Frontiers of Manufacturing Science and Measuring Technology IV

Preface and Committee
Chapter 1: Materials Engineering, Technology and Application
A Comparative Study of Neat Epoxy Coating and NanoZrO2/Epoxy Coating for Corrosion Protection on Carbon Steel
Analysis of Factors Influencing the Performance of Q460 Steel
Development and Application of Aluminium-Lithium Alloy
Friction and Rheological Properties of Meso-Porous MCM-41/Unsaturated Polyester In Situ Composites
Experimental Study of Low-Pressure Water Jet Assisted Laser Drilling on Al2O3 Ceramic
A New Method for Testing the Asphere Surface with a Liquid Crystal Spatial Light Modulator
Analysis the Tool Wear of Screw Drill during the Drilling of Steel X04Cr16Ni12MnTiN
Comparative Study of Different Cadmium Salts on Nano-Structured CdS Thin Films Prepared by CBD
Corrosion Resistance of X52 Pipeline Steel at Sea Mud Zone
Effect of Mn (II) Ion on Abrasive-Free Polishing of Hard Disk Substrate
Experimental Study on Process Parameters of High-Speed Micro-Milling Al2O3 Ceramics
Experimental Study on the Burning Behavior of Automotive Internal Decorating Materials
Influence of pH Values on the Morphology and Down-Conversion Luminescence Properties of Zinc Tungstate Micro Nano Crystal Synthesized by a Hydrothermal Method
Mechanical Properties Analysis and Application of Metal Matrix Composites
Medical Building Materials of Structural Properties and Electromagnetic Interference Shielding in the Quartz Crystal Plane Coated Ni Based Thin Film
Morphology-Controlled Synthesis of ZSM-5/MCM-41 Composite Zeolite
Near Net Shape Forming Process of a Titanium Alloy Component Using Hot Isostatic Pressing with Graphite Mould
Nitrogen Doping Effects on Microstructure of Multi-Walled Carbon Nanotubes
Research on Feasibility and Applicability of Delamination Localization Methods for Composite Laminated Beams
Side Effects on Enhancing Chemical Herbicides to Control Proposal
Simulation Research on Optical Performance of Multicrystalline Silicon Texture Structure
Strengthen of Mechanism of 30CrMnSiNi2A Steel Welded Joint with Ultrasonic Impact Treatment
Study on Ball Milling of TiH2 and Application in Energetic Materials
Study on Corrosion Damage Rule for Two Type of Aluminum Alloy
Study on Features and Application of Typical Smart Materials
Study on Nanometer ATO Powder Prepared with Citric Acid as Dispersant and its Conductive Properties
Surface Modification on Rabbit Hair Fiber for Anti-Static and Ultraviolet Protective Properties via ZnO Nanopartciles
Synergistic Effects of a Red Phosphorus Master Batch on a Modified Intumescent Flame Retardant ABS Composites
Synergistic Flame Retardant Effect of Fumed Silica and Zinc Borate with Magnesium Hydroxide in ABS Based Flame Retardant Composites
Texture Evolution of Friction-Stir-Welded 5A30 Aluminum Alloy Plate
The Aging Properties of Bamboo-Poplar Composite Oriented Strand Board with Different Hybrid Ratios
The Development of Double Composite Flexible Radar Absorbing Fabrics Based on Iron Fibers
The Discussion about Concrete on the Relationship between Corrosion Resistance and Time under Bending Loads
The Friction and Wear Properties of Cu-Te-Li Alloys with High-Strength and High-Conductivity
The Range Distribution of Yb Ions Implanted in 6H Silicon Carbide
Ultrasonic Inspection for Metal Creep Based on Flight-Time-Attenuation
Corrosion Behavior of Titanium Alloy and Titanium in Different Solution
The Analysis of Temperature Field of Concrete Beam of Hydration Heat
Effect of Fumed Silica and Zinc Borate on the Thermogravimetric Analysis Curves of ABS/Magnesium Hydroxide Composite
Analysis the Machined Surface Quality during the Drilling of Steel X04Cr16Ni12MnTiN
Double Sided Explosive Cladding of Stainless Steel and Regular Steel
The Influence of Particle Diameter on Analytical Results
Experiment Research of Laser Induced Air Breakdown
Chapter 2: Applied Mechanics, Design, Simulation and Manufacturing
A Study of Simulation of Hydropreumatic Suspension Experiment Rig Based on AMESim and Matlab/Simulink
90W Off-Line High Power Factor Correction Module Design
Applications of the Photothermal Cohesion Technology in the Fresh Air System and Air Purification Devices
Based on Rub a Drum Machine Four-Axis Machining Fixture Design and Modeling in Solidworks and Virtual Assembly
Based on Solidworks and Mastercam Combined for Rub a Drum of Four-Axis NC Machining Programming Research
Cavitation Effect to the Hydraulic Piston Pump Flow Pulsation
Comparison of the Load with Different Loading Ways in the Finite Element Model of the Mobile Air Compressor Frame
Deformation Analysis of Dam with the Improved Wavelet Threshold
Design and Analysis of a Novel Micro Flying Head in Mass Storage System
Design and Optimize the Branch Pattern of Herringbone Well
Design and Simulation for Braking System of FSAE Racing Car
Design and Simulation of a Descent Control Device Based on Hydraulic Damping
Design of a Type of Lift Coating Machine
Design of Injection Mould for the Special-Shaped Claw Cover of an Automatic Breast Pump and Milking Machine
Design of Testbed for Feel Simulator of Battleplan
Development of Hole-Based Self-Centering Marking Gauge
Development of the Assistant Positioning Device of Parallel Machine Vice
Disk Cam Contour Design Based on Inventor 2009
Dynamic Modeling of Shaking Table Based on Simulink/SimMechanics
Dynamics Analysis of a 3-DOF Parallel Mechanism
Effect of the Rudder on the Vibration Frequency of Wind Turbine
Electromagnetic Simulation and Dynamic Analysis about the Electromagnetic Propelling System of Magnetic Suspension Launcher
Fault Diagnosis Approach for Incipient Bearing Fault in Wind Turbine under Variable Conditions
Finite Element Analysis and Experimental Research for Horizontal Tank to Internal Magnetic Flux Leakage Detection
Hardware Design of Automotive Parking Heater Remoter and Receiver
Heavy Duty Automobile Self-Discharging Hydraulic System Design
Horizontal Well Fracturing Optimization Numerical Simulation
Hydraulic Excavator Boom Lightweight Design
Intensive CNC Machine Programming with Circular Pattern Algorithm
Machine Gun Finite Element Model Amending Based on Frequency Response Functions of Vibration
Modeling and Simulation of Turbofan Engine Based on Modularized Subassembly
Modular Design Technology of Multi-DOF Mechanical Arm
Multi-Objective Collaborative Optimization of Spring
Numerical Investigation of Tip Clearance Flow in an Axial Compressor Cascade
Numerical Simulation of the Shell Fragments Damage-Field Based on ANSYS/LS-DYNA
Numerical Simulation Research of Air-Assisted Atomizer Internal Gas Flow Field Based on Fluent
Parametric Design of Tapered End Mills with Variable Pitch for Improving Stability
Permeability Improvement Technology of Directional Hydraulic Fracturing in Low Permeability
Pre-Deformed Design of Optical Lenses with Reverse Engineering and Virtual Manufacturing
Research and Development of a Knowledge-Based System for Blanking Die
Research on Attitude Singularity Problem of Small Tail-Sitter Aircraft
Research on CNC Machining System of Directly Driven by Image Based on PMAC
Research on Influence Factors of Landing Gear Retractile Hydraulic System Performance Degradation
Research on the Forming Path for Fabricating the Sheet-Metal Part with Non-Horizontal End Face Using CNC Incremental Forming
Research on the Simulation of NC Milling Program Based on VERICUT Oriented to the Five-Axis Micro-Milling System
Research on the Stress Uniformity of the High Speed Bearing with Heavy Load in Cold Rolling
Research on Typical Vibration Accelerations of Wind Wheel Changing with Yaw Angle
Rolling Bearing Feature Extraction Based on Wavelet Filtering with Optimal Combination Bands
Second-Order Two-Scale Asymptotic Expansions for Thermopiezoelectric Problems in Periodic Structure
Simulation and Design of Portable Underwater Acoustic Transducer Test Device
Simulation and Optimization Design of Gasoline Engine Exhaust Muffler
Simulation and Optimization for the Cooling System of Heavy Vehicle Engine
Simulation and Parameter Design of a 10kw Wireless Power Transfer System Applied to Gantry Crane
Simulation and Test Study of Multidisc Magneto-Rheological Fluid Clutch
Simulation Study on a Parallel Hybrid System of Hydraulic Excavator
Structural Optimization of Drilling Bed for Deep Hole Drilling Machine
Study on Influence of End Concavity of Rolled Piece by Billet Circular Arc Angle with CWR
Study on Split-Open Loading in V-Shaped Components Forming Process
Study on the Welding of Feeder Hopper and Cylinder Instead of Casting Process
The Design of the Fixture for the Thin Wall Cone Parts
The Design of Wave Height Standard Device in the WTTVS and its Error Analysis
The Design Research on the Key Components of Low-Speed Marine Diesel Engine
The Forced Response Analysis of Heavy Duty Vehicle's Cab
The Nanocutting by Rigid/Elastic Tools with Nose Radius at the Gas Environment Using Molecular Dynamics Simulations
The Optimal Design for Ring Blank Dimensions in Inner L-Shaped Ring Rolling Process
The Parametric Design and Simulation for Globoidal Indexing Cam Mechanism
The Research of New Rings Process of Casting-Rolling Continuously Forming
Thermal Deformation Analysis of a Magnetic Climbing Wall Car Frame Based on the ANSYS
UML Based Design Approach for Storage System of Nano-Satellite
Biomechanical Analysis of Typical Upper Limb Movements Based on Kinect-LifeMOD
Dynamics Simulation Research of Planar Four-Bar Mechanism with Multi-Joint Clearance
Data Flow Analysis on 3D Printing for Distributed Manufacturing Information System
Modal Analysis Based on Finite Element Jaw Crusher Rotor
The Dynamic Strength Calculation on the Reel Fulcrum of Crane Based on ADAMS and FEA
Surface Waviness in Abrasive Waterjet Offset-Mode Turning
Develop the System of Three Dimensional Parametric Design of Planetary Gear Reducer Parts Library Base on CS Structure
Optimization Design of Hot Runner Injection Molding for Thin Shell Parts Based on Moldflow
Parameter Identification of a Plastic Damage Model
Research on the Molding Condition of 3D Braided Nozzle Throat Fabric
Stress Analysis for Globoidal Indexing Cam Mechanism with Steel Ball
Stress Forming of Fine Metal Wire Based on Ultrasonic Vibration
Study on Bladder Forming of the Shallow Basin-Shaped Aluminum Sheet Parts
Multi-Type of Generators Scheduling Optimization Model Based on LHS Method and the Mean-CVaR Model
Research on the Common Rail Transport System Building in Integration System of Urban Rail Transit in Hohhot
Numerical Investigation of Choking Cavitator Based on Orthogonal Experiment
Research on One Kind of Intellectualization High Accuracy Digital Adjustment Direct Source
An Inquiry into the Sustainable Development of Cellulosic Ethanol in Tianjin, China
Main Technologies of Life Support System of Evacuated Tube Transportation Vehicle Passenger Cabin
Modeling and Predicting Surface Roughness for the Grinding Process
A Band-Gap Voltage Reference for LDO Circuit
A Photovoltaic Soft Switching Boost Circuit
Calculate Formation Velocity from Vertical Seismic Profiling Data
Design of a 10MPa Nanosecond Gas Switch with Adjustable Gap
HMI Design of Lead-Acid Battery Retreading System Based on DWIN DGUS Screen
Key Technologies of Rigid-Flexible Coupling System Modeling and Simulation
Research Method and Key Design Themes of a Multifunctional Jacket with Optoelectronic Effects
Design, Fabrication and Evaluation of a Multifunctional Jacket with Optoelectronic Effects
Chapter 3: Measurement, Monitoring, Control and Testing Technologies
A Certain Type of Artillery Open Loop Servo System Reform Research Allocation Zoom Multiples
A Control System on Soil Temperature
A Method of Coordinate Measuring Path Planning Based on Polychromatic Sets
A Novel Optical Fiber Displacement Measurement System
100MHz to 2.5GHz RF Detector Based on SiGe HBT
A Kind of Online Insulation and Error Online Monitoring Technique
A Method of Correcting Brightness Gradient in Thermal Infrared Image
A Method of Full Digital Clock Generation with Adjustable Frequency and Phase
The Factors Influencing the Surface Quality of Machining and Improving Measures
The Intelligent Traffic Monitoring System Based on Beidou Research and Design
The Model Establishment and Simulation Analysis of Controllable Pendulum
The Number of Runs and its Application in Biological Medicine Testing
The Optimized Design of Coordinated Control System Based on Load Feedforward and Unidirectional Decoupling
The Research of Network Intrusion Detection Technology Based on Genetic Algorithm and BP Neural Network
The Research of Radio Monitoring System for Army Digital Force Training
The Research of Self-Balancing Vehicle Based on Posture Sensor System
The Resulting Toolpath of Turning a Special Surface on CNC Lathe
The Simulation about Single-Phase Bridge Type all Control the Rectifier Circuit is Based on Matlab
The Study on Voltage Control Based on MAS and Grid Technology
Theoretical Study on Bridge Structure Condition Evaluation Based on Health Monitoring Data
Transient Stability of Power System Based on Multi-Agent System
Vehicle Trajectory Prediction Based on Road Recognition
Waveform Measurement and Analysis of Common Household Appliances
A Novel of L-Serine/Chitosan Electrochemical Sensor for Determination of Paracetamol
A Practical Signal Progressing Method for Magnetic Flux Leakage Testing
A Single-Cell Replacement Strategy on Electronic Array Self-Healing
A Survey on Moving Target Tracking in the Intelligent Visual Monitoring System
Adaptive Fuzzy PID Control Applied in Boiler System of Power Plant
An Approach for Detecting Illegal Load in Wireless Power Transfer System
An Image Positioning Method of Automatic Random Walker Based on IFS Edge Detection
An Improved Adaboost Method for Face Detection
An Improved Algorithm for Real-Time Moving Target Detection Based on Gaussian Mixture Model
Analysis and Research of Rogowski Coil Current Sensing Technology
Analysis of Air Power Switch Work under Harmonic
Application of BP Neural Network PID Algorithm in Refrigerated Space Temperature Control
Application of Parameter-Adaptative Fuzzy PID Control in the Temperature Control System for Liquor Filling and Sealing Machine
Approach to Design Digital Meter for Monitoring Armored Vehicle Engine
Auto Disturbance Rejection Control Strategy for Large Inertia Servo System
Automatic Test and Fault Diagnosing System of XX Airborne Navigation and Control System
Based on Energy-Efficient Opportunistic Multicast Routing for Mobile Wireless Sensor Networks
Critical Event-Triggered Transmission for Wireless Sensor Node in Aircraft Structural Health Monitoring
Design and Analysis of Dual Hall Position Sensor with Automatic Direction Recognizing and Pre-Positioning Function
Design and Analysis on the Anti-Lock Braking Control System of a Four-Wheel Vehicle
Design for Speed Measuring of Railway Crossing Based on Track Circuit
Design of a Fast Resistance Sorting Instrument Based on STC Microcontroller
Design of a Temporary Ground Wire Monitoring System and Reliability Research
Design of a Two Levels Self-Integrating Capacitive Divider
Design of Automatic Milking Controller
Design of Digital Type Axis-Angle Sensor Based on Singlechip
Design of Plunger Limit Switch Testing System Based on Virtual Instrument Technology
Design of the IDCTMV Human-Machine Ergonomics Test System
Design of the Target Tracking Process Based on DM648
Development of Experimental Apparatus for Diaphragm Gas Meter in the Limiting Temperature Conditions
Development of the Portable Field First-Aid Diagnosis Bed
Diesel Engine Inlet and Exhaust System Fault Detection Based on PSO-BP NN
Effects of Quay Wall and Seabed Reflection on the AUV Acoustic Radiation Test Analysis
Empirical Likelihood Based Testing for Polynomial Regression Models
Experimental Study on the Emergency Ampacity of XLPE Cable and its Application
Experiments and Analyses of Horizontal Earth Electrodes' TGR on Various Grounds
Finite Element Analysis of Capacitance Sensor
FPGA-Based High Precision Illumination Measurement System: A Prototype Development and Evaluation
Frequency Control QPSK Modulator Based on DDS Technology
Fuzzy Neural Network Based on Genetic Algorithm for Temperature Control of Variable Air Volume Air Conditioning
Hybrid Base and Parallel Hybrid Electric Vehicle Control Strategy
Improvement of Stable Operation Ability for Large-Scale Wind Power System Based on VSC-HVDC Technology
Initial Orbit Determination Using Single Frequency GPS Measurements of Launch Vehicle

In Situ Tester Research and Development of Control Stick Force Sensor
Laser-Welding Spots Detection Based on Original Moment Values
Many High Performance Motion Control of Linear Motor Drive System Research
Modal Hammering Test and Sensitivity Analysis for BIW Vehicle
Modeling Analysis and Experimental Study of Circular Piezoelectric Unimorph Actuator
New Method of Angle Error Measurement in Angular Artifacts Using Minimum Zone Flatness Plane
Nondestructive Testing Methods of Coating Performance
Offset Error Research of Self-Triggering Pulsed Mini Laser Radar System
Ontology and Multi-Agent Based Intelligent Retrieval Model for Power Quality Monitoring Information
Optimization of Reliability Test on the Shell of Portable Electronic Products Based on Taguchi Method
Research and Application on Intrusion Detection Technology Based on Improved BM Algorithm
Research and Design of Touch-Screen Domestic Universal Remote Controller with Self-Learning Function
Research on Active Online Diagnosis Technology of Hydraulic System
Research on Data Acquisition Technology of Wind Turbine Monitoring System
Research on Key Techniques of Multi-Sensor Intelligent Video Surveillance System
Research on Test Technology of Remote Weapon Station's Dynamic Parameter
Research on the Pattern of Boom-Type Roadheader Intelligent Control System
Research on the Simulation Design System of Indoor Precise Control Field Based on VRML
Research on the Technology of Middleware of Distributed Spectrum Monitoring System
Simulation of Magnetically Controlled Reactors Based on MATLAB
Splitting Strength Detection Test of Shallow Asphalt Pavement and Master Curve of Splitting Strength
Study on Intelligent Anti-Theft Alarm System of Power Transformer
Synchronization Control Scheme for Antenna Pointing Control System Based on Hybrid Linear Actuator
Test and Analysis of Dynamic Characteristics of Reinforced Concrete Arch Bridge
Testing Research of Fiber Bragg Grating Strain Sensor Embedded in Bored Pile
The Application of PSO-BP Neural Network PID Controller in Variable Frequency Speed Regulation System
The Construction Quality Control Measures of Reinforced Concrete Cover Research
The Design and Simulation of Scheelite Alkali Autoclave Reactor Fuzzy-PID Controller
The Design of Automatic Remote Monitoring System for the Temperature and Humidity Based on GPRS
The Design of Communication System for Wearable Health Monitoring Equipment
The Design of Greenhouse Temperature Control System
The Design of Landslide Hazard Remote Monitoring System Based on STM32 MCU and GPRS
The Development of an Automatic Ultrasonic Non-Destructive Testing System
Design of Temperature Control System Based on FPGA and Fuzzy-PID Control Algorithm
Development of Two-Dimensional Motion Platform Control System Based on xPC Target
Research on PVDF Micro-Force Sensor
Sound Recognition Algorithm for Power Devices Based on Substation Inspection Robots
Static Characteristic Test of High Temperature Pressure Sensor
The Characteristics of Dyed Fancy Yarn Formation Pattern Research
The Measurement of Concrete Temperature Distribution Based on VB
An Intelligent Traffic Signal Controller Based on CAN Bus
Introduction to Computers in the Mechanical and Electrical Control is Widely Used in the Field of Industry
Long-Endurance Multi-Function Floating Platform
A Fast Pose Estimation Method of Four-Rotor Aircraft
Research of Small Current Grounding Fault Classification Based on Phase Plane Method
A Kind of Portable Wire Rope Testing Equipment
Blind Pipe Type Fiber Bragg Grating Hydrostatic Gauge
Research on the Detection of Focusing Mechanisms
Design of Programmed Temperature Control Gas-Sensing Characteristic Tester
Development of Automatic CNC Grooving and Bending Machine Based on MPC08SP Motion Control Card
Research on XCTD Launcher Based on EML Technology
Scanning Mirror Topology Optimization of the Imaging Spectrometer
Development of the Comprehensive Performance Test Equipment of the Electromagnetic Switch on Automobile Starter
Dynamic Matrix Control for Multiple Gas Collectors of Coke Ovens
Effect of Vehicle Speed on Contact Pressure and Current Collecting Quality
Gear Fault Signal Modeling Study Based on Probability Box Theory
5T Information Fusion System Based on Train Technology Scheme Design
Prediction of PAHs Emitted from Marine Diesel Engine Using Artificial Neural Networks Combining Genetic Algorithms
Research on Flood Control Operation for Poyang Lake Semi-Restoration Dikes are Based on Variable Fuzzy Optimization Theory
Research on Reliability Allocation Method for NC Grinding Machine
Selection of Plate Self-Locking Nut
Study on Automobile Intelligent Automatic Clutch System
Study on Simulation of Aircraft Background Magnetic Field
Computer Modal Analysis of the Two-Dimensional Precision Turntable
The Electrical Standard Practices in the Role of Airbus Aircraft Maintenance
Application of Inverse Distance Weighted Interpolation Method in Finite Temperature Point Temperature Field
The Localization Method of ALV Based on Lateral Dynamics
The Path Recognition Method of Smart Car Based on Linear CCD
Soft-Starting Method Analysis of Belt Conveyor
The Tool Setting Skills of Round Parts in NC Milling
Research of Tracking and Prediction of Moving Object with Kalman
A Four-Coordinate CNC Device Based on Engraving and Milling Machine
Chapter 4: Communication and Navigation, Information Technologies, Algorithms and Numerical Methods, Image, Video, Signal and Data Processing
Design and Research of Biological Information Based on the Signal Extraction Algorithm
A GIS and Web-Based Decision Support System for Regional Water Resource Management and Planning
A New Numerical Scheme for the Space Fractional Diffusion Equation
A Class of Difference Inequality with Three Iterative Summation
A Degree Distribution Optimization Algorithm in Unequal-Protected LT Code
A Fast PSF Calibration Method for Single Lens Imaging
A Method for Analyzing Clinical Heart Sound Signal Based on Chaotic Characteristics
A Method for Software-Related Safety-Critical Scenarios Identification
A New Auto-Extraction Algorithm of Lunar Craters for Chang'E Data Based on the Solar Incidence Angle
A New Auto-Extraction Algorithm of Multi-Size Lunar Craters Based on the Chang'E Data
A New Method for Code Optimization
A New Rough Set Model and its Application
A Novel Blind Source Separation Algorithm for Linear Mixture Signals
A Novel Distribution Parameter Fitting Algorithm of Correlation Noise Model for Distributed Video Coding
A Novel Method of Spike Detection for Interferograms Based on Two-Step Filtering
A Novel Overlapping Community Detection Algorithm of Weighted Networks
An Assessment Method of the Data Similarity Considering the Shape Differences of Objects
An Improved Decision Strategy of Network Routing Based on Ant Colony Algorithm
An Improved Error Concealment Technique Based on Multi-View Video Coding
An Improved Frame Loss Concealment Algorithm Based on the Mixed Excitation Linear Prediction
Analysis and Simulations of Lensless Imaging with Intensity Correlation Method
Analysis of Black Level Calibration Algorithm for CIS
Application Demand Analysis of Message-Oriented Middleware with Pub/Sub Model on TT&C Computer
Application of C Sharp and MATLAB Mixed Programming Based on .Net Assembly in Blind Source Separation
Bayesian Compressive Sensing of Images Based on Effective Blocking
Campus Tracking System Based on IoT
Candidate Region Detection of Ship Target in Port Based on Electronic Map
Car Branding and Communication Strategy Research Based on Microblogging
Characteristic Study on Carrier Communication Device Noise of Low Voltage Power Lines Based on UPS
Certificateless Multi-Signcryption Scheme without Pairing
Chinese Short Text Semanteme Analysis and Emotion Value Quantization Algorithm
Collaborative Filtering Recommendation Technology Based on Genetic Algorithm
Compressed Sensing Image Reconstruction Based on Improved Particle Swarm Optimization Algorithm
Computer Network Security Strategy Research
Construction of Data Association Model in Coal Mines Based on the Application of Internet of Things
Design and Implementation of FPGA-Based High-Performance Floating Point Arithmetic Unit
Design of Ultrasonic Rangefinder Controlled by Single Chip Microcomputer
Detection and Parameter Estimation for Chirp Signal Based on Fractional Fourier Transform
Detection and Tracking for Anomalous Motion Targets Using Wireless Sensor Networks
Distance Features of Different Fatigue State
Early Warning of Power Plant Equipment Based on Massive Real-Time Data Mining Technology
Efficiency Analysis of Different Cooperative Communication Schemes in Wireless Sensor Networks
Enumeration of the Generalized Rook Monoid
ERP Feature of Matching Pennies
Estimation of Distribution Algorithm using Two Kinds of Information for Solving Knapsack Problem
Face Recognition Image Processing Design Research
Fault Prediction Methods Study of Machinery Based on Optimized Background Value MGM(1,m) Model
Feature Extraction of Underwater Target Ultrasonic Echo Based on Wavelet Transform
Fusion of Visible and Infrared Images Based on Non-Sampling Contourlet and Wavelet Transform
GaAs MMIC Wideband SP8T Switch
Hardware Design of Track Circuit in Rail Transit Test System Based on ICL8038
HD Video Online Recognition Based on DCT Spread Spectrum Watermarking Algorithm
Holography Reconstruction of the AUV Radiated Acoustic Field and the Influencing Factors Analysis
Image Processing and Sparse Resolution for Underwater Imaging
Implementation of CRC in 10-Gigabit Ethernet Based on FPGA
Improvement of K-Anonymity Location Privacy Protection Algorithm Based on Hierarchy Clustering
Mobile Learning Mode Based on 3G
Modeling and Analyzing of RRC Protocol Process Based on CPN
Motion Comparison Method Combining Segmented Multi-Joint Line Graphs with the SIFT Matching Technique
Multi-Channel MKL for Video Human Action Recognition
Network Equipment Selection Scheme of University Informatization Construction
New Data Processing Method Research on GLONASS
Optimal Path Planning of Beidou Navigation System Based on Dijkstra Algorithm
Parameter Estimation of Nonlinear Muskingum Models Based on OEPSO
Prediction of Road Congestion Level Based on Bayes Algorithm
Real Time Message Matching Algorithm for Message-Oriented Middleware with Pub/Sub Model on TT&C Computer
Receive and Display Beidou Positioning Information Based on MapX
Recurrence Characteristics Analysis of Near-Surface Wind Speed Signal with Different Sampling Frequencies
Research and Simulation of LCMV Algorithm in GNSS Anti-Interference
Research of an IPSec VPN Application in Enterprise Network
Research of LXI Discovery Method
Research of Text Recognition Based on Natural Scene
Research of Weapon Training Simulator Software Model Based on UML
Research on Combined Weight of Target Threat Index of Information Fusion
Research on Flight Altitude Information Fusion Method for ADS/INS/GPS Integrated Systems Based on Federated Filter
Research on Information Exchange Platform Based-Web Services for Tourist
Research on Information Interactive Model of Automated Demand Response
Research on Limit-Trajectory Over-Modulation Strategy of Two Stage Matrix Converter
Research on SIFT Matching Algorithm Based on GPU
Research on Switch Power Module Parallel Operation System
Research on the Application of Cloud Computing in the Field of Archives Informatization
Research on the Performance Test of Wired/Wireless Heterogeneous Industrial Control Network
Research on Vague Set of Target Threat Information Fusion Algorithm
Research on Wireless Network Traffic Modeling Based on Channel State
Research on XML Documents and Relational Database Mapping Based on XML Schema
Simulation of Clouds Dynamics Based on the Change of Sight Distance
Small Quantities of Cargo Transportation Route Selection Base on Minimum Spanning Tree Algorithm
Smart Meter Based on Smart Energy Profile for ZigBee and Power Line Communication Connectivity-Enabled Home Area Network
Software Design for Micromouse Special Navigation
Software Design for Micromouse Straight Path Navigation
Solid Rocket Motor Finite Element Analysis Based on the Reverse Modeling of ICT Images
Solitary Wave Solutions, Periodic Wave Solutions and Folded Localized Excitations for the Dissipative Zabolotskaya-Khokhlov System
Speaker Recognition Techniques
Study of Archives Information Development Based on SWOT Analysis
Study of Steady-State Kalman Filtering Based on Thresholding Optimal Gain
Study of the Simultaneous Generation of UWB Doublet and Triplet Signals Based on Nonlinear Effects of SOA
Study on Synthetic Aperture Radar Image Denoising Algorithm
Study on the Method of Vibration Signal De-Noising Using Wavelet Packet Based on QPSO
Summary and Expectation of Synthetic Aperture Imaging towards High-Orbit Objects
Text Clustering Algorithm of Co-Occurrence Word Based on Association-Rule Mining
The Analysis of Steganographic by Sub-Pixel Calibration
The Combination Views of Privacy-Protection in the Mobile Database
The Design and Realize on the Circuit Board of High-Speed Image Acquisition System
The Differences Analysis of Input-Output Efficiency of Regional R&D Activities Based on DEA
The Exploration and Implementation of the Interactive Multimedia Network Autonomous Learning Platform
The Optimization and Application of Kriging Model Based on Quantum-Behaved Particle Swarm Optimization
The Solution to Node Importance in Complex Networks Based on PageRank Algorithm
The Study of a Fingerprint Encryption Code Model
The Study of Harmonic Suppression and Reactive Power Compensation
The SWOT Analysis of the Application of Cloud Computing to Archives Informatization
Topological Structure - Based Rough Sets and Rough Logic
Ultra-Low Frequency Difference Signal Multiplication Based on PLL
Uncertainty Evaluation of Duration of Aircraft DC Transient Signal Based on Least Square Method
University Employment Information Integration Model Based on Cloud Computing
Wavelet-Based Adaptive Detection of Magnetic Anomaly Signal Contaminated by 1/f Noise
Weakness and Improvement of an Efficient Key Agreement Protocol
Wideband SPDT Switch With TTL Control
Comparison and Improvements of Feature Extraction Methods for Text Categorization
A Discriminative Method for Pedestrians Detection on Real-Time Video
Research on the Iterative Stopping Criterion Based on Linear Turbo Equalization
Big Data Reasearch on Smart Phone Unlock Crack
Corneal Image Analysis and Information Management System Based on Slit Lamp
Design and Implement of a Computer Forensics Model for Cloud Environments
Design of Wave/Tide Simulate Apparatus' Control Software Based on Free Port Communication Protocol
Image Decomposition and Inpainting Based on Besov and Hilbert-Sobolev Space
iMRAproiri: A Parallel Aproiri Algorithm Based on Twister
Research on Industrial Control Network Webstation Design
Research on Bandwidth Allocation of Multimedia Communication System Based on Internet of Things
Research on Design of Network Curriculum
Information Communication Technology Applications for World Heritage Site Management
The Diagnosis Research of Cover Sheet Spring Recover on the Compensate Fuzzy Nerve Net of Multi-Input Defer
The Performance Evaluation of the External Effect of Regional Logistics Information Platform
Novel Algorithm for Calibrating Speed-Density Model Parameters in Mesoscopic Traffic Simulator
Design and Realization of Collaborative Simulation on VRNET and VR-Forces Cross Platform
Optimization of Maintenance Equipment Tool Types Based on Triangle Fuzzy Number
System Mechanism of Small IOT System - Taking the Openhab Project as an Example
The Application of Tolerance Database in the Secondary Development of SolidWorks
A Novel Cluster Selection Algorithm in the NIDS of Wireless Ad Hoc
A Novel Nonlinear Time Series Prediction Method and its Application in Structural Vibration Response Prediction
A Solution of Designing Remote Video Conferences Based on ARM11
Analysis and Simulation to the Anti-Jamming Performance of the CCSK Soft Spread Spectrum System
Consensus Analysis for a Class of Heterogeneous Multi-Agent Systems in Directed Graph
The Application of Multimedia Video Technology in 3D Table Tennis Games
Optimal Power Flow Solution Using the Harmony Search Algorithm
Power Harmonic Analysis System Based on Virtual Instrument
Reconfigurable Virtual Instrument Test System Research Based on Mobile Platform
Replacement of the Power Generation Unit and Benefit Allocation Model Based on the Power Generation Performance
Research and Improvement about LEACH Algorithm for Wireless Sensor Networks
Research on Diffuse Optical Tomography System in Frequency Domain
Research on Remote Sensing Image Geometric Correction Method and Precision Analysis
Short-Term Wind Speed Prediction on Base of Improved Least Squares Support Vector Machine
Study of Convective Heat Transfer Coefficient of High Pressure Water Descaling
Study on Flood-Fill Algorithm Used in Micromouse Solving Maze
Study on the Wrapping Error of GREEN's Function Sampled in K Space
Status and Prospect of Disassembly Process of Electronic Components on Waste PCBs
Getting the Health Management Information System Building
Analysis for Position Selection of Hinged Point in a Forestry Transportation Articulated Vehicle
Chapter 5: New Technologies in Education and Sports
Research of the Experimental Teaching about IPSec Protocol Based on Transport Pattern
Research on Practice Teaching of Civil Engineering on the Basis of the Student Competition
Cross-Cultural Awareness in College English Teaching
Research on "Two Labs and Two Centers" Art and Design Practice Teaching Mode
Study on Students' Network Moral Education
The Application of Information Technology in the Fine Arts Teaching and Implementation
The Economic Analysis on the Special Education Teachers in Human Capital
The Innovation of the Construction of Style of Study of Connotative Development of Higher Education
The Research on the Core System of Athletics
Discussion on Research Learning under the Network Environment
Research and Practice of Teaching Reform of Wireless Network Technology Course for Internet of Things Specialty
Research on the Reform of Metallurgical Engineering Practice Teaching
Study on the Cultural Construction of College Archives
On the Design and Development of Micro-Course
The Design and Realization of Online Submitted System of Graduation Design Documents
Chapter 6: Management Engineering, Business and Economics Engineering
An Investigation of Electronic Logistics Management in the Taiwanese Textile Industry: Using Everest Textile as an Example
Analyses the Mechanical Equipment Management and Maintenance
Application of Lean Quality Management in Heat Treatment Industry - An Example of Enterprise N
A Modified Exponential Smoothing Model for Forecasting Per Capita GDP in Yunnan Minority Area
A Study on CPFR Inventory Management Technology
A Traffic Capacity Model of Lane Occupation
An Empirical Study on Exponential Smoothing and Seasonal Model
Based on Geographic Information System of Tourism Resources and Circuit Management System Design and Implementation
Design and Implementation of Room Management System of Hotel Based on J2EE
Design and Implementation of Storage Management System Based on Java
Design and Implementation of University Administrative Management System
Design of Prognostics and Health Management System for Turbofan Engine
Fuzzy Comprehensive Evaluation on Human Resource Management Risk Warning Model
Material Selection and Management Based on Cybernetics
Research on Episode Segmentation for MIS Workflow
Research on Purchase Intention Models of Seamless Underwear Consumers
Risk Assessment and Countermeasures of Occupational Fraud Conduct in Corporate Construction Projects
Team Organization Model and its Algorithm for a Project under Complex Constraints
The Comparative Study on Urban Transport and Urban Agglomeration Transport
The Theory of Economic Law to the Construction of Harmonious Society in our Country Value Analysis
The Urban and Rural Public Transit Demand Analysis in Hohhot
University Personnel Management System Construction and Implementation
Design Research on Computer Logistics Information Management System
Economic Analysis on Space Truss Structure under Different Specific Conditions
Research of the Store Image Based on Wechat Public Platform
Stakeholder Analysis of EV Spread in China
The Background and the International and Domestic Impact of 'General Data Protection Regulation'
The Design and Application of All-Areas and Best Traversal Algorithm Based on Uniform Points on Scene Check
The Legislative Reference on Software Vulnerability of Foreign Critical Infrastructure
Bound of Local Risk Minimization Estimation on g?Space
Computer Database System in the Application of Information Management
The Library Information Management System Analysis and Design
Modeling the Influence of Design Modification on Product Development Projects Based on Structure Methods
Theoretical Framework for Innovation Design with Optimised Customization
Research of State Assessment for UAV Based on FAHP
The Design of Operation and Maintenance Management System about IT Platform Based on Tivoli
Simulation Modeling of Post-Earthquake Vaccine Cold-Chain Emergency Transportation Based on ExtendSim