Achievements of Mechanical Science and Current Technological Innovations for Sustainable Development

Preface, Committees
Chapter 1: Researching and Designing in Mechanical Engineering
Characteristics of Decompression Tank Internally Pressurized with Water Using OpenFOAM
Experimental Study on the Dynamic Characteristics of Hydro-Magneto-Electric-Regenerative Shock Absorber
Flexible and Ergonomically Three Wheel Bike for Post Stroke Patient
Thrust Force of Three Circular Windings of Conductor in Magnetic Field
Anti-Plane Interaction of a Coated Circular Inclusion with a Crack Located in Matrix
Influence of Spring Ratio on Variable Stiffness and Damping Suspension System Performance
Inverse Kinematics Modelling and Simulation for Upper Case Writing Robot Control Using ANFIS
Dimensionally Homogeneous Jacobian and Condition Number
Type Synthesis of Two DOF Hybrid Translational Parallel Manipulators
Effect of Impeller Condition on Blower Performance, Case Study: Impeller of K-2201 in Pt. Pertamina RU III
Base Aspect Ratio Effects on Resonant Fluid Sloshing in a Rectangular Tank
Morphology of Crown Tube Austenitic Stainless Steel TP316 HTF Failure
Metallography Investigation of Dry Corrosion Boiler Tube
Effect of Adhesive Layer Thickness on the Shear Strength of Adhesively Bonded Steel Joints in Wet Environment
Chapter 2: Heat and Mass Transfer, Fluid Engineering
Numerical Study of Mixed Convection around a Heated Circular Cylinder
Cooling Load Estimation to Determine the Proper Capacity of Air Conditioners in the Engineering Building at Engineering Academy of Soroako
Convective Regimes on Porous Media within Sudden Changed Channel due to Tangential Gas Flow
Effect of Mass Flow Rate on Dryer Room Radiator Pressure Drop and Heat Transfer
CFD Studies of the Dynamic Stall Characteristics on a Rotating Airfoil
Analysis of Turbulence Characteristics in the Laminar Sub-Layer Region of a Perturbed Turbulent Boundary Layer
CFD Analysis on Thermal Comfort and Indoor Air Quality Affected by Partitions in Air-Conditioned Building
CFD Based Investigations into Optimization of Diffuser Angle on Rear Bus Body
A CFD Analysis of the Viscous Fluid Behavior of Glycerin in Various of Stirring Patterns
Rheology Margarine on Non-Newtonian Fluid Proving through Small Gap
Chapter 3: Tecnologies Materials Processing
A Review Paper on Product Surface Defect Detection of Ironing Process
Tempering Process Gradually to Improve Quality Tool
Optimization of Cable Ties Injection Molding Process Using Back Propagation Neural Network and Genetic Algorithm (BPNN-GA)
Influence of Argon-Nitrogen Gas to Balance the Microstructure in the Welding of Super Duplex Stainless Steel
The Effects of Pulse on Time and Arc on Time on Surface Quality in Wire-EDM of ASSAB XW-42 and ASSAB 8407 2M Tool Steels
Multi Response Optimization Using Taguchi-Grey-Fuzzy Method in Drilling of Kevlar Fiber Reinforced Polymer (KFRP) Stacked
Optimization of Multiple Response Characteristics in the WEDM Process of Buderus 2379 ISO-B Tool Steel Using Taguchi-Grey-Fuzzy Logic Method
Groove Overhang Impact on the Result of Surface Roughness on Vertical CNC Milling Process
Simulation of Ironing Process for Bullet Case to Get Minimum Forming Force with Variation of Die Angle and Reduction Wall Thickness
Numerical Simulation of Cutting Stress Deformation in Tungsten Carbide Turning Tools
Friction Stir Welding on Corner Joint with New Surface Preparation Design
Effect of Hydrogen Addition on the Characteristics of Nitrided Martensitic Stainless Steel AISI 420
Effect of Low Temperature Sintering on the Porosity and Microstructure of Porous Zeolite Ceramic
Chapter 4: Coastal Engineering, Geotechnical and Civil Structures
Design and Modeling Pile Breakwater for LNG Jetty at Senoro Field, Central Sulawesi
Investigation of Risk Based Decision Making for Mobile Mooring System
Model of Ground Water Elevation around Mud Reservoir in Coastal Area of Porong Sidoarjo
Anchor Strength Analysis for Mooring of a Floating Breakwater in Senoro Field, Central Sulawesi
Response Reduction of Two DOF Shear Structure Using TMD and TLCD by Considering Absorber Space Limit and Fluid Motion
Chapter 5: Design and Research of Technologies and Equipment for Alternative Energy Sources
Optimization of Water Scrubbing Method for Enhancement of Biogas Quality through Base Solutions Addition
The Effect of Nitrogen on Flame Characteristics in Biogas External Premixed Combustion
Flame Stability Measurement on Rectangular Slot Meso-Scale Combustor
Experimental Study and Analysis of the Generated Electric Power of Salter Duck-Ocean Wave Energy Harvester (OWEH) due to Additional Weight Change and Wave Amplitude
Simplicity Design of Hybrid Energy of Marine Current and Offshore Wind Energy Plant in Indonesia
Simulation Savonius Wind Turbine with Multi-Deflector
Performance of Distilled Water Electrolysis with Adding of Sodium Bicarbonate as Catalytic
A Couple of Savonius Wind Mill and Centrifugal Reaction Pump as a Wind Energy Water Pump System
Experimental Study of the Cross Flow Turbine
Chapter 6: Industrial Engineering
Modeling of Well Service and Workover to Optimize Scheduling of Oil Well Maintenance
Evaluation of Delay Factors in Jacket Structure Project
Strategy in Reducing the Pace of the Greenhouse Gas Emission from the Electricity Sector in Southeast Sulawesi