Progress in Materials and Processes

Preface and Conference Organization
Chapter 1: Composites
Fabrication and Characterization of Chromium-Coated Graphite Fibers Reinforced Copper Matrix Composites
Effective Means of Microstructure Homogenization for AgMeO: Cumulative Extrusion Severe Plastic Deformation
Oxidation Resistance of Graphite-SiAlON Bonded SiC Composite
Influence of Thermite Reaction on the Microstructures and Properties of Cast-Infiltration Composite Layer
Effects of High Temperature on Tensile and Bending Strengths of T300 Carbon Fiber Three Dimensional Braided Composites
Structure-Property Correlation of Composites Impregnated with Aspartimide Oligomer
Study on the Resin Curing Time and the Mechanical Properties of the Composites
Ag Supported Si-Doped Graphene for Hydrogen Sulphide Detection: A First-Principles Investigation
Influence of Interfacial Bond Strength on the Mechanical Properties of Resin Mineral Composite Reinforced by Molybdenum Fibers
Test Study and Application of Corundum Slag in Slag-Forming of BOF
The Effects of Fiber Volume Fraction on the Vibration Damping Characteristics of Three-Layer-Connected Biaxial Weft Knitted Fabric Reinforced Composite Materials
Characterization of the Interphase in Carbon Fiber/Epoxy Composites Using Force Modulation Atomic Force Microscope
Preparation of Cu2O (Cu)/MWCNTs Composite Particles and Their Gas Sensor Properties
The Modification of Mesoporous Silica SBA-15-Type with PEG
Preparation of Cu-Coated Diamond Particles and its Influence on the Performances of Diamond/Cu Composites
Synthesis and Characterization of Mn-Doped Copper Chromite Black Pigments
Investigation on Tensile Properties of Two Guide Bar Warp Knitted Fabric Reinforced Composites
Al/B4C Laminated Composite Fabricated by Powder Metallurgy Process and its Mechanical Property
Synthesis of Microporous-Mesoporous Carbons from Rice Husk via H3PO4-Activation
The Slagging Model Research of Refining-Slag for High Aluminum Steel
Evaluation of the Direct Tensile Behavioral Characteristics of UHPC Using Twisted Steel Fibers
Synthesis, Characterization and Optical Properties of Y6-xSmxMoO12+? Composite/Compounds Pigments with High Near-Infrared Reflectance
Effects of MoSi2 and Si3N4 on Performance of Sintering and Antioxidation of AlN-ZrO2 System Composites
Stress Characteristics Analysis on a Composite Wind Turbine Blade
Low Grade of Kyanite Ore Beneficiation Experimental Research in Xingtai
Application of Fiber Reinforced Composites for Wushu Equipment
Kyanite's Status of Beneficiation Process and Application
Research on Dual Liquid Bimetal Composite Casting Lining Board
The Research of Acoustic Characteristic from a Submerged Viscoelastic Functionally Graded Materials
Chapter 2: Micro/Nano Materials and Technology
Photocatalytic Reaction of SiO2/TiO2 Composite Core-Shell Structured Powders
The Effect of Cooling Rate During the Hydrothermal Growth on the Tip Geometry of ZnO Nanorods
Synthesis and Characterization of Silver Immobilized on Glass Fibers
Solid-State Chemical Reaction Synthesis and Characterization of Nanocrystalline CePO4 under Ultrasonication Spectra
Preparation of Polyurethane-Poly (Vinyl Alcohol) / Chitosan Blend Nanofiber Nonwovens by Coelectrospinning
Low Hydrogen Pressure Induced High Anisotropy in HDDR-Treated Nd13Fe75Co4B8 Powders
Infrared Extinction Properties of Randomly Oriented Columnar Nano-Graphite Particles
Study of Degradation of Photocatalytic Methyl Orange on Nano NdxCo2-xZr2O7
Influence of Nano Particle on Flexural and Impact Properties of Sandwich Structures
Study of Preparation of Nano NdxCo2-xZr2O7 and its Catalytic Properties on Ammonium Perchlorate Thermal Decomposition
Synthesis of Silicon Carbide Nanoparticles from Carbon Nanotubes
Silver Nanoparticles with Enhanced Fluorescence Effects on Fluorescein Derivative
Effect of Grain Size on Phase Transitions and Dielectric Properties of Nano-Crystalline Barium Titanate Ceramics
Preparation and Characterization of Nano-Ni/B Composite Particles
Effect of Mechanical Stresses on Metastability of Heterophase Superparamagnetic Nanoparticles
Preparation, Characterization of N-Ti-MCM-22 Molecular Sieve and its Photocatalytic Properties
Ultrasound-Assisted Solution Synthesis and Characterization of Sea Urchin-Like ZnO Hierarchical Microstructures
Applications of Nanostructured Materials as Additives in Space Fluid Lubricants
A New Numerical Method for Solving the Heat Conduction Equation in One Dimensional Nanometer Materials
Controllable Synthesis of Spheroid Hydroxyapatite Nanoparticles by Rverse Microemulsion Method
Preparation and In Vitro Drug Release Studies of Arginine Loaded Starch Microspheres
Effect of Lithium-Doped on the Crystal Structure and Morphology of ZnO Nanorod Arrays
Electrochemical Behaviours of Scutellarin at Multi-Wall Carbon Nanotubes Modified Glassy Carbon Electrode
Size and Interface Coherency Dependent Phase Transformation of Niobium Nanoparticles Embedded in Copper Matrix by Mechanical Alloying
Effects of Doped AE (Ca, Sr) on Synthesis and Structure of Lanthanum Chromite-Based Nano-Powder
Preparation and Properties of Organo-Montmorillonite Modified R-122 Nanocomposite
Preparation of the Silica Micro-Spheres by Chemical Precipitation Process
Preparation and Properties of Polypropylene/Expended Vermiculite Micro-Nano Composite
Effect of the Nanostructured Carbon Sorbent <<Ingo-2>> and Cadmium Chloride on Limfodynamic and Composition of Lymph
Application of a Mixture of Oxidized Multi-Walled Carbon Nanotubes and D-(-)-Tartaric Acid-Impregnated Silica Gel as Stationary Phases for Thin-Layer Chromatographic Enantioseparation
Application of Nano-Materials in Sports Engineering
Chapter 3: Steel and Iron Technology
Effects of Retained Austenite Stability on Mechanical Properties of High Strength TRIP Steel
Effects of Normalizing and Tempering Temperature on Mechanical Properties and Microstructure of Low Alloy Wear Resistant Steel Casting
Microstructure and Mechanical Properties of New Type Bainitic Carburized Steel for Gear
Effect of Tempering Temperature on Microstructure and Properties of Cold Deformed Low Carbon Bainitic Steel
Influence of Peeling Rates in the Nominal Bonding Strength between the Fabricated Composite and Stainless Steel Thin Film / Sheet
Study on Elevated Temperature Impact Properties of 20MnSiV Steel
Study on Austenitic Grain Growth for Heat Resisting Steel P91
Observation and Analysis of the Microstructures of IGF Refined Low Carbon Microalloyed Non-Tempered Steel
Effect of Intercritical Quenching Temperature on the Microstructure and Performance of 650 MPa Low-Carbon Structural Steel
Relationships between Fatigue Mechanical Properties and Roughness of Fatigue Fracture about 16MnR Steel after High Temperature
Effects of Controlled Rolling and Controlled Cooling on the Mechanical Properties of 550MPa Grade Engineering Mechanism Steel
Influence of Heat Treatment on Mechanical Properties and Microstructure of Mining Machinery Steel Plate Containing Molybdenum and Niobium
Analysis on the Cause for Fracture Lamination of 10CrNiCu Steel
Study on Sulfur Control Technology for Non-Oriented Electrical Steel
On the Presence of Eta Carbide in the Cryogenically Treated High Speed Steel
Analysis and Practical Application of Extracting Vanadium from Hot Metal in Steel Ladle
Methodical Basis of Investigation of Influence of the Iron Ore Materials and Coke Metallurgical Characteristics on the Blast Furnace Smelting Efficiency
Effect of Ce on the Inclusions and Pitting Resistance of 2Cr13 Stainless Steel
Effect of Two-Phase Region Quenching Temperature on Microstructure Evolution and Microhardness of HSLA100 Steel
Influence of Annealing Temperature on Microstructure and Properties of the Hot-Stamping Boron Steel
Research on Plastic Inclusions Control for Steel Cord
Research on the Effects of the Refining Treatment to the Properties of Dual-Phase Wear-Resistant Steel
Effect of Strain Rate on Dynamic Recrystallization Behavior for V Micro-Alloy High-Carbon Steel
Effects of Spray Forming and Aging Treatment on the Microstructures and Hardness of H13 Tool Steel
Effects of Quenching Medium on the Microstructures and Mechanical Properties of 42CrMo Steel
Effect of Welding Heat Cycle Peak Temperature and Heat Input on HAZ Grain Size of SMA490BW Corrosion Resistance Steel
Research on 304,321,316Lect. Stainless Steel Corrosion under the Calcinating Gas Atmosphere of Ammonium Paramolybdate
Study on the Tensile and Impact Properties of 600MPa HSLA Steel at Different Temperature
Mean Strain Effect on the Cyclic Stress-Strain Behavior of Steel Structure Materials Q235
Effect of Antimony on the Structure, Texture and Magnetic Properties of High Efficiency Non-Oriented Electrical Steel
Dynamic Recrystallization of 18Ni(1700MPa) Maraging Steel During Hot Deformation
Microstructure and Properties of Powder-Forged Steel
Thermodynamic Characterization in Intercritical Annealing Process for Dual-Phases Steels

In Situ Production of (Fe,Cr)7C3 Particulate Bundles Reinforced Iron Matrix Composites
Research on Test and Parameter Identification for Nonlinear Stiffness Characteristics of Leaf Spring
A Measurement Method for Magnetic Property of the Non-Oriented Silicon Steels
FEM Modeling and Validation of the Temperature Field in the Plasma Arc Bending of Laminated Clad Metal Sheets
Effects of Continuous Annealing Process on Microstructures and Properties of C-Mn-Si Bearing Cold-Rolled TRIP Steel
Optimization of CC Tail Bloom Operation
Research on High Efficiency Blowing Technology of 200t BOF
Research on the Microstructure and Properties for Nb-Contained Cold-Rolling High Strength Steel Sheet
Chapter 4: Ceramic
Resistivity and Dielectric Measurements of Pb(Mn0.5 W0.5)O3 Ceramics with Guard Ring Electrode
Effect of Nano-Nd2O3 on Sintering and Crystallization of Fused Quartz Ceramic Materials
Pressureless Sintering of B4C Neutron Absorbing Material with Nano-Sized Rare-Earth Compounds Addition
Study on the Synthesis of ZrAl3O3N and its Influencing Factors
Research and Development of Nano-Micro Composite Gradient Self-Lubricating Ceramic Cutting Tools
Preparation of Glass-Ceramics Using Industrial Solid Wastes in China
Effects of Sintering Time on Structure and Properties of 0.997(KNN-LS-BF)-0.003V2O5 Lead-Free Piezoelectric Ceramics
Biomorphic TiO2 Ceramics Prepared from Cotton Stalk
Influence of Mo Content on the Properties of TiC-Based Cermets
Effect of TiN Addition on the Microstructure and Mechanical Properties of Ti(C, N)-Based Cermets
Effect of Pressure of Nitrogen Atmosphere on Microstructure and Mechanical Properties of Ti(C, N)-12WC-16Ni-4Mo2C Cermet
Numerical Simulation of Failure Process of VITA All-Ceramic Crowns
Preparation, Characterization and Conductivity Studies of Li1.3M0.3Ti1.7(PO4)3 (M = Al, Cr and Fe) Glass-Ceramics
Chapter 5: Metal Alloy Materials
First-Principles Study on the Clean and Nb Doped TiO2(110)?-TiAl(111) Interfaces
Numerical Simulation for Dynamic Recrystallization of Ti40 Alloy in Hot Compression by Finite Element Method
Effects of Process Parameters on the Morphologies and Composition of Pulse Electrodeposition of Nickel-Rich Co-Ni Alloys
Effect of C6H4SO2NNaCO*2H2O on Microstructure and Electrochemical Properties of Electrodeposited La-Mg-Ni Alloys
Effect of Co-Doping on Electronic and Magnetic Properties in Ti2NiAl Heusler Alloy
Evaluation of the Protection Effect on Copper with Different Sacrificial Anodes
Research on Coupled Effects of Alloy Elements for Precipitation Strengthening to Rupture Life of Single Crystal Ni-Based Superalloys by RBF Networks
The Effect of Addition Mn on the Morphology of Fe-Rich Phase in the Al-1Fe Alloy
Connections of the Microstructure of the Fe-Al (25-33%wt.) with its Composition and Cooling Rate from the Liquid State
Preparation of Dispersion Strengthened Aluminum Alloy by High Energy Ball Milling
Effect of Equal Channel Angular Pressing on Microstructure and Properties of AZ61-4Si Magnesium Alloy
Microstructure and Mechanical Properties of Cu-Cr-Zr Alloy by Friction Stir Welding
Research on Precipitation Phenomenon of TiC and TiAl3 Particles in Aluminum Melt
The Study of Properties of Cu-0.8Cr-0.2Zr Alloy Used as Contact Materials
Microstructure and Mechanical Properties of Eco-2024-T3 Aluminum Alloy
Manufacturing and High Temperature Mechanical Properties of Inconel 713C by Using Metal Injection Molding
Parameters Affecting Dendrite Growth of Fe-C Alloy in a Forced Flow
DFT Study on Clusters Ni4-xFexP (x=0~4): A Theoretical Investigation on the Property of Amorphous Alloy Ni80-xFexP20
Chapter 6: Polymer Materials and Technology
Preparation and Water/Oil Repellency Properties of Waterborne Cationic Perfluorinated Polyacrylate
Dynamic Absorption and Desorption Research of HPD722 Macroporous Resin for Flavonoids in Thlaspi arvense Linn Extract
Effects of EVA-g-MAH on Mechanical Properties and Morphological Structure of TPU/PVC Blends
Synthesis and Characterization of a New Kind of UV-Curable Cyclohexanone-Formaldehyde Resins
Polyurethane Application in a Large-Scale LNG Tank
Study on Inhibition of Water Tree in XLPE Insulation Material
Study the Influences of ZnEt2 on Ethylene Chain Transfer Polymerization
An Orthogonal Experiment of Bagasse Cellulose Dissolution in Ionic Liquid by Microwave Heating
Time-Temperature-Stress Superposition Principle: Brief Description and Application to Polymer Creep Behavior
Study on Layered Structure and Properties of PP/LLDPE Injection Molding
Effect of Curing System on Morphological, Rheological, Thermal and Mechanical Properties of Thermoplastic Vulcanizates Based on Epoxidized Natural Rubber and Polypropylene
The Synthesis of Novel Oligomer 4,8-Di(4-hexyl-2-thienyl)-2?4?2-Benzo[1,2-c;4,5-c']bis[1,2,5]-Thiadiazole
Study on Network of Epoxidized Natural Rubber with Different Epoxidation Degree: Measured by 1H-NMR
Study on Preparation for Super Absorbent Polymer Using Cotton Waste
Effects of Bagasse Fiber on Crystallization, Morphological and Mechanical Properties of Poly(Lactic acid)
Laboratory Research of the Terpolymer Fracturing Fluid Gelatinizer
Using Optical Image Real-Time Analysis Software to Characterize Polymer Processing
Study on Increasing Conversion of Styrene/Butadiene Co-Polymerization by Adjusting Basic Recipe
Synthesis and Characterization of a Novel Star-Shaped Polymers with Biological Compatibility via Ring-Opening Polymerization and Atom Transfer Radical Polymerization
The Preparation and Characterization of AM/2-EHA/VTEOS Copolymer as Profile Control Agent
Synthesis and Properties of a Novel Cationic Polymer PTMAEPAC
Technics and Properties of Plywood Manufacture with Modified Urea-Formaldehyde Resin
MD Simulation of Crosslinked Epoxy Resin at Different Temperatures
Large-Scale Molecular Dynamics Modeling of a-SiO2
Chapter 6: Polymer Materials and Technology
Parameter Optimization for Vibration Flow Field of Polystyrene Melts via RBF Neural Networks Combined with SALS
The Synergistic Effect of Poly(Bisphenol phenyl dichlovophosphate) and Ammonium Polyphosphate in Flame Retardant ABS
Crystallization, Morphology and Mechanical Properties of PLA/PBAT/CaCO3 Composites
Miscibility and Thermal Properties of Bacterial Poly(3-Hydroxybutyrate-co-3-hydroxyhexanoate)/Poly(Ethylene oxide) Blends
Effect on Polymer Chain Structure Caused by the Molar Fraction of 4-Hydroxybutyrate in Poly(3-hydroxybutyrate- co -4-hydroxybutyrate)
Flocculation Effects of Hydrophobically Modified Polyacrylamides for Tailing Slurry
Indomethacin Molecular Imprinted Polymer Preparation, Characterization of Application
The Effect of Poly(Ethylene succinate) on Mechanical Property of PLLA/PES Composite in the In Vitro Degradation Process
Study on Properties of Sulfonate Hyperbranched Polymer Surfactant
The Effect of Thermal Aging on Properties of Epoxy Resin
Wood Plastic Composites Prepared from Poly(Vinyl Chloride) and Balau Sawdust (Shorea obtusa): Mechanical Properties and N-(?-aminoethyl)-?-aminopropyl trimethoxysilane Compatibilization
Chapter 7: Physics and Chemistry Materials and Technology
Terahertz Characteristics of Two Dimensional Photonic Crystal Cavity Based on 3D Finite-Difference Time-Domain Method
Elastomechanical Study of Magnetoeletric Coupling in Bilayer of Lithium Zinc Ferrite and Lead Zirconate Titanate
Luminescence Properties of Tm3+ /Dy3+ Co-Doped Zinc-Aluminum Phosphate Glasses for White LED
Characteristics of Photonic Crystals on the Total Reflection Tunneling with Material Absorption
Research of Fiber Radar Absorbing Materials
Research on Particle Size and Luminescence Properties of GdBaB9O16: Eu3+Phosphor Prepared by Sol-Gel Method
Fuzzy Ball Drilling Fluids for CBM in the Ordos Basin of China
Investigation and Evaluation on the Moisture-Absorption and Quick-Drying Properties of Stitch-Bonded Nonwoven Fabrics with Hemp/Polyester Blended Used in Shoe's Lining
Thermodynamic Study of Crystal Growth Behavior Based on Structural Analysis of Chemical Bonds
Influence of Pressure of Electron Gas on Elastic Property of Metal
Theoretical Study on the Interaction between Shuffle 60 degrees Dislocation and Hexavacancy in Silicon
Electronic Structures and Spectral Properties of the Optoelectronic Material Rhenium (I) Tricarbonyl Complexes Containing Spiro[Dipyridine-Fluorene]-Type Ligands
Adsorption of Methane on Pristine and Al-Doped Graphene: A Comparative Study via First-Principles Calculation
Characteristic of the Pigments in Castanea mollissina Shell
A New Methodology to Predict Energy Bandgaps in GaxIn1-xAsyP1-y Compounds by ANFIS Theories
Time-Dependent Density Functional Theory Studies of Plasmons in Parallel Double Sodium Atomic Chains
Studies on Extraction Equilibrium of Rare Earths in Ion Liquid Extraction System Using 1-Butyl-3-Methyl-Imidazolium Hexafluorophosphate and 1-Phenyl-3-Methyl-4-Benzoyl-Pyrazolone-5
Efficient Synthesis, Properties of a Novel Unsymmetrical Photochromic Diarylethene Based on Trifluoromethy Group and Formyl Group
Photoinduced Fluorescence Switching of a New Diarylethene and its Application in Optical Recording Storage
Synthesis, Properties and Application of a Photochromic Diarylethene with a Dithiolane Unit
Synthesize, Photochromic and Application for Optical Recording of Diarylthene Bearing Naphthyl Unit
The Composite Catalysts Used for Cotton Denim Resin Wrinkles Setting
Decomposition of Organic Dye in Water through a Heterogeneous Fenton Process Catalyzed by Fe (III)-Grafted PTFE Fiber Complex
Microwave-Hydrothermal Synthesis and Characterization of Graphene
Synthesis of Porous NiMo Sulphide Act as HDS Catalyst by Alcohol Supercritical Drying Technique
Chapter 8: Building Materials
Analysis of Marking Glass with Different Process Parameters Based on Super-Pulsed Laser
Experimental Research on Foamed Concrete Block with High Addition Crushed Brick Powder
Fresh Properties of Self-Compacting Concrete with Coarse Recycled Aggregate
The Adaptability Analysis of Cold Regenerated Structure Layer
Cooperative Performance of Sandwich Insulation Walls With Expanded Polystyrene Under Static Loads
Effects of Hydrogen Evolution During ECE on the Bond Strength between Steel and Concrete
Application of SHS-Refractories during Limestone Furnace Refurbishment
Effect of Curing Method on the Strength Development and Freezing-Thawing Durability of the Concrete Incorporating High Volume Blast-Furnace Slag Subjected to Initial Frost Damage
Optimum Mixture Ratio of Cement and Red Mud Stabilized Graded Crushed Stones Based on Grey Situation Decision
Effect of Quartz Powder on the Strength and Shrinkage of Alkali-Activated Slag Cement
The Influence of Temperature Sensitivity of Cold Recycling Materials on the Pavement Structure Mechanical State
Development of New Type Cementitious Materials Using as Road Base
A Study of Relationship Between Residual Asphalt in Aggregate Surface and Aging Degree of its Asphalt
Damage Pattern Recognition of Refractory Materials Based on k-Means Clustering Analysis
Evaluation of Burning Performance of the Traditional Organic Insulation Materials for External Wall of Buildings
Full-Scale Fire Testing of the Traditional Organic Insulation Materials for External Wall of Buildings
Microstructure of Autoclaved Aerated Concrete Hydration Products in Different Water-to-Binder Ratio and Different Autoclaved System
Bond Characteristics between ECC (Engineered Cementitious Composites) and GFRP Rebars
Study on Influence Factors of High Temperature and Water Stability of Stone Matrix Asphalt
Releasing Behavior of Chloride Ions in Marine Sands under Cement Environment
Chapter 9: Energy Materials and Fuel Technology
Development of Hydrogen Consumption Test Platform for Fuel Cell Vehicles
Application of the Fuel Cell in the Hybrid-Electric Vehicle
Modeling and Simulation of the Ni-Mh Battery
Optimization of the Synthesis Conditions of LiMnPO4 for Lithium Secondary Battery by Solid State Method
Preparation of High Performance Silicon/Carbon Anode Materials for Lithium Ion Battery by High Energy Ball Milling
Influence of TiO2 and Bio-Solution Based Additives on Exhaust Emissions of a DI Diesel Engine
Experimental Study on NO Emission Characteristics of Corn Stalk Combustion in O2/CO2 and O2/N2 Atmospheres
Performance Analysis of Single Stage Compression Cycle with a Throttle Valve, an Expander and an Internal Heat Exchanger
Performance Analysis of Single Stage Compression Cycle with an Internal Heat Exchanger
Research on Characteristics of Ethanol Gasoline Evaporative Emission
The Feasible Research on Solar Landscape Column
Resourceful Treatment of Dioscorea zingiberensis Wastewater Using a Double-Chamber Microbial Fuel Cell
Preparation and Performance of Myristic Acid/Silicon Dioxide Composites as Thermal Energy Storage Materials
The Simulation of Hydraulic Free Piston Engine Fueled with DME in HCCI Mode
Special Crude Oil Processing Research and Application of XinMu Oil Field
Study on Purification of Solar Grade Polysilicon
Chapter 10: Environmental Friendly Materials and Waste Recycling
Experiment and Research on the Waste Tire Rubber in the Whole Sugarcane Harvester
Preparation and Characterization on an Environment Friendly Used Rubber Powder Modified Pulp Sediments Composites
Extraction of Scandium from Red Mud Using ELM with P204 as Carrier
The Preparation of Composite Zeolite Filter
Research on Utilizing Environmental Friendly Materials of Barrier Board for Particle Reduction of High-Turbidity Raw Water
Methods of Improving the Interfacial Compatibility of the Bamboo Fiber/Thermoplastic
Mung Bean Germination and Three Different Food Waste Composting Processes
Review on Membrane Technologies for Carbon Dioxide Capture from Power Plant Flue Gas
Environmental and Economic Analysis of Valve Regulated Lead-Acid Batteries Recycling Process
Environmentally Friendly Materials: Aerobic Composting of Kitchen Waste
Synthesis and Adsorption Property of Graphite Oxide Modified GF/EPDM Foamed Composite
Preparation and Adsorption Performance of GF/EPDM/LLDPE Foaming Composite for Petrol
Study of Environmentally Friendly Phosphate-Bonded No-Bake Sand
The Status of Nonylphenol Pollution in Lotic Ecosys-Tem
The Experimental Study of Contaminant Removal in Water Quenched Slag Biological Aerated Filter (BAF)
Development and Prospect of Al Scraps Reproduction Technology in China
Chapter 11: Biomaterials
Studies on Bending Limitations for the Optimal Fit of Orthopaedic Bone Plates
Preparation and Characterization of Immobilized ?-Amylase
Production of Biodegradable Board Using Corn Straw and its Mechanical Properties
Wound Healing Activity of Carbonized Rice Husk
Effect of Heating Treatment of Fresh Rice Bran on Stabilization
Freeze-Thaw Stability of Oil-in-Water Prepared with Soy Protein Isolate-Maltodextrin Conjugates
A Study on Adsorption Ammonia Nitrogen of Diatomite Modified by Microwave
Preparation of Vitamin C Dripping Pill and its Quality Evaluation
Pore Size Gradient Hydroxyapatite Scaffolds with Interconnected Pores Fabricated by a Template Method
Extraction of Elopichthys bambusa Oil with Various Methods
Study on the Biodegradability of Protein Fibers and Their Products in Activated Sludge
Chapter 12: Chemical Materials and Processes
Study of the Catalytic Effects of Trace Titanium on Oxidation of Pyronin B with Hydrogen Peroxide and its Application
Preparation and Property Evaluation of Anionic Clean Fracturing Fluid
Effects of Hydrolysis Parameters on TiO2 White Pigment from Low Concentration Industrial TiOSO4 Solution via Sulfate Process
MFR High Temperature Profile Control Agent Experimental Evaluation
Influences of Hydrolysis Temperature and Hydrolysis Time on Titanium White Pigment via Short Sulfate Process
The New Synthesis of Organic Light-Emitting Material BHBT Monomer by Stille Coupling
Removal of Chemical Oxygen Demand in Tannery Effluent by Flocculant
Improved Synthesis of 3,3-Dimethyl-4-Pentenoic Acid Methyl Ester
Synthesis and Characterization of Comb-Type Grafted Hydrogels
Morphology and Release Profile of Microcapsules Encapsulated Alpha-Pinene by Complex Coacervation
Kinetic Spectrophotometric Method for the Determination of Trace Ruthenium(III) by its Catalytic Effect on the Oxidation of Dibromo Caboxy Arsenazo with Bromate in Cationic Micellar Media
Preparation of Carbon Source Doped in Polymer-Cement Filter and Research on Characteristic of Denitrification
Simulation on Application of Dividing Wall Column in Aniline Distillation
Study on Synthesis of High Performance Emulsion of Paper Sizing Agent under Microwave Radiation
Study on Gas Control in Coal Mine by Methanotrophic Bacteria M02
Analysis of Volatile Compounds in Flowers of Akebia trifoliata by Headspace Solid-Phase Microextraction Coupled to Gas Chromatography-Mass Spectrometry
Numerical Study on Formation Mechanism and Reduction Methods of NOx in Methane/Oxygen-Enriched Air Diffusion Flame
Study on Property of Acid-Modified Kudzu Starch
Study on White Mud Calcium Carbonate's Crystallization Character in Causticization Process of Straw Pulping
Research on Preparing Lithium Carbonate by Carbonation from Lithium Chloride in Biphase System
Preparation and Characterization of Sodium Hexatitanate Whiskers
Experiment and Micro-Mechanism Research of Fe2O3 Catalysis in Flue Gas Desulphurization in Magnetically Fluidized Bed
Synthesis of AM-co-NVP and Thermal Stability in Hostile Saline Solution
Template Synthesis to Fabrication of 3D Ordered Hierarchical Materials
The Oxidation Erosion in Carbon Materials for CZ Furnace
Study on Simulation of Nitrobenzene Distillation Using Dividing Wall Column
Study on the Preparation of Calcium Sulfate Whisker by Hydrothermal Method
Synthesis of Several Sugar Acetates and their Structures Characterization
Investigation of Low-Cost Copper Interconnection Cleaning Using Hydrogen Radicals Generated by Heated Catalyst
Study on Preparation of Modified Ti-Based Lead Dioxide Electrode and Degraded Methylene Blue
The Plasma Electrolytic Oxidation Process in K2ZrF6 with Na2HPO4 Electrolyte
The Purification and Analysis of 6 - Hydroxy -2 - Naphthoic Acid
Chapter 13: Thin Films
Effect of Substrate Temperature on the Opto-Electrical Propertites of Ti Doped ITO Films Deposited by RF Magnetron Sputtering
Effects of Substrate Temperature on Structure and Properties of Al-F Co-doped ZnO Thin Films
Influence of Deposition Time on the Properties of Highly-Oriented SnS Thin Films Prepared Using the Thermal Evaporation Method
Synthesis and Photocatalytic Properties of TiO2 Film with Hierarchical Structure Prepared by Sol-Gel Method
Point Defect States of Phononic Crystal Thin Plates - An Application of Finite Element Method
Ni-Doping Effect on the Structural and Optical Properties of Sprayed ZnO Thin Films
Thermal Effects Induced by Absorbing Inclusions in Laser Optical Films
Investigation of Co-Sputtered Amorphous NbxSi1?x Films Properties for Junction Barrier
Influence of Laser-Conditioning on Laser-Induced Damage Properties of ZnSe Thin Films
Experimental Study on Dynamic Measurement of ELID Oxidation Film Thickness Based on LabVIEW
Investigation of Microstructure, Electrical and Decorative Properties of WO3 Film by PVD Magnetron Sputtering with Ar/O2
Temperature Dependence of Raman Scattering in M-Plane GaN with Varying III/V Ratios
Simulation of the Growth, Structure and Crystallization of the Amorphous Silicon Thin Film
Effects of Annealing Temperature on Structure and Properties of PLBZT Ferroelectric Thin Films Synthesized by Sol-Gel Processing
Chemical Structure of Fluorocarbon Films Deposited by Pulsed Plasma Thruster
Research of Preparation and Etching of PS Microspheres Film
Effect of Annealing Temperature on Structural and Electrical Properties of Bismuth Ferrite Thin Film
Chitin Nanofibers / Epoxy Resin Optically Transparent Nanocomposite Films
Fabrication of Polyelectrolyte/TiO2 Hybrid Membrane via a Simple Method and Characterization of its Thermal Behavior
A Simple Model for Mechanical Behavior of PET Thin Film Deposited with Pure Aluminum on Both Surfaces and the Experimental Study
Study on Properties of Dye-Sensitized TiO2 Films
Research on Property of Polyvinyl Alcohol Sustained-Release Film
Influence of Annealing Time on the Properties of GZO Thin Films Fabricated by Direct Current Magnetron Sputtered
Packaging Films of Modified Polyethylene by Nano SiO2-EVA
Chapter 14: Earthquake Resistant Structures, Materials and Design
Effect of Laminar Flow to Velocity Exponent of Viscous Damper
Influence of Silicon Content on Microstructure and Damping Capacity of Fe-Cr Based Damping Alloy
Numerical Study of Stone Column Reinforced Composite Foundation of Highway under Static and Seismic Load
Liquefaction Analysis of Large Diameter Long Pile Foundation in Medium Dense Sand under Earthquake Based on Finite Difference Method
Research about Efficiency of Seismic Mitigation for FPS-TMD System
Analysis about Isolation Floor Consisting of FPS System and Dish Spring
Influence of the Strain Hardening of HDRBs in the Evaluation of the Seismic Response of a RC Base Isolated Structure
Assessment of the Seismic Vulnerability of Existing RC Buildings and Effect of the Irregular Position of the Masonry Panels on the Fragile Collapse Mechanisms
Behaviour of Shearwalls with Slabs and Openings
Study on the Grouting Reinforcement and Stability of a Tailings Initial Dam
Retrofitting Options for Un-Reinforced Brick Wall Subjected to Impact Load
Seismic Performance of a Multi-Story Composite Frame with Partial Shear Interaction and Partial Strength Joints
Seismic Strengthening of Non-Ductile R/C Structures Using Infill Wall or Ductile Steel Bracing
Chapter 15: Surface Engineering/Coatings
Study on Sealing Technology for Micro-Arc Oxidation Ceramic Coatings of Aluminium
Analysis on Functionally Graded Material Coating Interface Crack
Investigation of Surface Roughness in Hardened GCr15 Steel Turning with Mixed Ceramic Insert
Densification and Purification of Cold Sprayed Ti Coating Layer by Using Annealing in Different Heat Treatment Environments
Repair Technology of Shafts in Boats and Ships
Structure and Properties of Ti/TiN/Sb-SnO2 Electrodes with Plasma Sprayed TiN Interlayer
Paper and Board Pigment Coating Raw Materials - A Review of some Recent Innovative Novelties
Determination of Coated Substrate Roughness by Quantification of Measured Depth Profiles
Preparation of Glass-Ceramics of Li2O-Al2O3-ZnO-SiO2 System Coating Toughed by ZrO2 Basic on Metal Substrate
The Progress and Development Direction of Adding Ball Methods
Research on Micro-Structure of Electroless Ni-B Coatings
A Comparative Study: Effects of Two Different Surface Engineering Technologies on Tribological Properties of Pure Titanium
Improvement and Sensitivity Analysis of Placement Angle Optimization in Physical Vapor Deposition Process
Hydrophilic/Hydrophobic Behavior on Ti Foil Surface Prepared by Anodization
Fabrication and Properties of Cu-Cr Coatings on the Inner Wall of Steel Pipe by Mechanical Alloying Method
Erosion Experimental Study on Organ-Pipe Nozzles in Air
Preparation of Two-Package Inorganic High-Temperature Paint
Preparation of High-Temperature-Resistance Silicone Paints
Electro-Spark Deposition of Composite TiB2-TiC on Electrodes' Surface
A Convenient Strategy to Control the Specific Surface Area of the Mesoporous Silica by Using the Poly(pseudo)rotaxanes Template
Tension in Surface Layer of Workpiece by Different Tool?s Geometry
Surface Modification of Magnesium Hydroxide with Stearic Acid
Mechanical Milling Prepared Nano-Sized Al2O3 Particles Utilized in Electroless Plating Ni-P- Al2O3 Composite Coatings
Surface Redox Initiated Polymerization to Prepare the Poly(N-isopropylacrylamide) Coating
Effects of Fuel Gas on the Microstructure and Mechanical Properties of HVOF Spraying WC-12Co Coating
The Influence of Supports on the Surface Properties of PtNi Bimetallic Catalysts
The Preparation of Silver-Spray Plated on PET Filament
Study on the Properties of Polyester Fabric by Ni/Co/Fe Multilayer Electroless Plating Technology
Chapter 16: Modeling, Analysis and Simulation
Three Numerical Simulation Methods on Dynamic Free Surface Deformation Simulation of a Sessile Drop
Computation and Simulation of 5-Axis Cutter Based on Scattered Point Cloud Data
ME Molecular Dynamics Simulation of the Sintering Process of the Porous ITO Material
Structural and Shaping Design of Centerless Cylindrical Grinding Machine Based on CAD
An Efficient Algorithm Design for the One-Dimensional Cutting-Stock Problem
Modeling and Analysis on the Rotation Accuracy of Lathe Spindle
Numerical Simulation of Bionic Wing for Drag Reduction
Numerical Simulation and Online Window Monitoring of SPR Process
Numerical Simulation of Heat Flow in a Vehicle Cabin
EBD Control Research on Nonuniformity Roads for Electric Vehicles on Energy Regenerative and Feedback Friction Integrated Braking
Chaotic Cat Swarm Algorithms for Global Numerical Optimization
Chaotic Grenade Explosion Algorithms for Global Numerical Optimization
Homotopy-Inspired Cat Swarm Algorithm for Global Optimization
Homotopy-Inspired Grenade Explosion Algorithm for Global Numerical Optimization
Study on On the Cross-Sectional Shape Change of the Profiled Fiber along the Spinning Path in Melt Spinning
Quantification of N2+ Implanted AES Depth Profiling Data in Al
The Impact of Roundness of Granular Materials on Physical Modeling Results
Research on NX-Based Progressive Die Design
Shifting Analysis and Simulation of Automated Mechanical Transmission without Separating Clutch
Ship Lines Modeling Theory of High-Speed Ship Based on the Partial Differential Equations
A Production Scheduling Framework Integrated with Simulation Module
Chapter 17: Materials Forming and Processes
Study of the Mechanical Properties for an Automotive Part under Squeeze Casting Process
Numerical and Experimental Investigation into the Aluminum Alloy Irregular Box Sheet Hydroforming Process
Numerical Simulation for Precision Roll-Forging of Automobile Front Axle
Fabrication of Aluminum Clad Copper Tube by Planet Schrage Walzwerk Process
Numerical Simulation of Springback in Stretch Forming with Two Different Grippers
Numerical Simulation on Rolling Process of Medium Plate
Optimization Design of Forging Die for Supporting Bar Based on DEFORM-3D
Phase Field Simulation of Solidified Multiple Grains
Simulation Study and Optimization of Process Parameters in Precision Forming of the Nut Plate
Research on the Manufacturing Process of the Whole Fiber Hollow the Trailer Axle
Effect of Coil Parameters on Rivet Deformation in Low Voltage Electromagnetic Riveting
Research on Roll-Forging Process Simulation for Thick-Walled Hollow Part
Research on Algorithm of Forming Limit Height in Semi-Ball Bottom Cylindrical Deep Drawing
Numerical Simulation of Stamping Forming for an Automobile Reinforced Plate Based on Orthogonal Test
Numerical Simulation of Residual Stress during Stamping-Forging Forming of 2024 Aluminum Alloy Sheet Metal
Numerical Simulation Research on Warm Forging Process for Spur Gear with Large Module Based on Floating Die Method
Filling Pattern of Step Gating System in Lost Foam Casting Process and its Application
Design of Die-Casting Die with Double-Stage Linkage Hydraulic Core-Pulling Mechanism
The Process Analysis of Commonly Used T-Shaped Tube Compound Bulging Media
Modeling and Analysis of Process Parameters for Plastic Injection Molding of Base-Cover
Methods of Establishing Forming Limit Diagram of Tube Hydroforming
Research on Intelligent Precise Pass Design Algorithms
Research on the Forming Process of the Y-Shaped Tube Based on ABAQUS
The Effect of Drawing Process on the Properties of Split-Film PTFE Fiber
Numerical Simulation of Discrete Die Bending of Rectangular Tube
Finite Element Analysis on Flanging Forming of Car Spoke Parts
Numerical Simulation on the Microstructure during Extrusion Process of P91 Large Diameter Thick-Walled Tube
Chapter 18: Materials Machining
Model of Shear Slipping Deformation and its Cutting Energy Consumed for High Speed Machining
Precision Grinding Characteristics and Process Optimization on YG3 Cemented Carbide
Study on 22MnB5 Steel Microstructure in Hot Forming Progress
ANSYS Application in Cutting Stiffness Analysis of a Gearbox's Back Case
Study on the Mechanism and Tool of the Uniform ER Finishing with Changeable Removal Rate Model of Free-Form Surface
Optimal Selection of Machining Parameters by Genetic Algorithms for Face-Milling Operations Based on Minimum Unit Machining Time
Study on Drill-Through Determination in Vibration Drilling Based on Axial Force
Turn-Milling Parameters Optimization Based on Cutter Wear
Quality Research on Electric Discharge Machining with Rotary Surface of Engineering Ceramic
The Hot Deformation Behavior and Hot Processing Map of CL60 Rail Wheel Steel
Experimental Research on the Relation between Processing Parameters and Fractal Dimensions of the Machined Surface
Study of the Impact Toughness Experiment of SiCp / Al FGM
Simulation and Experimental Study on Size Effect in Steel Micro Milling Machining Process
Research on Surface Roughness Experiment of Flank Milling for the Ruled Surface Blade
The Application of Enamel Material in the Jewelry Industry
Preparation of Al2O3/Cu Composites by Internal Oxidation in Cu-Al Alloy Sheet Processing
Laser Micro-Jet Processing on Red Copper
Combined Setting Technology of the Bending Roll in Five Stands 4-High Reduction Cold Mill
Proportional Crown Rolling for Single Rough Stand in Semi-Continuous Hot Rolling Strip
Study on Manufacturing Technology of Resin Bonded Diamond Wire Saw
Chapter 19: Welding and Joining

In Situ Detection of Thermal Cycle in Weld Metal of Cr-Mo Steel
Numerical Simulation on Interface Crack Propagation for Non-Uniform Welded Joint
Vacuum Brazing of Zircaloy-4 and Stainless Steel Using Ag-Cu-Ti Brazing Filler Metal
Mathematical Model of Ti-6Al-4V Single Track Formed by Selective Laser Melting
Characteristics of Surface Microstructures for Welded Joint of 7A52 Aluminum Alloy before and after Surface Nanocrystallization
Analysis on the Refractory Erosion of the Electric Arc Furnace and Study on the Measures of Protecting the Furnace Lining
Vacuum Brazing of GH2132 Superalloy Using BNi-2+BNi-5 Composite Filler
Effect of Metal Block on Stress Distribution in Weld-Bonded Steel Joint
Effect of Shock Temperature on the Impact Toughness of Butt-Joint
On Copper-Steel Joint Arc Welded with Nickel Based Filler
Process Analysis of the Electric Arc Furnace Melting for Alumina Spinel Production
The Vehicle Modal Analysis and Test Verification Based on Weld Joints Simulation
Study on the Residual Stress of LY12 Welded Component
State-of-the-Art of Joining Technologies for Assembled Camshaft
Effects of Welding Time and Alloy Elements on Mechanical Properties of Aluminum/SPCC Joint Using Resistance Spot Welding
Solidification Behavior and Phase Relation of Arc Melting La-Fe-Si Alloys
Effects of Filler Metal on the Microstructures and Properties of 2519A/7A52 Weld Joint
The Influence of Different Factors on the Stress Distribution of Strip Joints
Chapter 20: Mechanical Behavior and Fracture
Finite Element Analysis for Mechanical Part of Metal Embedded Resin Mineral Composites
The Analysis for Influence of Connecting Rod Strength with the Change of Interference of Connecting Rod Small End Bushing
Elastic-Plastic Analytical Solution of Deep-Buried Circle Pervious Tunnel Based on Unified Strength Theory
Stress Calculation for Large Storage Oil Tanks' Shells Based on the Theory of Short Cylindrical Shell
The Analysis of the Deformation and Contact Lubrication Problem of HPD Diesel Engine Connecting Rod Bearings Based on the FFT Method and Flexibility Matrix Method
Analysis of Motion Process of Incompact Landslip-Collapse Soil
Dynamic Anti-Plane Characteristic for a Quarter-Infinite Piezoelectric Medium with a Cylindrical Lining
Influence on the Stress of Pavement with Crack in Surface from Flexible Transition Layer under Dynamic Loading
Influence on the Stress of Pavement with Crack in Base from Flexible Transition Layer under Dynamic Loading
Predicting Fatigue Crack Initiation Life of Plate-Like Component by Coupied Variational Principle
Research on the Wear Morphologies of NBR/FKM Blend under Dry Friction
Notch Fracture Behavior of Cold-Rolled Ni3Al Foil
Research on the Mechanism between No-Smooth Surface, Desorption and Friction Increasing Based on Bionic
Friction and Wear Behaviors of Copper Rubbing against Carbon Material with and without Windy Conditions
FEM Simulation and Experimental Verification on Rotating Forging of Three-Layer Clad Cylinder Considering Constant Shear Friction
Study on Failure Mechanism of Steel Wire Wound Reinforced High-Pressure Hose
Study on Optimal Winding Angle of Submarine Oil Flexible Pipe
Lightweight Analysis of Automotive Anti-Collision Materials Based on Equal Energy Absorption Strategy
Features of Meso-Deformation and Failure of Aluminum Foam under Impact
Elastic-Plastic Fracture Assessment for the Cracks Emanating from a Circular Hole under a Biaxial Loading Condition
Elastic-Plastic Analysis and Failure Assessment of the Pipeline Steel with Surface Crack
Chapter 21: Tooling Testing and Evaluation of Materials
Validation of a Phenomenological Lifetime Estimation Method with Biaxial Experiments at High Temperature
Research of Comparison Circular Interpolation on WINCE
An Optimization Approach for 25um Pitch Microbolometers
Grey Clustering Model of Coating Erosion Resistance Evaluation
The Impact of Drying Methods on Paper Physical Properties
Steel Wire Grinding Testing Based on New Type Abrasive Belt Grinding Machine
Numerical Analysis on the Butt-Joint under Izod Impact Test
Simulation and Experimental Research of Sheet Metal Defect Detection Based on Ultrasonic Lock-in Thermography
Study on Microwave Combined with Granular Active Carbon for Treatment of P-Nitrophenol Wastewater
Research on Anti-Creasing Properties of 100% Cotton Yarns