN Multilayer Film Synthesized by Unbalanced Magnetron Sputtering Deposition on 17-4PH Stainless Steel</li><li>Prevention of Stress Corrosion Cracking in Welded Joint of Type 304 Stainless Steel by Laser Peening</li><li>Study on Surface Metallurgy High Speed Steel Using Double Glow Plasma Technique</li><li>Preparation and Wear Resistance of TiN/Ti Deposition and Diffusion Multi-Layers by Plasma Alloying Process</li><li>Microstructure and Properties of Ni₃ (Si, Ti) Intermetallic Cladding with Nb Addition</li><li>Microstructure and Properties of Low Temperature Deposit Cr_xN Using Unbalanced Magnetron Sputtering</li><li>Microstructure and Optical Properties of Ag/TiO₂ Multilayers</li><li>Mechanical Properties of Coil Coating Evaluated with Dynamic Mechanical Analysis in Daul Cantilever</li><li>Study On the Corrosion Resistance Properties of the Ceramic Coating Obtained Through Microarc Oxidation on the Aluminium Alloy Surface</li><li>Study on Properties of Plasma Sprayed CoCrAlYCoating on TiAl Alloy Surface</li><li>Plasma Surface Alloying Process of a Fe-W-Mo-Co Surface Age Hardening High Speed Steel</li><li>Microstructure and Hardness of the Laser Surface Treated Titanium</li><li>A Special Method to Evaluate the Strong Adhesion between Brittle Coating and Ductile Substrate</li><li>Coating Influence on Residual Stress in Laser Shock Processing</li><li>Influence of Ceria on Characterization of Films Prepared by Vapor Deposition of Quasicrystal</li><li>Application of Wear Resistant Coating Technology on Coating Blade</li><li>Research on High Temperature Anti-Abrasion Protection Technology of Thermocouple Cannula</li><li>Study of New Metal/Ceramic Cored Wires </li><li>Plasma Nitriding Behavior of 1Cr18Ni9Ti Stainless Steel with Nanocrystalline Surface Induced by SMA</li><li>Thermal Vibration of Functionally Graded Circular Plates</li><li>Tribological Behavior of DLC Films by RF-PECVD at the Elevated Temperature</li><li>Friction and Wear of Lubricated Sliding Surfaces of Coated Vane and Flange in Rotary Compressor with Carbon Dioxide as a Refrigerant</li><li>CrN Coating on Magnesium Alloy AZ91 by Arc-Glow Plasma Depositing Process</li><li>Electrochemical Corrosion Behaviors of Ti₂AlNb with Double Glow Plasma Surface Molybdenized</li><li>Research on Surface Low Alloy HSS by Plasma Surface Metallographic W, MO, C Alloying</li><li>Some Problems on Evaluating Elastic Modulus of APSed Ceramic Top Coat for TBCs by Indentation Method</li><li>Collaboration Tasks on Physical and Fundamental Properties of Plasma Sprayed Thermal Barrier Coatings in Japan Society of Materials Science </li><li>Mechanical Properties of 316L Stainless Steel with Nanostructure Surface Layer Induced by Surface Mechanical Attrition Treatment</li><li>Evaluation of Silica Content on Fracture Toughness of PI/SiO₂ Hybrid Films </li><li>Oxidation Resistance of Ti-6Al-4V by Plasma Niobium Surface Alloying </li><li>The Processing of Anti-Rust Boronizing Layer on Steel Surface</li><li>Colossal Magnetoresistance Effects of La_1-xSr_xMnO₃</li><li>Effect of R.F. Power on Structures and Properties of Amorphous Fluorinated Carbon Films Prepared by PSII</li><li>Molecular Dynamics Simulation of Exit Fracture in the Case of Nanometric Cutting Process</li><li>Surface Plasma Molybdenized Burn-Resistant Titanium Alloy</li><li>Study of Delamination of Thin Film Coating on Cyclic Nano-Indentation Test</li><li>Processing of Environment Protective Phosphating and its Coating Properties</li><li>Synthesis of Boron Carbonitride Films by Plasma-Based Ion Implantation </li><li>Influence of Temperature on Characteristics of TiAl Plasma Surface Niobiumizing </li><li>Finite Element Study of the Creep Size-Effect in Thin Metal Films </li><li>Surface Morphology, Crystal Orientation and Scratch Properties of Au/NiCr/Ta Multi-Layered Metallic Films </li><li>Microstructure and Resistivity of Low Temperature Deposition ITO Films on PET Substrate by Magnetron Sputtering</li><li>XPS Analysis of Silicon Oxycarbide Formed on the Surface of Rf-Sputter Deposited SiC Thin Films</li><li>Effects of Dynamic Ion Mixing Coating Condition for Fatigue Properties of Stainless Steel with TiN Film</li><li>Improvement of Oxidation Property of SUS304 by Gas Barrier Coating</li><li>Study of Boron-Doped Diamond Films by Microwave Plasma CVD Method</li><li>Influence of Ion Bombardment Process on Adhesion between CrN Coatings and Aluminum Alloy</li><li>Study on Sputtering Characteristics of Ni80Cr20 Alloy Target</li><li>Microstructure and Properties of Microarc Oxidation Ceramic Coatings on Aluminum Alloy</li><li>Mo-Si-C-N Multi-Layer Anti-Oxidation Coating on C/C Composites </li><li>Development of Diamond-Like Carbon (DLC) Coating Compatible Surface by Fine Particle Bombardment (FPB)</li><li>The Research of Integral Cu-W Electric Contact by Friction Welding</li><li>Finite Element Simulation for Residual Stresses in Weling Process </li><li>Study on Al Alloy Welded Joint Performance Deterioration under Thermal Cycling Condition</li><li>Three Dimensional Monte Carlo Simulation of Grain Growth in HAZ of Stainless Steel SUS316</li><li>Static and Dynamic Force Analysis to Large-Scale Bed of Leather Cutting Machine Tool </li><li>Study on the Process Parameters of MPAW-Based Rapid Prototyping</li><li>Deformation and Fracture Behaviors in the Freestanding APS-TBC - Effects of Process Parameters and Thermal Exposure</li><li>Distributions of Residual Stresses in Diffusion Bonding of Dissimilar Materials Intermetallics TiAl to Steel 40Cr and Effect of Interlayer</li><li>Interfacial Resistance Method for Quality Evaluation of Diffusion Bonded Joints </li><li>Strength Predication for Load-Bearing Lugs of Three-Dimensional Braided Composites</li><li>Failure Assessment Diagrams of Semi-Elliptical Surface Crack with Constraint Effect</li><li>Application of Twin Laser Beam on AZ31/A5052 Dissimilar Metals Welding </li><li>Effects of Adhesive Joint on the Failure Strength Properties of Natural Fiber Reinforced Composite</li><li>Effects of Fiber Layer on Failure Strength Properties of Adhesive - Joined Natural Fiber Reinforced Composites </li><li>Effects of Chemical Composition and Welding Process on Fracture Resistance of Type 347 Stainless Steel Weld</li><li>Effects of Resistance Welding on the Failure Strength Properties of Natural Fiber Reinforced Composite</li><li>A Study on Mechanical Properties and Durability Evaluation of Structure Adhesived and Spot Welded Joints</li><li>Computer Aided Development of the Crack-Free Laser Welding Processes</li><li>An Estimation Formula of the Stress Concentration Factor of the Butt-Welded Joint</li><li>Microstructure in the Interface between CVD Diamond Thick Film and a Ag-Cu-Ti Braze Alloy</li><li>Method of Lines to Solve 2-D Steady Temperature Field of FGM</li><li>The Effects of Energy Director Shape on Temperature Field during Ultrasonic Welding of Thermoplastic Composites</li><li>Modeling of the Temperature Field during Electron Beam Welding of Aluminum Alloy by a Pre-Defined Keyhole</li><li>Cracking Resistance of Cu-Bearing Age-Hardening Steel</li><li>Microstructure and Mechanical Properties of Simulated Heat Affected Zone of an Ultrafine Grain Steel Laser Weld </li><li>Development of Cu Brazing Sheet with Cu-P Composite Plating</li><li>Effect of Properties of Underfill Materials on Thermal Stress Relief in Lead-Free Solder Joint of Chip Size Package</li><li>Influence of Content of Ni and Ag on Microstructure and Joint Strength of Lead-Free Solder Joint with Sn-Ag-Cu-Ni-Ge</li><li>A Study of Self-Loosening and Fatigue Failure of Bolted Joint under Transverse Vibration - Influences of Property Class of Bolt and Plastic Region Tightening</li><li>A Study on Friction Stir Welding with Heating of Aluminum Alloy</li><li>Crack Growth Characteristics of Pure Copper for Smart Stress Memory Patch</li><li>Microstructure and Strength of Alumina-Metal Joint Brazed by Activated Molybdenum-Manganese Method</li><li>Thermal Fatigue Mechanism of Welding Deposited Metal of Dies Steels</li><li>Fatigue Properties of a T Type Welded Joint in a Small-Sized Single Pass Boiler Header</li><li>A Representative Stress Model Removing Weld Joint Type Dependency of S-N Curve</li><li>Fatigue Durability Analysis Based on FE Modeling Support System for Arc-Welded Members in Automobile Suspension Module</li><li>Fatigue Strength Evaluation of Load-Carrying Fillet Weldments under Out-of-Plane Bending Load Using Structural Stress Method</li><li>Evaluation of Local Tensile Properties of Bi-Metallic Weld Joints by Small Tensile and Ball Indentation Tests</li><li>Effect of Residual Stress and Weld Metal on Hysteretic Behavior of a Welded Tubular T-Joint</li><li>Assessment of a New Semi-Rigid Model in Steel Beam-to-Column Connections </li><li>Study on the Evolution of Welding Residual Stress under Tension Loading Condition</li><li>A New Strategy for In-Service Inspection of Nuclear Piping Considering Piping Failure Frequency</li><li>Joining of SiC Ceramic to High Strength Graphite Using Polysiloxane with Active Additive</li><li>Heating Characteristics of Gas Tungsten Arc Welding of Copper Thick Plates with Shielding Gas of Argon, Helium or Nitrogen</li><li>Effects of the Welding Residual Stress on the Grounding Damage Analysis of a Tanker</li><li>Synthesis and Characterization of Nanosize Molybdenum Disulfide Particles by Quick Homogeneous Precipitation Method </li><li>Preparation and Characterization of Cr₂O₃ Nano-Powders by Sol-Gel Method</li><li>A Study on Concrescence of Inert Nano Bioceramic Scalpel Wounds </li><li>Fabrication and Fracture Properties of Nano-Sized HAP-TZP (3Y) Bioceramic for Artificial Joints</li><li>SEM In Situ Investigation of the Effects of Ca and Sr Additions on Cracking in Cast AZ91D Alloys at Different Temperatures</li><li>Adhesion Evaluation of Titanium Oxides Films on 316L Stainless Steel Substrate</li><li>Synthesis of SnO₂ Nanoparticles and Their Application on Gas Sensors</li><li>Ultrafine TiO₂ Powders Prepared from Aqueous TiCl₄ Solutions at Room Temperature</li><li>The Synthesis and Properties Studying of 1-D TaS₂ Nanostructure</li><li>Near Full Density Nano Iron-Based Materials by Pulse Current Sintering</li><li>Lactose Modified Chitosan Scaffold for Hepatocytes Culture</li><li>Phenomenological Study of the Size Effect on Martensitic Transformation in Nanograined Powders</li><li>Comparison of Property of Dynamic Melting-Loss H13 Steel by Different Surface Treatment</li><li>Molecular Aspect of Osteoporotic Fracture Healing</li><li>Synthesis and Characterizations of Nanocubes, Monodispersed Nanocrystals and Nanospheres of Au</li><li>Preparation and Performance under Corrosive Environment of Epoxy-Nanocomposite</li><li>Synthesis of Silicon Carbide Nanowires Doped with Al₂O₃</li><li>Preparation of Iron Oxide Nanoparticles by a Pyrosol Technique</li><li>Biomechanical Analysis on the Foot under Normal and Abnormal Gait for Orthotics Design </li><li>Effect of pH Values on Conversion of Calcite Crystals into Calcium Phosphate Phases in Buffer Solutions</li><li>Compressive Instability of Carbon Nanotubes</li><li>Effects of Temperature and Concentration on the Nano-Sized Hydroxyapatite Whisker Prepared by Chemical Precipitation Method</li><li>Mineralization of Chitosan via Alternate Soaking</li><li>Effective Structural Parameters of Armchair Carbon Nanotubes</li><li>Studying Effects of Bias Voltage on Properties, Wettability and Platelet Adhered Behavior of DLC Films Prepared By DC-MFCVAD</li><li>Development of High Technology for Improvement of Fatigue Strength in the Intervertebral Disc Herniation's Cervical Attachment System</li><li>Evaluation of Fatigue Transverse Cracking Behavior by Cooperation of Sliding Core and Endplate in Artificial Intervertebral Disc</li><li>Stress Analysis of the Swelling and Deswelling Process of Thermo-Responsive Gel </li><li>Development of Bone-Like Composite Material and its Properties</li><li>Evaluations of Elasto-Plastic Properties and Fracture Strength Using Indentation Technique</li><li>Young's Modulus of Polysilicon Thin Film Evaluated by Finite Element Analysis</li><li>Biomechanical Analysis of the Musculoskeletal System of Human Foot by Using Passive Elastic Characteristics of Joint</li><li>Mechanical Behavior during Self-Oscillating of NIPAAm-Co-(Ru(bpy)₃ Gel</li><li>The Swelling Behavior of Organoclays</li><li>Molecular Modeling of the Dimers from Cyclo-[(1R, 3S)-?-Acc-D-Phe]₃</li><li>Mechanical Properties on Nanoindentation Measurements of Osteonic Lamellae in a Human Cortical Bone</li><li>Adhesion Test of Nanostructured Materials by a Novel AFM Probe</li><li>Self-Assembly Effects of Cyclic Peptide Dimers: Molecular Modeling Study</li><li>Effects of Nitrogen Implantation on the Bonding Strength of Porcelain Fused to Pure Titanium</li><li>Nanomechanical Properties of Tooth and Bone Revealed by Nanoindentation and AFM</li><li>Research and Development of Calcium Phosphate Cement </li><li>The Quantitative Measurement Model of ACFM Based on Swept Frequency Method</li><li>Nondestructive Evaluation of the Corroded Pipe by Time-Frequency Analysis</li><li>Wavelet Analysis of Elastic Wave for Wall Thinned Inconel 690 Tube </li><li>Nondestructive Detection of a Crack in a Triangular Cantilever Beam Based on Frequency Measurement</li><li>Model Based Online Diagnosis of Rotating Machinery Structural Damage</li><li>Correlation between Crack Growth Rate and Magnetic Memory Signal of X45 Steel</li><li>Ultrasonic Fast-Identification Expert System of the Auto Stick-Weld Defect Based on Echo-Characteristics Analyzing</li><li>Experimental Investigation on Residual Stress of Model S1100 of Crankshaft Chamfer Based on XRD</li><li>Numerical Analysis of the Measuring Errors in Quantitative Detection of Defects with Shearing Speckle Pattern Interferometry </li><li>Application of Nondestructive Detecting Technology for Geological Radar in a Large-Scale Highway Lanslide Treatment </li><li>Infrared Thermal Image Study on Failure of Granite with Hole</li><li>Damage Detection Based on the Cross Correlation Function Amplitude Vector and its Application to the ASCE Benchmark Structure</li><li>Influence of Heterogeneity on Direct Tensile Failure Process of Rocks and Associated Fractal Characteristic of AE</li><li>Damage Identification of Rock Mass with Artificial Neural Networks </li><li>Experimental Study on Crack Propagation by AE Location under Uniaxial Compression Condition</li><li>Experimental Verification and Theoretical Analysis on Felicity Effect of Acoustic Emission in Concrete</li><li>Statistical Damage Detection of Laminated CFRP Beam Using Electrical Resistance Change Method</li><li>Compaction Quality of Bitumen Mixtures Based on Ultrasonic Methods</li><li>Non-Destructive Evaluation of a Delamination in Laminates by Lamb Wave Propagation</li><li>Measurement of Acoustic Impedance of Thin Polymeric Films by Acoustic Resonant Spectroscopy</li><li>Crack Growth Mechanisms from 3-D Surface Flaw with Varied Dipping Angle under Uniaxial Compression</li><li>The Crack Growth Mechanism from 3-D Surface Flaw with Strain and Acoustic Emission Measurement under Axial Compression</li><li>Quantitative Evaluation of Cracks under Water by Microwaves</li><li>A Study on the Vibration Characteristics of Symmetry and Asymmetry Laminated Composite Materials by Using ESPI</li><li>A Study of Magnetic Charge per Unit Area of Dipole Model for the NDE</li><li>Improvement of Crack Detection Probability by Using Magnetic Camera and Image Processing</li><li>Development of Signal Processing Circuit of a Magnetic Camera for the NDT of a Paramagnetic Material</li><li>Development of Numerical Analysis Software for the NDE by Using Dipole Model</li><li>Understanding and Detecting Early Stages of SCC Initiation in Sensitized Stainless Steel by Means of Electrochemical Potential Transients</li><li>Non-Destructive Evaluation of Creep Damage of Ni-Based Superalloy Using A Scanning Blue Laser Microscope</li><li>In Situ X-Ray Stress Measurement in Electrodeposited Cu Foils under Tensile and Fatigue Loading </li><li>Analysis of High Active AE Signal by Continuous Waveform Recorder</li><li>In-Process Damage Monitoring and Stress Analysis of Thermal Spray Coating</li><li>Pressurized Water Corrosion Resistance of Carbon Steels and Their Nondestructive Characterization</li><li>An Evaluation on Corrosion Effect of Carbon Steel Using the NDT </li><li>Study on Damage Mechanism of Pipe Using Ultrasonic Wave and Acoustic Emission Technique </li><li>Measurement of Residual Stress in Water Pipe Welds Using the Hole-Drilling Technique</li><li>X-Ray Stress Measurement of Fiber Reinforced Plastics Composite Material</li><li>Study on Fault Detection and Diagnosis of the Edge-Transmission Ball Mill System</li><li>Damage Detection and Quantitative Assessment for the Cracked Beam Structures </li><li>Quantitative Estimation of the Fastening Condition of a Bolt with Using Piezoceramic (PZT) Sensors</li><li>Identification of a Defect Using the Equivalent Load Method</li><li>Influence of Observation Errors on the Identification of External Loads</li><li>Analysis of Stress Intensity Factors of a Planar Rectangular Interfacial Crack in Three Dimensional Bimaterials</li><li>Coupling Analysis of Fluid Film and Thermal Deformation of Sealing Members in Spiral Groove Mechanical Seal</li><li>Reliability-Based Sensitivity Design of Beam Structure with Non-Normal Distribution</li><li>ANN-Based Crack Identification in Rotor System with Multi-Crack in Shaft</li><li>The Inhibition Effect of Imidazoline and Diethylene Triamine on the Stress Corrosion Cracking of 08Cr2AlMo Steel in H₂S Solution</li><li>Research on the Control Function and Control Arithmetic of Automobile Automatic Brake</li><li>A Method to Determine the Periodic Solution Based on Observed State Information and Nonlinear Analysis of Hydrodynamic Bearing-Rotor System</li><li>Study on Looseness and Impact - Rub Coupling Faults of a Vertical Dual-Disk Cantilever Rotor- Bearing System</li><li>Investigation on Levitation and Restitution Mechanisms of FPD Air Handling System </li><li>Probabilistic Cyclic Constitutions and Design Curves of 0Cr18Ni10Ti Pipe Steel</li><li>Statistical Reconstruction of the One-Dimensional Mechanical and Fatigue Strengths</li><li>A Statistical Load Weighted Average Fatigue Reliability Model for Uncertain Constant Amplitude Cyclic Load</li><li>Stability of Two-Span Rotor-Bearing System with Coupling Faults of Crack and Rub-Impact</li><li>Correction on Parameters in Torsion Vibration Model for Turbine-Generator Shafts </li><li>Stability Analysis of Cut Rock Slope with Reinforcement by Steel Cables</li><li>Effects of External Loads on the Reliability of Welded Pipe with Circumferential Crack</li><li>One Method of System Analysis Based on Some Parameters in the Underground Chambers and Application</li><li>Reliability Analysis of Railway Tunnel Construction Process within Soft and Weak Rock Mass Using the Unified Elasto-Plastic Strength Criterion</li><li>A New Concept for Assessing System Reliability Based on Probability Decomposition Method</li><li>Mechanical Reliability of a Segmented Silicon Layer on Ultra-Thin Polyimide Substrates </li><li>The Relation of the Geometric Parameters to the Maximal Principal Stress of Crankshaft</li><li>Analyzing the Strength and Stability of Large Underground Cavern Group with Different Generator Socket Construction Schemes Based on Three Dimensional Numerical Simulation </li><li>Reliability Analysis for Rotor-Stator Systems with Rubbing</li><li>First Passage of Uncertain Nonlinear MDOF Systems with Uncorrelated Failure Modes</li><li>Study on the Relationship of Hydrogen Content and Ultrasonic Propagation Properties</li><li>Influence of Different Loading Modes on Rock Tensile Strength</li><li>Fuzzy Method to Determine Probability Distribution Type of Fatigue Crack Data</li><li>Effects of Various Types of Distribution on Probabilistic Method and FAD </li><li>Experimental Study on Cracking and Integrity Stability of Xiluodu Arch Dam</li><li>The Safety Assessment of Wheelchair Occupants in Road Passenger Vehicles in a Frontal Crash: A Computer Simulation</li><li>Study on the Mechanical Bend Fatigue of Micro-Joining Soldered Joint with Lead-Free Solder </li><li>Expansion Behavior of Portland Cement Mortars under Sulfate Attack </li><li>A Study on the Static Buckling Load Estimation of the Spacer Grid in the Pressurized Water Reactor Fuel Assembly</li><li>Precision Diagnosis of Electric Multiple Units for Performance Evaluation</li><li>Optimal Placement of Multi Circular Heat Sources of HANARO Irradiation Test</li><li>Comparison of Reliability of Solder Joints by FORM and SORM</li><li>Damping Analysis of Asymmetrical Comb Accelerometer</li><li>Safety Evaluation of Pressure Piping with Weld Flaw after Long Time Service in a Water Power Plant</li><li>Research on Crack Measurement Technique in Solids Material with Digital Image Correlation (DIC)</li><li>Corrosion Behavior of Thixoformed AZ91D Magnesium Alloy in NaCl Aqueous Solution</li><li>Corrosion of 16Mn in High Pressure Carbon Dioxide Saturated NACE Solutions with Hydrogen Sulfide</li><li>Study on Reliability Analysis of Tailings Dam Stability</li><li>Risk Based Approach of In-Service Inspection and Maintenance for Petrochemical Industries</li><li>Fault Diagnosis Expert System Integrated Developing Environment Based on CLIPS</li><li>Status Monitoring and Fault Diagnosis Network System Based on UPnP</li><li>Resonance Reliability Assessment of Turbine Blade with Parametric Uncertainty</li><li>Heat-Aging Effect on the Material Properties and Useful Life Prediction of Rubber Materials</li><li>Creep Life Prediction of Waspaloy Using the Initial Strain Parameter Technique</li><li>Evaluation of Drop Impact Load for Thin Cone-Shaped Structures</li><li>Increasing Damping Ratios in a Tuned Liquid Damper Using Damping Bars</li><li>Influence of Tapered Cross Section on Fatigue Damage of Cladding Fasteners on Side Faces of Tall Buildings</li><li>Influence of Non-Gaussian Local Wind Pressures on Fatigue Damage of a Cladding Fastener on a Side Face of a Tall Building</li><li>Stress Analysis of Automotive Engine Cover under Static and Vibration Load </li><li>Impact Analysis for the Egg-Crate Structure of a Nuclear Fuel Assembly by Using FEM</li><li>Structural Response and Behavior Analyses of Steel Joint Components at Elevated Temperatures</li><li>Numerical Simulation of Deformation and Strength of Reinforced Concrete Slabs under Thermal-Mechanical Loads</li><li>Fracture Characteristics of a Hybrid Composite Joint Beam for the Tilting Car Body under Static and Fatigue Transverse Loads</li><li>A Simple Spline Integral Equation Method for Circular Plates with Variable Thickness</li><li>Design Technology of ?-Shaped Seal Ring Based on Plastic Limit Analysis</li><li>Uniform Wearing Optimum Design of Extrusion Die Profile </li><li>A New Numerical Method for Axisymmetrical Bending of Circular Plates with Large Deflection</li><li>Stability Analysis on Surrounding Rockmass of Deep Tunnel Based on YAI and FD Concepts</li><li>12Finite Element Analysis of an Automobile Clutch System</li><li>Prediction of Cutting Chatter Based on Hidden Markov Model</li><li>An Integrated Neural Classifier for Stream Turbine Damage Identification Based on PSO</li><li>Nonlinear Response of Clamped Circular Plates Subjected to Transverse Excitation Load</li><li>The Application of ISDG Method on the Mechanical Property Measurement of the Welding-Line Material </li><li>Structural Strength Evaluation of a Carbody by Finite Element Analysis and Load Test</li><li>Effect of Nonlinear Shear Strength Characteristic on the Slope Stability of Super High Rockfill Dam</li><li>Wetting Effects of Rockfill on the Deformation of the Yellow River Xiaolangdi Dam</li><li>Performance Evaluations of the 3^rd Rail Type Power Collector for Rubber-Tired Vehicles</li><li>Fatigue Properties of Spherical Graphite Iron Crankshafts</li><li>Calculation of Dynamic Parameters of Elastic Thin Plates under Blast Loading</li><li>Application of the Rubber Panel Structure for Railway Crossings</li><li>Application of Distance Evaluation and its Improved Algorithms in Engineering Materials Selection</li><li>On Stress Concentration Character at the Abnormal Cross-Section of the Concentric Shaft with Bigger Diameter Ratio</li><li>Analysis of Performance Characteristics in Deteriorated Subway Rolling Stock</li><li>Application of Data Mining Technology in Structural Strength Design</li><li>The Microstructures and Catalysis of Metallic Films Covering Diamond Single Crystals Synthesized from Fe-Ni-C System</li><li>Design of a Novel Micromachined Gyroscope with Compensatory Capacitance</li><li>Effects of Phase-Equilibrium Temperature and Pressure on the Thickness Decision of a Methane Hydrate Container</li><li>Fatigue Assessment for Ship Structure Acted on Non-Linear Wave Loads</li><li>Quantitative Analysis of Transmission Shafts after Torsion Fatigue Test</li><li>Wavelet Denoising of the Horizontal Vibration Signal for Identification of the Guide Rail Irregularity in Elevator</li><li>An Enhanced Pre & Post Processing Technique for the Three Dimensional Tunnel Analysis: Tunnel Modelling Wizard </li><li>Development of 3-Axis Load Cell for Measuring the Side-Force of the Rear Damper of MPV</li><li>Fatigue Design of Gas Welded Joint for the Railroad Car Body Using the Hot Spot Stress</li><li>Fatigue Design of the Railroad Car Body Member Using a Simulated Single Spot Welded Joint</li><li>Square-Structure Estimation of Bolt Fastening Conditions with Using PZT Patches</li><li>Structural Analysis of Boom System in 42m Aerial Platform Truck</li><li>Mechanical Behaviors of a Power Steering Hose Assembly during the Swaging Process</li><li>Codes and Practice of Fatigue Design for Welded Structure</li><li>Development of a Material Mixing Method for Topology Optimization of a Structure with Multiple Thermal Criteria</li><li>Optimum Design of a Dynamic Micro-Mixer for Multiphase Flow</li><li>Optimum Design of a Planar Micromanipulator Using Displacement Amplifier</li><li>Axiomatic Design of a Spatial Micromanipulator and Experimental Verification</li><li>Topology Optimization of the Inner Reinforcement for a Vehicle's Hood Using Smoothing Scheme</li><li>Optimization of Materials and Modal Analysis for Motorcycle Frame</li><li>Structural Stability Evaluation for Lifting Lug Design of Large Marine Engine by Finite Element Analysis</li><li>Static and Fatigue Analysis of a Hybrid Joint Part for the Tilting Car Body </li><li>Degradation and Failure Mechanisms of EPDM Rubbers for Automotive Radiator Hoses</li><li>Thermal Deformation Analysis of Copper Microbridges with Speckle Interferometry and Finite Element</li><li>The Mechanisms Analysis of the ACF Bonding Strengths after the High Temperature/ Humidity Environment Test</li><li>Effects of Nano Fillers on the Conductivity, Adhesion Strength and Reliability of Isotropic Conductive Adhesives (ICAs)</li><li>Microstructure and Mechanical Properties of High Densification Mo/Cu Composites </li><li>Microstructure and Properties of Environmental-Friendly Sip/4032Al Composites Used for Electronic Packaging</li><li>A Study on Failure Prediction of Airborne Electronic Equipment</li><li>Study on the Service Life of Electronic Equipment</li><li>Thermal Stress Distribution in the Corner of IC Package Structure</li><li>Thermal Stress Analysis of MCM Package Using Diamond Material</li><li>Torsional Fatigue of 63Sn-37Pb and Sn-0.7Cu Solders</li><li>Research on Creep Properties of Sn2.5Ag0.7CuXRE Lead-Free Soldered Joints for Surface Mount Technology</li><li>In Situ Thermal-Mechanical Fatigue Testing of Thin Au Lines</li><li>Theoretical Analysis of Young's Modulus and Dielectric Constant for Low-k Porous Silicon Dioxide Films</li><li>Micro/Nano Film Getters for Vacuum Maintenance of MEMS</li><li>Isothermal Aging Effects on the Microstructure, IMC and Strength of SnAgCu/Cu Solder Joint</li><li>A Comparative Study of the Solder Joint Reliability in Flip Chip Assemblies with Compliant and Rigid Substrates</li><li>Behavior of Anisotropic Conductive Joints under Hygrothermal Conditions</li><li>Interface Cracking of Plastic Electronic Package under Temperature and Humidity Environment</li><li>Shape Prediction and Reliability Design of Ball Grid Array Solder Joints </li><li>Low-Temperature Sintering of Nanoscale Silver Paste for Large-Area Joints in Power Electronics Modules</li><li>Fluctuation Mechanism of Mechanical Properties of Electroplated-Copper Thin Films Used for Three Dimensional Electronic Modules</li><li>Threshold Current Density of Electromigration Damage in Angled Polycrystalline Line</li><li>Crack Propagation Behavior at Sn37Pb-Copper Interface in Low Cycle Fatigue</li><li>Hardness and Elastic Modulus of ZnO Thin Films Fabricated by PLD Method</li><li>On Using Discrete Particle Approaches for Simulating the Perforation Process of Concrete Slab by Hard Projectile</li><li>Fractal Characterization of Sealing Surface Topography and Leakage Model of Metallic Gaskets</li><li>Effect of C/Ti Ratio and Al Powder Size on Microstructure and Performance of Al-Ti-C Grain Refiner</li><li>The Analysis to the Correlation between Cooling Medium and Cooling Result of DWTT Specimen</li><li>Effect of Spring Pressure on Basic Performance of Contacting Mechanical Seals</li><li>Finite Element Analysis of Dongjusi Railway Tunnel within Hard Rock Mass Based on the Unified Rock Mass Strength Criterion</li><li>Analysis of Valence Electron Theory on the Catalytic Mechanism of Diamond Single Crystal Growth</li><li>Exact Relationships between Eigenvalues of FGM Circular Plates Based on RPT and those of Isotropic Homogeneous Circular Plates Based on CPT</li><li>Application of Innovative GFRP Pipe Soil Nail System in Hong Kong </li><li>The Abnormal Viscosity Variation Behavior of Melt Bi</li><li>Modeling of the Effect of Excavation Mode on the Extent of the Anisotropic Zone Surrounding Deep Tunnels</li><li>Effect of Rotation to a Half-Sapce in Magneto-Thermoelasticity with Thermal Relaxations</li><li>Analysis on the Gravel Stratum Deformation by Dewatering</li><li>Study on the Electrochemical Behavior of the Weldment for SPV50Q Steel in H₂S-Containing Environment</li><li>Evaluation of Stress Corrosion Cracking of Type 304L Stainless Steel in Low Concentration Sodium Hydroxide Solution with High Temperature</li><li>Research on the Non-Contact Manipulation of Biomaterials in the Stationary Sound Field of Ultrasonic Transducers</li><li>Application of Superelasticity of SMAs in Bolted End-Plate Connection</li><li>Crystal Structure of the New Compound NdFeSb₃</li><li>The Deformation of Discontinuity in the DDA Method</li><li>Investigation on Purification and Degassing of TiB₂/Al Composite Fabricated by LSM Method</li><li>Polyimide-Epoxy Blend for Binding Silicon Steel Sheets of Aerospace Electrical Machineries</li><li>Investigations on Hydrogen Content Change in Melt Aluminum during Casting under Adjusted Pressure </li><li>Investigation on Friction and Thermal Expansion Coefficients of Al-Sn Bearing Alloys </li><li>Steel Water Continuous Casting Slag Detection System Based on Wavelet</li><li>The Cutting Energy of Rubber Cutting by a Sharp Cutter</li><li>Study on Structure of the New Polymer-Poly (Propylene-Co-?-Butyrolactone Carbonate) with Molecular Model</li><li>Experimental Analysis of Chemical Damage of Water to Soil Structure</li><li>Research on Mechanism of Stabilized Soil Mechanics Enhanced by Con-Aid Liquid Stabilizer</li><li>The Carbonyl Group Measurement of the Membrane Copolymerized by Low-Temperature Plasma at Atmospheric Pressure of C₂H₂ and CO₂</li><li>Influence of the Thickness and Frequency in the Infrared Hybrid Method in Consideration of Heat Conduction</li><li>Accuracy of Measurement of the Infinitesimal Deformation in Digital Image Correlation and the Intelligent Hybrid Method</li><li>Intensity of Singular Stress at the End of a Fiber under Pull-Out Force</li><li>Free-Edge Stress Singularity of Bonded Dissimilar Materials with an Interlayer</li><li>Structural Human Impact Analysis on Shooting: Experimental and Simulation </li><li>Computer-Aided Optimized Design for Multi-Alloyed Steels Specifying Hardenability Requirements</li><li>Flow-Induced Corrosion Simulation on a Plate by Finite Element Methods </li><li>"Glass Cullet" Generation Technique by Underwater Shockwave for Recycling System of Glass Bottles</li><li>Accurate Determination of Stress Intensity Factor for Interface Crack by Finite Element Method </li><li>Influence of the Various Li/Nb Ratios on Defect Structure and Photorefractive Properties of In: Eu: Fe: LiNbO₃ Crystals</li><li>Grain Refinement and Eutectic Solidification Mechanism of Al-Si Hypoeutectic Alloy in Centrifugal Casting with Electromagnetic Field </li><li>Microstructure and Ferroelectric Domains of SrBi₂Ta_1.6Nb_0.4O₉</li></ul>