
High-Performance Ceramics IV
Trans Tech Publications Ltd (Publisher)
Published on 6. April 2007
Book
Paperback/Softback
2800 pages
978-0-87849-410-1 (ISBN)
Article exhausted; check different version
Description
Volume is indexed by Thomson Reuters CPCI-S (WoS).
Volume is indexed by Thomson Reuters CPCI-S (WoS).
More details
Series
Language
English
Place of publication
Zurich
Switzerland
Target group
College/higher education
Professional and scholarly
Dimensions
Height: 24.5 cm
Width: 17 cm
Thickness: 140 mm
Weight
6000 gr
ISBN-13
978-0-87849-410-1 (9780878494101)
DOI
10.4028/www.scientific.net/KEM.336-338
Schweitzer Classification
Other editions
Additional editions

Wei Pan | Jiang Hong Gong
High-Performance Ceramics IV
E-Book
04/2007
Trans Tech Publications Ltd
€211.86
Available for download

Wei Pan | Jiang Hong Gong
High-Performance Ceramics IV
Software
04/2007
Trans Tech Publications Ltd
€881.17
Shipment within 10-20 days
Content
<ul><li>Processing, Properties and Possible Applications of PZT-Based Thin Films</li><li>High Piezoelectric Property and Low Dielectric Constant PZN-PZT Ceramics</li><li>Molten Salts Synthesis of Relaxor Ferroelectrics PMN-PT Powders</li><li>Effect of PbO-Based Glass Frit Additives on Physical and Electrical Properties of 0.125PMN-0.875PZT Piezoelectric Ceramics near the Morphotropic Phase Boundary</li><li>Electrical Properties of (1-x)(0.8PMN-0.2PNN)-xPT Ceramics near the Morphotropic Phase Boundary</li><li>Effects of Rare Earth Gd Doping on Ferroelectric Properties of PbZr<sub>0.52</sub>Ti<sub>0.48</sub>O<sub>3</sub> Thin Films Prepared by Sol-Gel Methods</li><li><001> Textured Pb(Mg<sub>1/3</sub>Nb<sub>2/3</sub>)O<sub>3</sub>-PbTiO<sub>3</sub> Ceramics Prepared by Reactive Templated Grain Growth</li><li>The Effect of Zn<sup>2+</sup> Deficiency on Ordered Micro-Regions and Dielectric Properties of Pb(Zn<sub>1/3</sub>Nb<sub>2/3</sub>)O<sub>3</sub>-Based Relaxor Ceramics</li><li>Structure and Electrical Properties of Pb(Ni<sub>1/3</sub>Nb<sub>2/3</sub>)O<sub>3</sub>-Pb(Zr/Ti)O<sub>3</sub> Relaxors</li><li>Pb(Mg<sub>1/3</sub>Nb<sub>2/3</sub>)O<sub>3</sub>- Pb(Ni<sub>1/3</sub>Nb<sub>2/3</sub>)O<sub>3</sub>-PbTiO<sub>3</sub> Crystals by Solid State Growth</li><li>Effect of Different Doping on the Structure and Field-Stability of PMNT Ceramics</li><li>Structure and Electrical Properties of Rapid Thermally Annealed PZT Films Deposited through Sol-Gel Process</li><li>Dielectric Properties and Phase Transition of [110]-Oriented 0.68PMN-0.32PT Single Crystals Induced by Temperature and DC Electric Field</li><li>Preparation of Pb(Mg<sub>1/3</sub>Nb<sub>2/3</sub>)O<sub>3</sub> Relaxor Ferroelectric by Sol-Gel Route</li><li>Dielectric Properties of (Bi<sub>1/2</sub>Na<sub>1/2</sub>)TiO<sub>3</sub>-SrTiO<sub>3</sub> Ferroelectric Ceramics</li><li>Dielectric Properties of Y<sup>3+</sup>-Doped Ba<sub>0.62</sub>Sr<sub>0.38</sub>TiO<sub>3</sub> Ceramics</li><li>Piezoelectric and Dielectric Properties of (Bi<sub>0.5</sub>Na<sub>0.5</sub>)TiO3- (Bi<sub>0.5</sub>K<sub>0.5</sub>)TiO<sub>3</sub>-BaTiO<sub>3</sub> Lead-Free Piezoelectric Ceramics</li><li>Investigation of Field-Induced Piezoelectric Properties in Pb(Mg<sub>1/3</sub>Nb<sub>2/3</sub>)O<sub>3</sub>-PbTiO<sub>3</sub> Ceramics for Transducer Applications</li><li>Low Temperature Sintering (Ba<sub>1-x</sub>Sr<sub>x</sub>)TiO<sub>3</sub> Ceramics by Using CuO-TiO<sub>2</sub> Mixture as Sintering Aid</li><li>Preparation of Plank-Like BaTiO<sub>3</sub> by Hydrothermal Soft Chemical Process from Layered Titanate Precursors</li><li>Preferred Orientation Growth of Ba<sub>0.6</sub>Sr<sub>0.4</sub>TiO<sub>3</sub> Thin Films with Epitaxial MgO Buffer Layer on Si(100) Substrate</li><li>Reliability of Ba(Zr<sub>0.1</sub>Ti<sub>0.9</sub>)O<sub>3</sub> Ferroelectric Thin Films under Various Frequencies for Nonvolatile Memory Application</li><li>Preparation and Characterization of Citrate Sol-Gel Derived Ba(Zr,Ti)O<sub>3</sub> Ceramics with Al<sub>2</sub>O<sub>3</sub> Addition</li><li>Effect of Deposition Parameters on Crystallization of RF Magnetron Sputtered BST Thin Films</li><li>The Effect of Different Doping Methods of Sintering Aids on the Barium Titanate Based X7R Ceramics</li><li>Preparation of Ferroelectric BaTiO<sub>3</sub> Films by Electrophoretic Deposition Technique</li><li>Preparation and Dielectric Properties of the Nb and Co Doped Barium Titanate by Sol-Gel Auto-Ignition Synthesis Process</li><li>Fabrication of (Ba,Sr)TiO<sub>3</sub> Thin Films by Hydrothermal Crystallization of Sol-Gel Precursor</li><li>Dielectric Properties of HGRP BaTiO<sub>3</sub> Based X7R Materials</li><li>Synthesis and Characteristics of Infrared-to-Visible Upconversion Nanoparticles through a Microemulsion System</li><li>Influence of Different Dopants on the Piezoelectric Properties of the Na<sub>1/2</sub>Bi<sub>1/2</sub>TiO<sub>3</sub>-BaTiO<sub>3</sub>- Lead-Free Ceramics</li><li>Tape Casting of Ba<sub>0.7</sub>Sr<sub>0.3</sub>TiO<sub>3</sub> for Tunable Microwave Devices</li><li>Electrophoretic Deposition Ba<sub>0.65</sub>Sr<sub>0.35</sub>TiO<sub>3</sub> Thick Films for Tunable Microwave Devices</li><li>(Ca,Sr,Ba)TiO<sub>3</sub>-Based Dielectrics Sintered in Reducing Atmosphere</li><li>Electric and Damping Properties of PU Based IPNs-BaTiO<sub>3</sub> Nanocomposites</li><li>Texture Development in Na<sub>1/2</sub>Bi<sub>1/2</sub>TiO<sub>3</sub>-BaTiO<sub>3</sub> Ceramics by Reactive-Templated Grain Growth</li><li>Effect of Sr/Ba Ratio on Dielectric Properties of BSTN Ceramics</li><li>The Influence of Thin Film Thickness on the Characteristics of Bismuth Titanate Oxide</li><li>Structure and Dielectric Properties of Homogeneous Sr<sub>m-3</sub>Bi<sub>4</sub>Ti<sub>m</sub>O<sub>3m+3</sub> (m = 3, 4, 5, and 6) Ceramics</li><li>The Influence of Precursor on the Microstructure and Characterization for Sr<sub>0.5</sub>Ba<sub>0.5</sub>Bi<sub>4</sub>Ti<sub>4</sub>O<sub>15</sub> Thin Films</li><li>Synthesis and Properties of (Bi<sub>0.5</sub>Na<sub>0.5</sub>)TiO<sub>3</sub> Powders by Hydrothermal Method</li><li>Fabrication and Properties of SrBi<sub>2</sub>(Ta<sub>1-x</sub>Nb<sub>x</sub>)<sub>2</sub>O<sub>9</sub> Ferroelectric Ceramics</li><li>Study on Ferroelectric Properties of Nd-Doped Bi<sub>4</sub>Ti<sub>3</sub>O<sub>12</sub> Thin Films Prepared by Sol-Gel Method</li><li>Electrical Characteristics and Microstructures of Gd-Doped Bi<sub>4</sub>Ti<sub>3</sub>O<sub>12</sub> Ceramics</li><li>Electrical Characteristics and Microstructures of Nd<sub>2</sub>O<sub>3</sub>-Doped Bi<sub>4</sub>Ti<sub>3</sub>O<sub>12</sub> Thin Films</li><li>Dielectric Characterization and Microstructures of Pr<sub>6</sub>O<sub>11</sub>-Doped Bi<sub>4</sub>Ti<sub>3</sub>O<sub>12</sub> Thin Films</li><li>Dielectric Characteristics of Doped Strontium Titanate within Broad Temperature Range</li><li>Hydrothermal Preparation of Bismuth Titanate Nanopowders</li><li>Fabrication of Bi<sub>3</sub>NbTiO<sub>9</sub> Thick Films by Air Flow Deposition</li><li>The Crystalline, Dielectric and Pyroelectric Properties of (1-x)Pb(Sc<sub>0.5</sub>Ta<sub>0.5</sub>)O<sub>3</sub>-xPb(Zr<sub>0.52</sub>Ti<sub>0.48</sub>)O<sub>3</sub> Relaxor Ferroelectric Ceramics</li><li>Epitaxial Growth and Electrical Characterization of PBZT Thin Films by RF Magnetron Sputtering Deposition</li><li>Microstructure Characteristics in the BaTiO<sub>3</sub>-La<sub>2</sub>O<sub>3</sub>-Nb<sub>2</sub>O<sub>5</sub> Ternary System</li><li>Ferroelectric Properties of Bi<sub>3.4</sub>Y<sub>0.6</sub>Ti<sub>3</sub>O<sub>12</sub> Thin Films Prepared by a Modified Sol-Gel Process</li><li>Phase Structure and Electrical Properties of Bi<sub>1/2</sub>Na<sub>1/2</sub>TiO<sub>3</sub>-KNbO<sub>3</sub> Lead-Free Piezoelectric Ceramics</li><li>Sintering and Dielectric Properties of Excess Bi<sub>2</sub>O<sub>3</sub> Doped BaBi<sub>2</sub>Nb<sub>2</sub>O<sub>9</sub> Ceramics</li><li>Preparation of Bi-Layered SrBi<sub>2</sub>Ta<sub>2-x</sub>V<sub>x</sub>O<sub>9</sub> Ceramics (0.1 ? x ? 0.4)</li><li>Microwave Dielectric Properties of Ca[(Li<sub>1/3</sub>Nb<sub>2/3</sub>)<sub>0.95</sub>Zr<sub>0.15</sub>]O<sub>3+?</sub> Ceramics with Ba<sup>2+</sup> Substitution at A-Site</li><li>Influence MnO<sub>2</sub> on the Properties of (Li<sub>x</sub>Na<sub>y</sub>K<sub>1-x-y</sub>)NbO<sub>3</sub> Ceramics</li><li>Preparation of Ferroelectric K<sub>0.5</sub>Na<sub>0.5</sub>NbO<sub>3</sub> Films by Sol-Gel Processing</li><li>Composition Range of Morphotropic Phase Boundary and Electrical Properties of NBT-BT System</li><li>Effects of Processing Conditions on the Dielectric Properties of CaCu<sub>3</sub>Ti<sub>4</sub>O<sub>12</sub> Ceramics</li><li>Preparation and Characterization of LiNbO<sub>3</sub> Thin Films Derived from Metal Carboxylate Gels</li><li>Bridgman Growth of a Novel Piezoelectric Single-Crystal Material: Ca<sub>3</sub>NbGa<sub>3</sub>Si<sub>2</sub>O<sub>14</sub></li><li>Preparation and Properties of (La, Sr) MnO<sub>3</sub> Thin Films Prepared by Sol-Gel Method</li><li>Na<sub>1-x</sub>K<sub>x</sub>NbO<sub>3</sub> (x=0.2~0.8) Lead-Free Piezoelectric Ceramics Prepared by Spark Plasma Sintering</li><li>Effect of TiO<sub>2</sub> Nanopowders on the Sintering and Electric Properties of Lead Zirconate Titanate Ceramics</li><li>Stability of the Perovskite Structure in BSPT-Based Ferroelectric Ceramics</li><li>Properties of Ultrafine High Curie Temperature (1-x)BiScO<sub>3</sub>-xPbTiO<sub>3</sub> Ferroelectric Ceramics</li><li>Preparation of Composite Ceramics of NiFe<sub>2</sub>O<sub>4</sub>/PZT by Sol-Gel Method and their Magnetoelectric Effect</li><li>Investigation of High-Quality ZnO Film on Polycrystalline Diamond Wafer for Fabrication of High Frequency SAW Filter</li><li>Preparation of BaTi<sub>4</sub>O<sub>9</sub> - BaPr<sub>2</sub>Ti<sub>4</sub>O<sub>12</sub> Composite Powders via Ethylenediaminetetraacetic Acid Precursor</li><li>The Influence of La<sub>2</sub>O<sub>3</sub> Additive on the Dielectric Properties of Ba<sub>0.6</sub>Sr<sub>0.4</sub>TiO<sub>3</sub>-MgO Bulk Ceramics</li><li>Preparation of BaSm<sub>2</sub>Ti<sub>4</sub>O<sub>12</sub> Microwave Dielectric Ceramics via a Polyacrylamide Precursor</li><li>Phase Development and Microwave Dielectric Properties of Ba<sub>4</sub>(Sm<sub>1?y</sub>Nd<sub>y</sub>)<sub>9.33</sub>Ti<sub>18</sub>O<sub>54</sub></li><li>Fabrication of Ba<sub>6-3x</sub>(Sm<sub>0.2</sub>Nd<sub>0.8</sub>)<sub>8+2x</sub>Ti<sub>18</sub>O<sub>54</sub>(x=2/3) Ceramics by Solid State Reaction</li><li>The Microwave Characteristics of Glass-Ba<sub>2</sub>Ti<sub>9</sub>O<sub>20</sub> Ceramics</li><li>Effects of Ta<sup>5+</sup> Substitution on Structure Transition and Microwave Dielectric Properties of Zn(Nb<sub>1-x</sub>Ta<sub>x</sub>)<sub>2</sub>O<sub>6</sub> Ceramics</li><li>Influence of Hydrothermal Conditions on ZST Powders for Microwave Ceramics</li><li>Dielectric Properties of Ba(Mg<sub>0.2/3</sub>Zn<sub>0.8/3</sub>Nb<sub>2/3</sub>)O<sub>3</sub> and Ba<sub>1-x</sub>Sr<sub>x</sub>(Mg<sub>0.2/3</sub>Zn<sub>0.8/3</sub>Nb<sub>2/3</sub>)O<sub>3</sub> Microwave Ceramics</li><li>Effects of CeO<sub>2</sub> Additive on Property of Ba<sub>0.6</sub>Sr<sub>0.4</sub>TiO<sub>3</sub>-MgO Ceramics for Phase Shifter</li><li>Effects of CuO and V<sub>2</sub>O<sub>5</sub> Addition on Sintering Behavior and Microwave Dielectric Properties of (1-x)Ca<sub>2</sub>P<sub>2</sub>O<sub>7-x</sub>TiO<sub>2</sub></li><li>Structure and Dielectric Properties of Zn Doped PST Thin Films Prepared by Sol-Gel Method</li><li>Microwave Dielectric Properties of (1-x)(Ca<sub>0.61</sub>Nd<sub>0.26</sub>)TiO<sub>3</sub>-x(Li<sub>0.5</sub>Sm<sub>0.5</sub>)TiO<sub>3</sub></li><li>Temperature Compensated (1-x)(Na<sub>0.5</sub>La<sub>0.5</sub>)TiO<sub>3</sub>+xCeO<sub>2</sub> Microwave Dielectric Ceramics Incorporated with Copper Oxide</li><li>Preparation and Microwave Dielectric Properties of (1-x)Ca<sub>2/5</sub>Sm<sub>2/5</sub>TiO<sub>3</sub> -x Li<sub>1/2</sub>Nd<sub>1/2</sub>TiO<sub>3</sub> Ceramics</li><li>Effect of ZnO-V<sub>2</sub>O<sub>5</sub> Co-Doping on Phase Stability and Microwave Dielectric Properties of ZnTiO<sub>3</sub> Ceramics</li><li>Effect of V<sub>2</sub>O<sub>5</sub> Addition on the Microwave Dielectric Properties of Ba(Mg<sub>1/3</sub>Nb<sub>2/3</sub>)O<sub>3</sub> Ceramics</li><li>Structure and Dielectric Properties of Citrate Sol-Gel Derived Microwave Ceramics in CaO-ZnO-TiO<sub>2</sub> System</li><li>Microwave Dielectric Property of Porous Silicon Nitride Ceramics</li><li>Preparation and Microwave Permittivity of SiC-AlN Solid Solution Powders</li><li>Properties of Silicon Nitride Using Cordierite as Sintering Additives</li><li>Research on Sintering Dynamics and Microwave Dielectric Properties of Bi and Mn Doped Lead-Based Ceramics</li><li>A Piezoelectric Actuator for Transporting Living Cells</li><li>Organic-Inorganic Nanocomposite Electrodes for Dielectric Elastomer Actuator</li><li>Electro-Mechanical Coupling Performances of a Piezoelectric Bimorph</li><li>Mechanical Properties of Piezoelectric Stack Actuators under Electro-Mechanical Loading</li><li>Analysis of Dynamic Response for Piezoelectric Vibration Converter by Finite Element Simulation</li><li>A Novel Cylinder Driving Ultrasonic Motor</li><li>Actuative Properties of CP Actuator Consisting of Polypyrrole Film and Solid Polymer Electrolyte</li><li>Resonant Modes of Piezoelectric Disc Structure and their Application in Micro Ultrasonic Motors</li><li>Dynamic Properties of Fine-Scale 1-3 PZT/Epoxy Piezoelectric Composites</li><li>A-Site Cational Size Disorder Effects in La<sub>0.55</sub>Ca<sub>0.45</sub>MnO<sub>3</sub></li><li>Electric Fatigue of PZT Piezoelectric Ceramics under Bias and Unipolar Pulse Cycling Field</li><li>Bipolar Electric Fatigue in Ferroelectric Nb-Doped PZST Ceramics</li><li>Propagation and Deflection of Electric-Field-Induced Microcracks in 0.69Pb(Mg<sub>1/3</sub>Nb<sub>2/3</sub>)O<sub>3</sub>-0.31PbTiO<sub>3</sub> Ferroelectric Single Crystals</li><li>Degradation of Lead Zirconate Titanate Piezoelectric Ceramics Induced by Water and AC Voltages</li><li>Degradation Aging of BaTiO<sub>3</sub> Microwave Ceramic Capacitors for EMI Applications at High-Voltage</li><li>The Interfacial Characteristics of Ba<sub>0.6</sub>Sr<sub>0.4</sub>TiO<sub>3</sub> Films Deposited by Radio Frequency Magnetron Sputtering</li><li>Dielectric and Magnetic Properties of BaTiO<sub>3</sub>/NiFe<sub>2</sub>O<sub>4</sub> Composites</li><li>Dielectric Properties of Pb(Zr,Ti)O<sub>3</sub> Heterolayered Thick Films Fabricated by Screen-Printing Method</li><li>Fabrication and Electrical Conductivity of a YSZ-NiCr Cermet</li><li>Preparation and SEM of Ni/Ce-YSZ Anode Materials</li><li>Proton Conductivity of Amorphous Hydrated Zirconia-Yttria Solid Solutions</li><li>Synthesis and Characterization of (Gd, Y)-Doped Ceria Electrolytes for Solid Oxide Fuel Cell</li><li>Preparation and Properties of Ce<sub>0.9</sub>Sm<sub>0.1</sub>O<sub>1.95</sub> as the Electrolytes of IT-SOFC</li><li>Nitrate-Citrate Combustion Synthesis and Properties of Ce<sub>1-x</sub>Gd<sub>x</sub>O<sub>2-x/2</sub> Solid Solutions</li><li>Structural and Morphological Transformation of NaX Zeolite Crystals at High Temperature</li><li>A Study on SrCe<sub>0.9</sub>Y<sub>0.1</sub>O<sub>3-?</sub> Synthesized by Solid State Reaction and the Liquid Citrate Method</li><li>High Performance Low Temperature Ceramic Fuel Cell with Zinc Doped Ceria-Carbonates Composite Electrolyte</li><li>Limiting Current Oxygen Sensors with LSF as Dense Diffusion Barrier</li><li>Structure and Ionic Conductivity of Ln<sub>2</sub>Zr<sub>2</sub>O<sub>7</sub>-Type Rare Earth Zirconates</li><li>Electrical Conductivity of Mixed Conductors (YO<sub>1.5</sub>)<sub>x</sub>-(CeO<sub>2</sub>)<sub>y</sub>-(ZrO<sub>2</sub>)<sub>1-x-y</sub></li><li>Novel Catalytic Electrodes for High Performance Solid Oxide Fuel Cells Operated at Intermediate Temperatures</li><li>Fabrication of YSZ/Ni Composites by Gelcasting</li><li>Microstructure and Electrical Conductivity of Ni-YSZ Cermets Prepared by Combustion Synthesis Method</li><li>NiO-SDC Powder for Solid Oxide Fuel Cell Anode Applications by Buffer Solution Method</li><li>Preparation and Characterization of Sm<sub>1-x</sub>Sr<sub>x</sub>CoO<sub>3</sub> Ceramics by the Gelcasting Process</li><li>Preparation and Electrical Properties of Interconnect Material Made by Substituting Mixed Rare Earth Oxides (Sm<sub>2</sub>O<sub>3</sub>, Gd<sub>2</sub>O<sub>3</sub>, Eu<sub>2</sub>O<sub>3</sub> and CeO<sub>2</sub>) for La<sub>2</sub>O<sub>3</sub> in La</li><li>On the Sealing Materials for SOFC</li><li>Investigation on Structure and Electrochemical Properties of Li[Ni<sub>1/3</sub>Co<sub>1/3</sub>Mn<sub>1/3</sub>]O<sub>2</sub> for Lithium Ion Batteries</li><li>Electrochemical Performance of Al<sub>2</sub>O<sub>3</sub>-Coated LiNi<sub>1/3</sub>Co<sub>1/3</sub>Mn<sub>1/3</sub>O<sub>2</sub> Cathode Materials for Li-Ion Batteries</li><li>Synthesis and Electrochemical Properties of a LiNi<sub>0.7</sub>Co<sub>0.3</sub>O<sub>1.9</sub>Cl<sub>0.1</sub> Cathode Material for Lithium-Ion Battery</li><li>Improvement of the Electrochemical Performance of LiFePO<sub>4</sub> Cathode Composite Material Using a In Situ Pyrolysis Carbon Synthesis Procedure</li><li>Preparation and Electrochemical Characterization of Mn/Pb Composite Oxides for Supercapacitors</li><li>Design and Preparation of Nano-Electrodes for Dye-Sensitized Solar Cell</li><li>Preparation of Spherical Spinel LiMn<sub>2</sub>O<sub>4</sub> Cathode Material for Lithium Ion Batteries</li><li>Ultra Stable Sealing Glass for Intermediate Temperature Solid Oxide Fuel Cells</li><li>Preparation of SDC Interlayer and Influence on Performances of Anode Supported Solid Oxide Fuel Cells</li><li>Fuel Cell Studies Using the CeO<sub>2</sub>-La<sub>2</sub>O<sub>3</sub> Based Electrolytes</li><li>Novel AC-MO-CSC Anode for Direct Methanol Low Temperature Ceramic Fuel Cells </li><li>Manufacturing Processes of Solid Oxide Fuel Cell Components</li><li>Electrochemical Performance of AA Size MCMB/LiCoO<sub>2</sub> Lithium-Ion Battery Using Three-Electrode Cell</li><li>LiNiO<sub>2</sub> Thin Films Fabricated by Diffusion of Li on Ni Tapes</li><li>Improvement of Electrochemical Properties of LiFePO<sub>4</sub>/Carbon Composite Doped by Al<sup>3+</sup> Ions</li><li>Spinel Li<sub>4</sub>Ti<sub>5</sub>O<sub>12</sub>/C Composites as Potential Anode Materials of Lithium Batteries</li><li>Al<sub>2</sub>O<sub>3</sub> Coating of Spherical LiNi<sub>0.8</sub>Co<sub>0.2</sub>O<sub>2</sub> for Li-Ion Batteries</li><li>Fine Lithium Iron(II) Phospho-Olivine Prepared by Different Methods</li><li>Fine-Particle Lithium Iron Phosho-Olivine Synthesized by a Novel Modified Solid-State Reaction</li><li>The Effect of Silicate Layers on Electrochemical Properties in Nanocomposite Solid Polymer Electrolytes</li><li>Low Temperature Electrolyte for Li-Ion Batteries</li><li>Poly(Acrylonitrile-Methyl Methacrylate) Based Microporous Gel Electrolyte for Li-Ion Battery</li><li>Novel-SiO<sub>2</sub>-Doped Proton Exchange Membrane for Self-Humidifying Fuel Cell</li><li>Nano Sulfur Composite for Li/S Polymer Secondary Batteries</li><li>Optical Property of Spark Plasma Sintered Translucent AlN Ceramics</li><li>Modification of Optical Waveguide Material PMMA with Nano-Silicon by Sol-Gel Approach</li><li>Synthesis and Second-Order Optical Nonlinearity of Inorganic-Organic Hybrid Films Bearing Y-Type NLO Active Chromophore</li><li>Optical Properties of Nanocrystalline Ag Doped Silica Inverse Opals</li><li>Large Nonlinear Optical Property of SrBi<sub>2</sub>Nb<sub>2</sub>O<sub>9</sub> Thin Films Prepared by RF Magnetron Sputtering</li><li>Up-Conversion Luminescence in Thulium Doped Barium Titanate Inverted Opal</li><li>Dependence of Electrical and Optical Properties of the Al Doped ZnO for Transparent Conductors Deposited by rf-Magnetron Sputtering on the O<sub>2</sub>/Ar Gas Flow Ratio</li><li>Crystallinity and Photoluminescence Properties of ZnO Films on Zn Buffer Layers Deposited by rf Magnetron Sputtering</li><li>Fabrication, Properties and Theoretical Simulation of Multi-Layer Ceramic Structure Meta-Materials</li><li>Influence of Coumarin Dyes on the Laser Performance of Pyrromethene and Perylene Dyes Co-Doped into ORMOSILs</li><li>Growth and Characterization of Zinc Oxide Films by Pulsed Laser Deposition for Ultraviolet Detection</li><li>Enhancement of the Quality of the ZnO Thin Films by Optimizing the Process Parameters of High-Temperature RF Magnetron Sputtering</li><li>Preparation and Characterization of ZnO Thin Film Doped with Eu via Sol-Gel Method</li><li>Zinc Oxide Thin Films with Reduced Native Compensative Defects Grown by Ultrasonic Spray Pyrolysis at Atmosphere</li><li>Synthesis and Characterization of Y<sub>2</sub>O<sub>3</sub>:Eu<sup>3+</sup> Film Derived by Sol-Gel Processing</li><li>Luminescence Properties of MO-Re<sub>2</sub>O<sub>3</sub>-B<sub>2</sub>O<sub>3</sub>:Eu<sup>3+ </sup>(M= Mg, Sr; Re=Y, Gd ) under VUV Excitation</li><li>Preparation and Properties of Ti, Eu Co-Doped Y<sub>2</sub>O<sub>2</sub>S:0.06Ti,0.08Eu Phosphor with Red Long Afterglow</li><li>Luminescence Reducing Mechanism of Cd Doped Y<sub>2</sub>O<sub>2</sub>S:Ti,Cd Long Afterglow Phosphor</li><li>Modification of Ce-Doped YAG Phosphor with Flux and Ion Substitution</li><li>Synthesis of Green-Emitting Phosphor Y<sub>3</sub>Al<sub>5</sub>O<sub>12</sub>: Tb, Ce, Gd by Sol-Gel Method</li><li>Study on the Synthesis of Long Afterglow Nano-Phosphors SrAl<sub>2</sub>O<sub>4</sub>:Eu,Dy by Microemulsion Method</li><li>Preparation of a New Red Long Afterglow Phosphor Strontium Aluminate Composition</li><li>Luminescence Properties of Spherical Phosphors SrSiO<sub>3</sub>:Eu<sup>3+</sup></li><li>Luminescence Properties of M<sub>2</sub>MgSi<sub>2</sub>O<sub>7</sub>: Re (M = Ba, Sr, Ca) (Re = Eu<sup>2+</sup>, Ce<sup>3+</sup>, Tb<sup>3+</sup>)</li><li>Luminescent Properties of Sr<sub>2</sub>B<sub>5</sub>O<sub>9</sub>Cl Phosphor Doped with Eu</li><li>Synthesis and Luminescent Properties of Ce<sup>3+</sup>-Activated SrGa<sub>2</sub>O<sub>4</sub> and Sr(Ga-Al)<sub>2</sub>O<sub>4</sub></li><li>Microstructural and Micromorphological Studies on ZnSe Single Crystals Using AFM/FE-SEM/RO-XRD</li><li>Ga<sub>2</sub>O<sub>3</sub> Films Grown on Sapphire by the Thermal Evaporation of GaN Powders</li><li>Synthesis of Ultrafine Lu<sub>2</sub>Hf<sub>2</sub>O<sub>7</sub>/Tb Phosphor by Solution Combustion Process</li><li>White Anodic Coatings on Aluminum Alloy with Low Ratio of Solar Absorptance to Infrared Emittance</li><li>Near-Infrared Luminescence and Energy Transfer Characteristics of Dy<sup>3+</sup>-Tm<sup>3+</sup> Co-Doped Selenide Glasses</li><li>Effects of Glass Frits on the Properties of Luminescent Ceramics</li><li>Strong Near-Infrared Luminescence from NiSi<sub>2</sub>-Passivated Silicon Nanocrystals Embedded in SiO<sub>x</sub> Films</li><li>Annealing Environment Effect on the Nanocrystalline Silicon Related Photoluminescence in Silicon Rich Alumina Films</li><li>On the Multilayered Chip-Type PTC Elements Prepared by Roll-Forming Process</li><li>Liquid Desiccant Drying Method for Gelcasting PTC Ceramics Based on BaTiO<sub>3</sub></li><li>Microwave Synthesis of BaTiO<sub>3</sub> from BaCO<sub>3</sub> and TiO<sub>2</sub></li><li>Relations between the Morphology of ZnO Powders and the Electrical Performance of ZnO Varistors</li><li>Equivalent Model of Modified Bismuth Oxides Described by Fractional Derivatives</li><li>Microstructure and Electrical Properties of ZnO-Pr<sub>6</sub>O<sub>11</sub>-Dy<sub>2</sub>O<sub>3</sub>-Based Varistor Ceramics Doped with La<sub>2</sub>O<sub>3</sub></li><li>Preparation and Acetone Sensitive Characteristics of Pure and Cu<sup>2+</sup>-Doped LaFeO<sub>3</sub> Semiconductor Thin Films</li><li>Synthesis of La-Mn Substituted M-Type Ba Hexaferrites by Sol-Gel Method</li><li>Ferromagnetic Properties of Ni<sub>0.2</sub>Cu<sub>0.2</sub>Zn<sub>0.6</sub>Fe<sub>2</sub>O<sub>4</sub>-PZT Composites</li><li>A New Low-Temperature Sintering Method for NiCuZn Ferrite</li><li>An Investigation on the Optimum Conditions for Preparation of Pure Mn-Mg-Zn Ferrite Powder</li><li>Optimization of the Effective Parameters on the Synthesis of the Mn-Zn Ferrite Powder with a High Saturation Magnetization Using Different Iranian Routs of Iron Oxide</li><li>Effect of Phase Formation on Magnetism of Sol-Gel Derived PbTiO<sub>3</sub>/(Ni, Pb) Ferrite Composite Powders</li><li>Complex Impedance Spectroscopy of Bi-Substituted Yttrium Iron Garnet (YIG)</li><li>Application of Rare Earth Permanent Magnet on Magnetic Abrasive Machining</li><li>Growth and Characterization of BaZrO<sub>3</sub> Buffer Layer for Textured YBCO Thin Films Growth on MgO (00l) Substrate</li><li>The Stability Range of Lead Oxide Compounds in Bi-System High Temperature Superconducting Materials</li><li>Synthesis of MgB<sub>2</sub> from Anhydrous B<sub>2</sub>O<sub>3</sub> by Ball Milling Method and Determination of Superconductivity Properties</li><li>CeO<sub>2</sub> Buffer with (200) Preferential Orientation on R-Cut Sapphire by a Solution Deposition Technique</li><li>Preparation of BaRuO<sub>3</sub> and BaIrO<sub>3</sub> Films by Laser Ablation</li><li>Effects of Different Antimony Dopants on ZnO-V<sub>2</sub>O<sub>5</sub> Based Varistor Ceramics</li><li>Fabrication of High Performance Multilayer ZnO Varistors with Chemically Synthesized Doped Zinc Oxide Powder</li><li>Effect of V<sub>2</sub>O<sub>5</sub> Additive on the Microstructure and Electrical Properties of Mn-Co-NiO NTC Thermistor</li><li>Modification of Thick-Film Conductors Used in IP Technology for Reduction of Warpage during Co-Firing of LTCC (Low Temperature Co-Fired Ceramic) Modules</li><li>Morphologies and Microstructures of Antimony-Doped Tin Oxide Films Derived by Sol-Gel Dip-Coating Processing</li><li>The Optical and Electrical Properties of Antimony-Doped Tin Oxide Transparent Conducting Thin Films Prepared by Sol-Gel Dip-Coating Technique</li><li>Improved Electrodeposition of CuIn<sub>1-x</sub>Ga<sub>x</sub>Se<sub>2</sub> Films</li><li>Study of In<sub>2</sub>O<sub>3</sub> Thin Films Prepared on TiN Substrates Using a Triethylindium and Oxygen Mixture</li><li>Resistivity-Temperature Properties of La(Ti<sub>x</sub>Mn<sub>1-x</sub>)O<sub>3</sub> Ceramics</li><li>Control of Shrinkage Behavior and Thermal Expansion Coefficient in BaTiO<sub>3</sub>-Added Ni Electrodes</li><li>Fabrication of Heater Element in Release System</li><li>A Novel Ceramic Pressure Sensor</li><li>Effect of Treatment Process on the Structure and Properties of Sr<sub>0.48</sub>Ba<sub>0.24</sub>Ca<sub>0.28</sub>TiO<sub>3</sub>-Based Varistor Ceramics</li><li>Microstructure and Properties of Ni<sub>0.5</sub>Zn<sub>0.5</sub>Fe<sub>2</sub>O<sub>4</sub>-BaTiO<sub>3</sub> Ceramic</li><li>Dielectric Properties of LTCC System of Al<sub>2</sub>O<sub>3</sub> and Borosilicate Glass</li><li>Fabrication of BN-AlN-TiB<sub>2</sub> Compound Conductive Ceramics by Self-Propagating High Temperature Synthesis and Hot Isostatic Pressing</li><li>Effect of Raw Materials on the Thermal Conductivity and Microstructure of Aluminum Nitride</li><li>SrTiO<sub>3</sub> Based Dual-Functional Ceramics with Nano-Additives</li><li>Dielectric Properties of Boron Nitride-Aluminium Nitride Composites Prepared by Spark Plasma Sintering</li><li>Preparation and Properties of Ni-Si-O Thin Film Prepared by Sol-Gel Method</li><li>Na-Site Doping of NaCo<sub>2</sub>O<sub>4</sub> Thermoelectric Materials</li><li>Preparation and High Temperature Thermoelectric Properties of [Ca<sub>2</sub>(Co<sub>0.65</sub>Cu<sub>0.35</sub>)<sub>2</sub>O<sub>4</sub>]<sub>0.624</sub>CoO<sub>2</sub> Compound</li><li>Large Thermoelectric Response of Ti-Containing Perovskite Oxides</li><li>Progress in Researches on the Layered Cobalt Oxides for Thermoelectric Devices</li><li>Modulated Structure of Bi<sub>1.8</sub>Sr<sub>2.0</sub>Rh<sub>1.6</sub>O<sub>x</sub></li><li>Preparation and Properties of Zinc Oxide and Titanium Oxide Ultra-Fine Composite Particles for Attenuation of Ultraviolet Radiation</li><li>Static and Dynamic Characteristics of Thermoelectric Ceramics</li><li>Synthesis and Thermal Properties of Nanoscale Skutterudite via Cross-Coprecipitation</li><li>Microstructure and Thermoelectric Properties of CoSb<sub>3</sub> Synthesized by MA-SPS Method</li><li>Synthesis and Lattice Thermal Conductivity of Double Atoms Filling p-Type Ca<sub>m</sub>Ce<sub>n</sub>Fe<sub>x</sub>Co<sub>4-x</sub>Sb<sub>12</sub> Compounds</li><li>High Temperature Thermoelectric Property of Sr-Filled Skutterudite Sr<sub>y</sub>Co<sub>4</sub>Sb<sub>12</sub></li><li>Influence of Extrusion Temperature on the Thermoelectric Properties of p-Type Ag Added (Bi<sub>0.25</sub>Sb<sub>0.75</sub>)<sub>2</sub>Te<sub>3</sub> Alloys Prepared by MA-PDS</li><li>Preparation of Ag<sub>x</sub>Pb<sub>m</sub>SbTe<sub>2+m</sub>-Based Thermoelectric Materials by MA-SPS Method and Evaluation of their Thermoelectric Properties</li><li>Thermoelectric Properties of Ag<sub>1-x</sub>Pb<sub>m</sub>SbTe<sub>2+m</sub> Compounds</li><li>High Temperature Thermoelectric Properties of AgPb<sub>18+x</sub>SbTe<sub>20</sub></li><li>Annealing Effects on Powder Metallurgy Based Pb<sub>1-x</sub>Sn<sub>x</sub>Te Materials for Thermoelectric Applications</li><li>Thermoelectric Properties of Bismuth Telluride Based Materials Prepared by Powder Metallurgy Processing</li><li>Electrical Properties of P-Type Thermoelectric Ag<sub>x</sub>Bi<sub>0.5</sub>Sb<sub>1.5-x</sub>Te<sub>3</sub> (x=0.05~0.4) Alloys Prepared by Spark Plasma Sintering</li><li>Template Synthesis of Bismuth Porous Films and Networked X-Shape Nanowires</li><li>The Influence of Oxygen on the Electrical Properties of Bulk and Thin Films of PbTe Semiconductors</li><li>Structural Evolution of Nb/NbC Multilayer Coatings</li><li>Heat to Electricity Conversion Efficiency Measurement for Thermoelectric Unicouple</li><li>High-Efficiency Thermoelectric Air-Conditioner</li><li>Novel High-Intensity Thermoelectric Generator and its Application on Hybrid Electric Vehicle</li><li>Preparation and Characterization of Sr, Ba Filled Type-I Ge Clathrate Single Crystals</li><li>Thermoelectric Properties and Mechanism on Porous Silicon Wafer</li><li>Structural and Optical Ceramics: Yesterday, Today, and Tomorrow</li><li>On the Progress of Combustion Synthesis of Si<sub>3</sub>N<sub>4</sub> Ceramic: From Laboratory Research to Industrial Production</li><li>Fabrication and Characteristics of Al2O3/Cu Composite Particles by MA & PCS</li><li>Preparation of Submicron Silica Powders from Sodium Silicate Using Ultrasonic Energy</li><li>Preparation of Mullite Powder by Aluminum Sulfate and Silica in Molten Sodium Sulfate</li><li>Preparation of Ultrafine ?-Sialon Powder by Citrate Sol-Gel and Carbothermal Reduction Nitridation</li><li>Preparation of (Ca+M) (M=Mg, Yb, Sr) Co-Doped ?-SiAlON Powders by Combustion Synthesis</li><li>Preparation of Sialon Using Fly Ash with High Content of Al<sub>2</sub>O<sub>3</sub></li><li>Combustion Synthesis of Magnesium Silicon Nitride Powders in the Mg-Si-N System</li><li>SiC Platelets Synthesized by Powder-Heating Technique</li><li>Synthesis of Sialon-Mullite Composites Using Fly Ash by Carbon-Thermal Reduction Nitridation</li><li>Carbothermal Preparation of Ultra-Fine TiB<sub>2</sub> Powders Using Solution-Derived Precursors via Sol-Gel Method</li><li>Large-Scale Fabrication of Ti<sub>3</sub>AlC<sub>2</sub> Powder with High-Purity</li><li>Study of Ti<sub>3</sub>Si<sub>1.2-x</sub>Al<sub>x</sub>C<sub>2</sub> (x = 0~1.2) Solid Solution via X-Ray Diffraction</li><li>Mechanically Activated Low-Temperature Synthesis of Ti<sub>2</sub>SnC</li><li>Fabrication and Mechanical Properties of High-Pure Ti<sub>3</sub>SiC<sub>2</sub> Bulk Materials Directly by Hot-Pressing its Powder</li><li>Surface Coating of Anhydrite Powders with CaCO<sub>3</sub> Nano-Particles Prepared in Ca(OH)<sub>2</sub>-H<sub>2</sub>O-CO<sub>2</sub> System</li><li>Tribochemical Effects of MoSi<sub>2</sub> Powder in Ball Milling</li><li>Preparation and Characterization of Ca<sub>0.8</sub>Sr<sub>0.2</sub>ZrO<sub>3</sub> Powders Prepared by Soft Chemical Route</li><li>Synthesis of Mixed Conducting Oxides SrFeCo<sub>0.5</sub>O<sub>y</sub> Powder by Citrate Method</li><li>A New Homogeneous Precipitation Route to Ammonium Aluminum Carbonate Hydroxide</li><li>A Novel 3D Patterning Technique for Forming Advanced Ceramics</li><li>Application of Acetate Starch to Colloidal In Situ Consolidation Molding Process of Alumina Ceramic</li><li>Rheological Behavior of Alumina Aqueous Suspension for Extrusion Gelation Freeform Fabrication</li><li>Rheological Properties of Boron Nitride-Silica Composite Suspensions</li><li>Effect of Various Dispersants on the Gel-Casting of Silicon Nitride</li><li>Effect of SiC Powder Characteristic on the Rheological Properties of Feedstock</li><li>Simulation of Ceramic Injection Molding for Zirconia Optical Ferrule</li><li>Superplastic Deformation of Nano-Sized ?-Sialon Ceramics</li><li>Forming of Large Thin Walled Fused Silica Shapes by Gelcasting</li><li>Study on Processing Parameters of Ceramic Injection Moulding</li><li>A New Dewaxing Method and its Effect on the Properties of Low-Pressure Injection Molded Ceramics</li><li>Injection Molding of Zirconia Ceramics Using Water-Soluble Binder</li><li>The Influences of Solid Loading and Molding Variables on Alumina Injection Molding</li><li>On the Defects in Injection-Moulded Technical Ceramics</li><li>Effects of Different Debinding Atmosphere on the Properties of Powder Injection Molded AlN Ceramics</li><li>Near-Net Shaping of Microwave Ceramics by Gel-Casting with Carrageenan</li><li>Extrusion Forming of Cordierite Honeycomb with Hexagonal Open Cells</li><li>Preparation of PZT Slurry with High Solids Loading and Low Viscosity for Gelcasting</li><li>Magnetic Alignments of Ba-Ferrite Particles in Suspension</li><li>Synthesis of Fine Grain Ti<sub>3</sub>SiC<sub>2</sub> by Spark Plasma Sintering with Additive of Aluminum</li><li>Fabrication of TiAl Intermetallic by Spark Plasma Sintering</li><li>Spark Plasma Sintering of CBN-WC-10Co Composites</li><li>Preparation of Porous Alumina Ceramics by Spark Plasma Sintering</li><li>Comparison of Spark Plasma Sintering and Hot Pressing of MgAlON</li><li>Liquid Phase Sintering of ?-Si<sub>3</sub>N<sub>4</sub> by Spark Plasma Sintering</li><li>Effect of Aluminum on Fabrication of Ti<sub>3</sub>SiC<sub>2</sub> by Mechanical Alloying and Spark Plasma Sintering</li><li>Liquid Phase Sintering Behavior of Amorphous Nano-Sized Silicon Nitride Powders</li><li>Microwave Sintering of Alumina-Silicon Carbide Nanocomposites</li><li>Fabrication and Characterization of Porous TiB<sub>2</sub> Ceramic with Three-Dimensional Interconnected Skeleton</li><li>Synthesis of a Novel B<sub>3</sub>CN<sub>3</sub> Compound by Pyrolysis of Precursor</li><li>The Effect of Diluent on Combustion Synthesis of Si<sub>3</sub>N<sub>4</sub>-SiC-TiN Ceramics with Small Diameter</li><li>Preparation of Porous Si<sub>3</sub>N<sub>4</sub> Based Ceramics by Combustion Synthesis</li><li>Low Temperature Fabrication and Characterization of Porous SiC Ceramics Using Polycarbosilane as Binder</li><li>Processing and Characterization of Carbothermal Reduction and Nitridation from Kaolinite-Polyacrylamide Intercalation Compound</li><li>Fabrication of Reticulated Porous Ceramics with Controlled Structure by Centrifuging Process</li><li>Preparation of Porous Ceramic Support with Inorganic Filtration Membrane</li><li>Preparation of Porous Wollastonite Ceramics for Filtration</li><li>Fabrication of Porous Silicon Nitride with High Porosity</li><li>Properties and Application of Oriented Porous SiC as Transpiration Cooling Materials</li><li>Fabrication of Porous Cellular SiC Ceramics from Wood by Embedding in Si/SiO<sub>2</sub> Powder Mixture</li><li>Study of Affecting Factors on Porosity in Gel-Casting Foam</li><li>Preparation and Characterization of ZrO<sub>2</sub> Microspheres by Internal Gelation Process</li><li>Preparation and Microstructure of Bauxite Ceramic Microsphere</li><li>Homogeneity of Aqueous Al<sub>2</sub>O<sub>3</sub>/3Y-TZP Feedstock by Plastic Kneading</li><li>Effects of Adding Form of Additives on the Structure and Properties of High-Purity Alumina Ceramics</li><li>Preparation and Properties of Al<sub>2</sub>O<sub>3</sub>-Mullite-SiC Nano-Composite by Slip Casting in a High Magnetic Field and Reaction Sintering</li><li>Preparation of Zirconia-Toughened Alumina Ceramics through the Dispersal Basic Carbonate Precursors</li><li>Structural Characterization, Crosslinking and Pyrolysis Investigation of Carbosilane Oligomers</li><li>RB-SiC Ceramics Derived from the Phenol Resin Added with Starch</li><li>TiC/Ti Composite Layers Fabricated by Laser Surface Alloying</li><li>Fabrication of Lightweight SiC Space Mirror</li><li>Advanced Engineering Ceramics for Semiconductor Package Technology</li><li>Ultra-High Temperature Ceramics (UHTCs) via Reactive Sintering</li><li>Effects of Rapid Heat Treatment on Microstructure and Mechanical Properties of Ti<sub>2</sub>AlC/TiAl Composite</li><li>Microstructure and Properties of Carbon-Ceramic Composite Prepared by Hot-Pressing Sintering</li><li>Microstructural Evolution and Mechanical Properties in Yb<sub>2</sub>O<sub>3</sub>-Fluxed Silicon Nitride Ceramics</li><li>Processing and Properties of Highly Textured Si<sub>3</sub>N<sub>4</sub> Materials</li><li>A Comparison Study on Microstructure and Mechanical Properties of Si<sub>3</sub>N<sub>4</sub> Ceramic Prepared from MACS Powders</li><li>Microstructure of Different Rare-Earth-Doped ?-Sialon Ceramics</li><li>The Influence of Sintering Process on the Microstructure of Submicron Alumina Fabricated by Gelcasting</li><li>Low Temperature Degradation of Yttria Stabilized Zirconia</li><li>Effect of Al<sub>2</sub>O<sub>3</sub> on the Phase Stability of Y-Ce-TZP/Al<sub>2</sub>O<sub>3</sub> Composites at Low Temperature</li><li>Microstructure and Phase Composition of (Ce, Mg)-PSZ Ceramics</li><li>Microstructure and Mechanical Properties of Ce-Y-TZP Ceramic Composites for Ceramic Plunger and Ball Valve</li><li>Effect of HIP on the Properties and Microstructure of Transparent Polycrystalline Spinel</li><li>Processing of Zinc-Based MgAl<sub>2</sub>O<sub>4</sub> Composite and Effect of Fly Ash Addition</li><li>A Study on Toughening and Strengthening of Mg-Al Spinel Transparent Ceramics</li><li>Study on the Properties of Alumina Ceramics after Implanted by Titanium Ions with MEVVA Sources</li><li>Microstructures and Mechanical Properties of Nano-Composite Ti(C,N)-Based Cermets</li><li>Preparation of Amorphous Si-B-C-N Powders and Nano-Sized Ceramics</li><li>Synthesis and Properties of Ternary Carbide Ti<sub>3</sub>AlC<sub>2</sub> Ceramics</li><li>Preparation of ZnSe by CVD with the Solid Starting Materials</li><li>Novel Visible-Band Transparent Ceramic Laser Material Mn:MgAl<sub>2</sub>O<sub>4</sub></li><li>Synthesis, Characterization of Perhydropolysilazane and its Application in the Preparation of 3D SiO<sub>2f</sub>/Si <sub>3</sub>N<sub>4</sub> Composites</li><li>Influence of Pressure on the Crystallization in SiO<sub>2f</sub>/SiO<sub>2</sub> Composites</li><li>Ablated Transformation and Dielectric of SiO<sub>2</sub>/SiO<sub>2</sub> Nanocomposites Dipped with Silicon Resin</li><li>Preparation and Property Study of 3D C<sub>f</sub>/Si-Ti-C-O Composites Fabricated with Polytitanocarbosilane by PIP Process</li><li>Mechanical Properties of C/SiC Composites via Precursor Pyrolysis with Pretreated Carbon Fiber</li><li>Microstructure of C<sub>f</sub>/SiC Composite with Precursor of Hexamethyldisilazane by Chemical Vapor Infiltration</li><li>Processing and Properties of 2D C<sub>f</sub>/Si-O-C Composites Using Silicone Resin</li><li>Fabrication and Mechanical Properties of SiC<sub>f</sub>/SiC Composites via Polycarbosilane Pyrolysis</li><li>Fabrication of SiC/SiC Composites Using both Chopped Fiber and a Hybrid Reinforcement of Chopped and Continuous Fibers</li><li>Transient Liquid Phase Bonding of 2D Fiber Reinforced Carbon-Carbon Composites</li><li>Effect of the Formation of SiC Whisker on the Properties of Al<sub>2</sub>O<sub>3</sub>-ZrO<sub>2</sub>-C Materials</li><li>Dielectric and Mechanical Properties of Unidirectional SiC Fiber-Reinforced Aluminum Phosphates Composite</li><li>Microstructure of Pyrolytic Carbon Matrix in Carbon/Carbon Composites after Graphitization</li><li>Tensile Behavior of Aluminum Matrix Composites Reinforced by Aluminum Borate Whiskers and Magnetic Ceramic Particles</li><li>CNTs/Si<sub>3</sub>N<sub>4</sub> Composites Fabricated by Reaction Bonded Processing</li><li>Phase Evolution of Aluminum-Chromium-Phosphate Binders during Heat-Treatment</li><li>Effect of PCS Pyrolysis Process on C Fiber in C<sub>f</sub>/SiC Composite</li><li>Effect of Oxygen on the Mechanical Properties of Polymer-Derived Si-Al-C-O Fibers</li><li>Effect of Heat Treatment on the Microstructure and Mechanical Properties of Cf/SiC Composites</li><li>Silicon Carbide Whiskers Synthesized by Double-Heating Technique</li><li>Composition, Structure and Properties of Low Oxygen Content SiC Fibers</li><li>SAXS Characterization of Nanochannels in Polymer-Derived SiC Fibers</li><li>Effect of Catalyst on the Preparation of Silicon Carbide Whiskers from Silica and Carbon</li><li>Synthesis of the Fiber Coating by FP-CVI Process</li><li>Microstructural Characterization of In Situ TiB Whiskers in Ti MMCs Fabricated by SPS</li><li>Preparation and Morphology of Mullite Whiskers by Sol-Gel Method</li><li>The Preparation of Fibrous MCM-41 Using Microwave Heating</li><li>Influence of Fabricated Process on Mechanical Properties of Porous SiC-Particle/Si<sub>3</sub>N<sub>4</sub> Composites</li><li>Effect of Second Sintering on Intragranular Structure and Mechanical Properties of 10vol%Al<sub>2</sub>O<sub>3</sub>/3Y-TZP Composites</li><li>Synthesis of Aluminum Titanate Solid Solution by Solid State Reaction of Fine Commercial Al<sub>2</sub>O<sub>3</sub>, TiO<sub>2</sub> and MgO Powders</li><li>Preparation of LiTaO<sub>3</sub> Ceramic Powders</li><li>Effect of Aluminium Sol on Microstructure and Properties of Corundum-Mullite Ceramic</li><li>Fabrication of Al<sub>2</sub>O<sub>3</sub>-SiC-Mullite Composites from Fly Ash</li><li>Preparation of TiB<sub>2</sub> Nanoparticles Reinforced Cu-Matrix Composite by Direct Combustion Synthesis</li><li>Preparation of Warm Compacted and Sintered WC/Carbon Steel Composite and its Wear-Resistance</li><li>The Preparation and Properties of Si<sub>3</sub>N<sub>4</sub>-Filled Epoxy Resin Composites for Electronic Packaging</li><li>Preparation and Properties of ?-Si<sub>3</sub>N<sub>4</sub>/Epoxy Matrix Composite</li><li>Manufacturing of Polymer Matrix Composite Material Using Marble Dust and Fly Ash </li><li>Performance Analysis and Experimental Verification for FBG Sensors Applied for Smart Structure</li><li>Multilayer SiC/Si Composites Derived from Papers</li><li>An Investigation of the Reaction Hot-Pressing Synthesis of MoSi<sub>2</sub>/Ti<sub>3</sub>SiC<sub>2</sub>/Al Composites</li><li>Reaction Path and Microstructures of Ti<sub>3</sub>SiC<sub>2</sub>/SiC Composite by Spark Plasma Sintering</li><li>Interformational Exfoliation of Ti<sub>3</sub>Al<sub>2</sub> Induced by Cu</li><li>The Reaction between Ti<sub>3</sub>AlC<sub>2</sub> and Cu in the Synthesis Process of Cu/Ti<sub>3</sub>AlC<sub>2</sub> Composites</li><li>High Performance Composite of Silicon Carbide/ Bismaleimide</li><li>In Situ Formation of TiC Reinforced Intermetallic-Matrix Composite Layers Produced by Laser Cladding</li><li>Effect of Ti<sub>3</sub>SiC<sub>2</sub> Content on Mechanical Properties of Ti<sub>5</sub>Si<sub>3</sub>-TiC-Ti<sub>3</sub>SiC<sub>2</sub> Composites</li><li>Slip Casting of Green Compact of SiAlON Multiphase Ceramics from River Sand</li><li>Steel-Bonded Cemented Carbide GT35 by In Situ Reduction of Natural Ilmenite</li><li>Unusual Microstructures and Strength Characteristics of Cu/Ti<sub>3</sub>AlC<sub>2</sub> Cermets</li><li>Reaction Synthesis of TiAl-Al<sub>2</sub>O<sub>3</sub> Composite</li><li>Synthesis and Structure of Sol-Gel Derived PST/Bi<sub>2</sub>Ti<sub>2</sub>O<sub>7</sub> Composite Thin Films</li><li>Preparation and Characterization of Copper-Coated Alumina Powders</li><li>Manufacture and Microstructures of Fe-Cr-C Hypereutectic In Situ Composites</li><li>Microstructure and Mechanical Properties of Heat-Resistant Silicon Carbide Ceramics</li><li>Defect and its Influence on Mechanical Property of Titanium Diboride-Copper Matrix Composite</li><li>Mechanical Properties of Al<sub>2</sub>TiO<sub>5</sub> Ceramics</li><li>High Temperature Creep Strength of Si<sub>3</sub>N<sub>4</sub>-Y<sub>2</sub>Si<sub>2</sub>O<sub>7</sub> Ceramics by Stress Relaxation Based on a New Interpretation Model</li><li>Mechanical Properties and Microstructure of Al<sub>2</sub>O<sub>3</sub>-TiC Composite by Hot-Pressing</li><li>Preparation and Properties of BN-SiO<sub>2</sub> Composite Ceramics</li><li>Spark Plasma Sintered ZrO<sub>2</sub>(Y<sub>2</sub>O<sub>3</sub>)-Al<sub>2</sub>O<sub>3</sub>-SrSO<sub>4</sub> Self-Lubricating Nanocomposites for High Temperature Tribological Applications</li><li>Effect of Y<sub>2</sub>O<sub>3</sub> on Properties of Al/Ti<sub>3</sub>SiC<sub>2</sub> Composite</li><li>A New Ti<sub>3</sub>AlC<sub>2</sub>/Cu Cermet Exhibiting Excellent Tribological Properties</li><li>Effect of Micro-Pores after Sintering on Wear Behavior of Zirconium Silicate Composite Microbeads</li><li>Fabrication of TiC Particles Reinforced Hadfield Steel Matrix Composite and its Wear-Resistance</li><li>Plating Copper on Al<sub>2</sub>O<sub>3</sub> Powder in Ceramal</li><li>A Study on the Grinding Performance of Y-TZP/Al<sub>2</sub>O<sub>3</sub> Ceramics</li><li>Precision Machining of Si<sub>3</sub>N<sub>4</sub> Refrigerator Friction Couple Based on FEA</li><li>Grinding of TZP/Al<sub>2</sub>O<sub>3</sub> Composite with Vitrified CBN Wheels</li><li>High Speed Lapping of SiC Ceramic Material with Fixed Abrasive</li><li>Micro Groove Machining Characteristics of Si<sub>3</sub>N<sub>4</sub>-hBN Composites</li><li>Wear Characteristics of Twist Drills in Machining Fluorophlogopite</li><li>Surface Behaviors of ELID Ground Engineering Ceramics</li><li>In-Process Electrolytic Dressing Lapping (IEDL) of Al<sub>2</sub>O<sub>3</sub>-BN Machinable Ceramics</li><li>Fabrication of SiCN MEMS by UV Lithography of Polysilazane</li><li>Thermodynamic Properties of Gangue</li><li>Properties of Sol-Gel Bonding Castables</li><li>Fabrication and Characterization of Mullite Whisker-Reinforced Porous Refractory</li><li>Colloidal Processing of Alumina-Carbon Ceramic Refractories</li><li>Densification of Unfired Alumina Refractories by the In Situ Spinel Formation during Application</li><li>Preparation and High Temperature Performance of ?-Sialon Bonded Corundum Multiphase Material</li><li>Fabrication of Fe-Al Intermetallic/TiC-Al<sub>2</sub>O<sub>3</sub> Ceramic Composites from Ilmenite by Reaction Sintering</li><li>Preparation of Nanoporous Super Thermal Insulation Material Compounded with Xonotlite-SiO<sub>2</sub>-Aerogel and Characterization of the Pore Structure</li><li>Synthesis and Properties of Silica Aerogel by Using Acid Silica Sol and TEOS as Silicon Sources</li><li>Thermal Shock Resistance and Ablation Behavior of TiB<sub>2</sub>-Cu-Ni Composite via Combustion Synthesis</li><li>A Novel Approach to Prepare Ni-Coated TiB<sub>2</sub> Cermet</li><li>Microstructure and Properties of (Ti,W)(C,N)/(Ni,Mo) Cermets after a Heat-Treatment at High Nitrogen Pressure</li><li>Effect of Cr<sub>2</sub>C<sub>3</sub> Addition on Microstructure and Mechanical Properties of Ti(CN)-Based Cermets</li><li>Residual Stress Field of Ellipsoidal Ceramic Particles Ni-Base Alloy Composite Coating</li><li>FEM Analysis on Thermal Stress of Desulphurization Injection Lance</li><li>Investigation on the Porous Biomaterial for Bone Reconstruction with Addition of Bio-Mimetic Nano-Sized Inorganic Particles</li><li>Inhibitory Effect of Synthetic Nano-Hydroxyapatite on Dental Caries</li><li>Apatite Formation on the Surface of Dense HA/TCP in Animals' Serums</li><li>In Vitro Degradation of ?-TCP/PLLA Scaffolds with Different Proportions of ?-TCP</li><li>Application of Multilayer Collagen/HA Scaffold in Cartilage Tissue Engineering</li><li>AFM Study on the Surface Dissolution of Hydroxyapatite</li><li>Solution Behavior of CaO-MgO-SiO<sub>2</sub> System Bio-Soluble Refractory Ceramic Fibers</li><li>The Interface Reaction between an Ag<sup>+</sup>-Doped TiO<sub>2</sub> Film and Stainless Steel Substrate</li><li>Preparation of Antibacterial Ceramics with Silver-Carrying Nano-Hydroxyapatite</li><li>Effect of Reaction Conditions on Pore Configuration and Mechanical Property for Porous Hydroxyapatite Prepared by Polymer Sponge Method</li><li>Factors Affecting the Pore Size in Porous Hydroxyapatite Produced by Stir-Froth-Polymerization Method</li><li>Biomimetic Fabrication and Characterization of BG/COL/HCA Scaffolds for Bone Tissue Engineering</li><li>FCVA-Synthesized Tetrahedral Amorphous Carbon Films for Biomedical Applications</li><li>A Study on Biomineralization Behavior of Silk Fibroin Film</li><li>MicroCT Aided Scaffold Design and Preparation</li><li>Mechanical Properties of Machinable Zirconia Dental Composites</li><li>Microstructure and Crystallization Behavior of Glasses in the ZrO<sub>2</sub>-ZnO-Al<sub>2</sub>O<sub>3</sub>-SiO<sub>2</sub> System</li><li>Low-Temperature Sintering of 3Y-TZP/Glass Composites as All-Ceramic Dental Materials</li><li>Structure and In Vitro Bioactivity of Si Enriched Hydroxyapatite/TiO<sub>2</sub> Coatings on Pure Titanium by Micro-Arc Oxidation</li><li>Microstructure Analysis of a Composite System Composed of Zirconia/Alumina Composites and Vita Alpha Coating-Glass for Dental Applications</li><li>Effect of Surface Roughness on Matching Properties between Ceramic Framework and Coating-Glass for Dental Applications</li><li>Effect of CNTs on Property of Calcium Phosphate Cement</li><li>Preparation of Unsintering Calcium Phosphate Macroporous Materials with Hydroxyapatite Nanowhisker In Situ Growth</li><li>Porous Hydroxyapatite Bioceramics Prepared by Polymeric Sponge Impregnation Process</li><li>Self-Setting Biphase Porous Calcium Phosphate Cement</li><li>Characterization of Porous Calcium Phosphate Bioceramics Modified by Porosifier</li><li>Effects of Setting Liquid on ?-Calcium Phosphate-Tetracalcium Phosphate Bone Cement</li><li>In Vivo Behavior of Injectable Fast-Setting Calcium Phosphate Cement</li><li>Improvement of Anti-Washout Performance of Calcium Phosphate Cement Using Modified Starch</li><li>Electrochemically Assisted Co-Precipitation of Electrically Conducting Polymer with Calcium Phosphate Coatings on Ti Alloys</li><li>Degradation Behavior of Calcium Sulfate/?-Tricalcium Phosphate Composites in Tris</li><li>Exploring the Osteoinductivity of Calcium Phosphate Ceramics/PLA or Collagen Composites</li><li>Preparation of ?-TCP/HAP Composite Bioceramics</li><li>Preparation and Characterization of Biodegradable ?-TCP-Based Composite Microspheres as Bone Tissue Engineering Scaffolds</li><li>Degradation Behavior of ?-Ca<sub>3</sub> (PO<sub>4</sub>)<sub>2</sub>/?-Ca<sub>2</sub>P<sub>2</sub>O<sub>7</sub> Bioceramics</li><li>Physicochemical and Mechanical Properties of Composite of Chitosan Microspheres/Calcium Phosphate Cement</li><li>Rheological Properties of an Injectable Calcium Phosphate Bone Cement and their Relationship with the Phase Evolution</li><li>Repairing the Dog's Femoral Defect with the Autologous Osteoblast Integrated the Nano-Calcium Phosphate/Zirconia Scaffold</li><li>Bone Formation in Non-Osseous Tissues of Biphasic HA/?-TCP Bioceramics Sintered by Different Ways</li><li>Hydroxyapatite Coatings Deposited on Titanium Substrate by Pulsed Laser Deposition</li><li>Preparation of Bioactive ?-Tricalcium Phosphate Scaffold with Bone-Like Structure</li><li>TEM Analysis on Bio-Functional Gradient Hydroxyapatite/ZrO<sub>2</sub> Coatings</li><li>Improvement of Biocompatibility and Osteointegration of Zirconia Implants by Means of Bioactive Glass Coating: An Experimental Study in Animal</li><li>Bioactive Ceramics - New Processing Technologies for Immobilization of Microorganisms for Filtration and Bioreactor Applications</li><li>Preparation of Biphasic Calcium Phosphate Porous Ceramics Prepared from Fine Powders with Different Particle Size and its Dissolution Behavior in Simulated Body Fluid</li><li>Apatite Forming on the Surface of Apatite-Wollastonite/?-Tricalcium Phosphate Bioactive Ceramic</li><li>Simulation In Vitro of Subsonic Flame Sprayed Titanium/Biological Glass Composite Coating</li><li>Biomimetic Synthesis of PEC-HA Composite Analogous to Bone</li><li>Development of Ultrafine Fibrous Hydroxyapatite/Polymer Scaffold by Electrospinning</li><li>Experimental Study of Biomimetic Mineralization on the Surface of Piezoelectric Pulp-Cap Film</li><li>Bisphosphonate Pamidronate Modifying Hydroxyapatite Bioceramics for Hard Tissue Repair</li><li>Microstructure and In Vitro Bioactivities of HA/Ti Composites Prepared by Hot Isostatic Pressing</li><li>Improvement in the Sensitivity of the Response of Diamond Thin Films to X-Ray</li><li>Microstructure of Ceramic Layer in Composite Pipe Made by SHS-Gravitational Process</li><li>Microstructure and Properties of In Situ Synthesis of TiC Particle Reinforced Composite Coating by Induction Cladding</li><li>Adhesion of Diamond Film to Co- Deficient Cemented Tungsten Carbide Substrate</li><li>Wear Behavior of Plasma Sprayed Ni-WC Composite Coatings</li><li>Microstructure and Dry Sliding Tribological Behavior of Microarc Oxidation Coating Formed on Ti6Al4V against Steel</li><li>Preparation of DLC Scratch-Resistant Coating on PC Glass Lenses</li><li>Micro-Tribological Behavior of Boron Carbide Self-Mated Pairs</li><li>Frictional Performance of Brake Pads against Al Metal Matrix Composites with Different Sizes of SiC Particles</li><li>Effects of Pre-Oxide Layer Thickness on Thermal Cyclic Behavior of Thermal Barrier Coatings</li><li>Cyclic Oxidation Behavior of Thermal Barrier Coatings in Environments Containing Water Vapor</li><li>Design and Properties of Fire-Proof Coating for Tunnels</li><li>Influence of Infiltration Additives on the Phase, Microstructure and Oxidation Resistance of SiC Coating for Graphite Materials</li><li>Thermal Cycling Behavior of Lanthanum-Cerium Oxide Thermal Barrier Coatings Prepared by Air Plasma Spraying</li><li>A Promising Sm<sub>1.9</sub>Ca<sub>0.1</sub>Zr<sub>2</sub>O<sub>6.95</sub> Ceramic for Thermal Barrier Coatings</li><li>Low Thermal Conductivity Ceramics for Thermal Barrier Coatings</li><li>Fabrication and Isothermal Oxidation Behavior of the Co-Deposited EB-PVD (NiAl + YSZ) Coating</li><li>A Comparative Study of Two-Layer NiAl Bond Coat TBC and its Failure Mechanism</li><li>Thermophysical Properties of Samarium-Cerium Oxide for Thermal Barrier Coatings Application</li><li>A Comparison of the Surface Properties of DLC and Nanocrystalline Diamond</li><li>Influence of Impurities on the High-Temperature Water-Vapour Corrosion of Environmental Barrier Rare-Earth Silicates</li><li>Analysis of Heat Transfer and Thermal Stress in Thermal and Environmental Barrier Coatings</li><li>Investigation of YSZ Thin Films on Silicon Wafer and NiO/YSZ Deposited by Ion Beam Sputtering Deposition (IBSD)</li><li>Influence of Agglomerate Size on the Properties of Al<sub>2</sub>O<sub>3</sub>-Al<sub>2</sub>Cu<sub>3</sub> Multiphase Ceramic Coatings</li><li>Effect of Heat Treatment on Coloration of Ag Doped TiO<sub>2</sub>-SiO<sub>2</sub> Films</li><li>Photo-Hydrophilicity and Photo-Catalysis of TiO<sub>2</sub>-SiO<sub>2</sub> Coating on Ceramics</li><li>AFM Investigation of Nano Particle Incorporated Sb Doped SnO<sub>2</sub> Films</li><li>Development and Characterization of Nano-TiO<sub>2</sub>/HA Composite Bioceramic Coating on Titanium Surface</li><li>Interface Biomechanical Properties between Femora and Bioactive Ceramic Coatings Prostheses during the Initial Implant Stage</li><li>Two-Steps Digital Image Correlation and Application to Studies of Micromechanics Behavior of Coating Interface</li><li>Adsorption of Human Serum Proteins on Carbonaceous Materials</li><li>Thermal Shock Experiment and Simulation of Ceramic/Metal Gradient Thermal Barrier Coating</li><li>Mechanisms and Kinetics of Silica-Rich Binary Na<sub>2</sub>O-SiO<sub>2</sub> Glass Corrosion in 100 degreesC Water at pH=7</li><li>Effect of Heat Treatment on the DC Conductivity and Activity Energy of Li<sub>2</sub>O-Fe<sub>2</sub>O<sub>3</sub>-P<sub>2</sub>O<sub>5</sub> Glasses</li><li>Crystallization of a SiO<sub>2</sub>-MgO-Al<sub>2</sub>O<sub>3</sub>-K<sub>2</sub>O-Fe<sub>2</sub>O<sub>3</sub>-F Glass</li><li>Making Fluorophlogopite Ceramics through Ceramic Processing</li><li>Preparation of Decorative Building Glass-Ceramics by Using Cracked-Glass Panel as Precursor</li><li>Sintering and Crystallization of Glass-Ceramics for Optical Fiber Ferrule</li><li>Manufacture Process of Light Calcium Carbonate from Limestone</li><li>Upconversion Emission of Infrared Excited Er<sup>3+</sup>-Doped Transparent Glass Ceramics Containing CaF<sub>2</sub> Nano-Crystals</li><li>Structuration and Fabrication of Sensors Based on LTCC (Low Temperature Co-Fired Ceramic) Technology</li><li>Fabrication of Ba-Ti-B-Si-O Glass-Ceramics for LTCC</li><li>Crystallization of Cordierite-Based Glass-Ceramics Adding with Fe<sub>2</sub>O<sub>3</sub>-TiO<sub>2</sub></li><li>The Influence of Li<sup>+</sup> on the Sintering of Cordierite Glass Ceramic</li><li>Composition and Properties of the LZS Glass-Ceramics Used as Anodic Bonding Material</li><li>Preparation of SiO<sub>2</sub>-TiO<sub>2</sub> Films of High Photo-Catalytic Activity in the Electric Field Heating-Treatment</li><li>Sintering AlN Ceramics Below 1500 degreesC with MgO-CaO-Al<sub>2</sub>O<sub>3</sub>-SiO<sub>2</sub> Glass Addition</li><li>Synthesis of Glass Ceramic from Goldmine Tailings</li><li>Method for Estimating the Critical Cooling Rate for Glass Formation from Isothermal TTT Data</li><li>Effect of Phenolic Resin on the Basic Properties of Woodceramics and Biomorphic SiC Ceramics</li><li>Manufacturing Process of Activated Magnesia from Bittern and Dolomite</li><li>Activated Alumina Adsorbent Developed from Waste Aluminum Sludge</li><li>A New Method for Effective Utilization of Melted Solid Waste</li><li>Development of Glass Ceramic by Sintering and Crystallization of Glass from Phosphorus Slag</li><li>Sialite Technology and Cycle Economy</li><li>Preparation and Characterization of Porous Cordierite Ceramics from Coal Fly Ash</li><li>Photo-Catalytic Properties of Ceramic Coating of TiO<sub>2</sub></li><li>Microporous Ceramics Made by Silicon Carbide Whiskers</li><li>Clay Minerals as a Feasible Additive to Stabilize Cadmium in Contaminated Soils</li><li>Preparation and Photocatalytic Performance of Ag-Doped Titanium Dioxide Whiskers</li><li>A Novel Hydroxyapatite Carrier for Enrichment of Hydrocarbon Degradation Bacteria</li><li>Practice of Simulation to Formation of Rock Theory</li><li>Effect of Deposition Conditions on TiO<sub>2</sub> Thin Film on Silica Glass Fibers by Liquid Phase Deposition</li><li>Effects of Boron-Doped on Photocatalysis and Hydrophilicity of TiO<sub>2</sub> Film</li><li>Preparation of Sialon from Solid Wastes by Colloidal Process</li><li>Oxidation Resistance of Mild Steels Coated with Ce<sup>4+</sup>-Modified TiO<sub>2</sub> Nanofilms</li><li>Hierarchically Nanostructured Porous Functional Ceramics</li><li>Preparation and Photocatalytic Property of Platinum-Modified TiO<sub>2</sub> Ceramic Film Using Different Compound Techniques</li><li>Preparation and Photocatalytic Properties of Nanosized La<sup>3+</sup> and Co<sup>2+</sup> Co-Doped TiO<sub>2</sub> by Microemulsions</li><li>Preparation of Rare-Earth Element Doped Titanium Oxide Thin Films and Photocatalysis Properties</li><li>Influence of La<sup>3+</sup> Ions on the Photo-Catalytic Activity of TiO<sub>2</sub> Films Prepared by Micro-Plasma Oxidation Method</li><li>Dispersion and Electrophoretic Deposition of Titania Particles</li><li>Photo-Catalytic Activity of Fe<sup>3+</sup>/Sn<sup>4+</sup> Co-Doped Titanium Dioxide Nano-Crystalline Thin Films for Methyl Orange Degradation</li><li>Preparation of TiO<sub>2</sub>/SiO<sub>2</sub>/(?-Fe<sub>2</sub>O<sub>3</sub>-SiO<sub>2</sub>) Magnetic Photocatalyst</li><li>Preparation of N-Doped TiO<sub>2</sub> Photocatalytic Paint and its Sterilization Performance under Visible-Light Irradiation</li><li>Factors Influencing the Photocatalytic Efficiency in the Experimental for the TiO<sub>2</sub> Powder Slurry Systems</li><li>Photocatalytic Degradation of Methylene Blue Aqueous Solution under Visible Light Irradiation by Using N-Doped Titanium Dioxide</li><li>Growth of TiO<sub>2</sub> Thin Film on Glass Substrate by Air-Opened MOCVD</li><li>Preparation of WO<sub>x</sub>-TiO<sub>2</sub> and the Photocatalytic Activity under Visible Irradiation</li><li>Photocatalytic Degradation of Methyl Orange on ZnO in Aqueous</li><li>Photocatalytic Properties of Nanocrystalline Tin Oxide Synthesized by Using Molten Boric Acid as a Flux</li><li>Effects of Heat Treatment Temperature on the Photocatalytic Properties of TiO<sub>2</sub> Prepared by Melt-Phase Separation Process</li><li>Effect of CeO<sub>2</sub> Supports on CO Oxidation Activity of Pd-Cu Catalyst</li><li>Synthesis and Catalytic Activity Studies of V/K/Ca and V/Ks/Ce Based Catalysts for Diesel Soot Oxidation</li><li>Preparation of Nanosized Ca-Zn Ferrite Particles by a Sol-Gel Method and its Magnetic Properties</li><li>Synthesis of Bi<sub>4-x</sub>Yb<sub>x</sub>Ti<sub>3</sub>O<sub>12</sub> Nanopowders by a Modified Sol-Gel Process</li><li>Synthesis of Ce<sub>0.8</sub>Gd<sub>0.05</sub>Y<sub>0.15</sub>O<sub>1.9</sub> Nanopowders</li><li>Nano-Scaled Anatase Phase Titanium Oxide Converted from Ammonium Oxotrifluorotitanate Prepared by Aqueous Solution of Ammonium Hexafluorotitanate and Boric Acid</li><li>Effect of Low Frequency and Power Ultrasonic Treatment on the Surface Adsorbed Organics and Visible Light Photocatalysis Activity of Nanosized TiO<sub>2</sub> Photocatalyst</li><li>Effect of Drying Methods on Photocatalytic Activity of Nanosized Titanium Dioxide</li><li>Preparation of Nanosize Anatase TiO<sub>2</sub> Powders by Hydrothermal Synthesis</li><li>Synthesis of VO<sub>2</sub> Nanocrystalline via Hydrothermal Method</li><li>Synthesis of LaMnO<sub>3</sub> via a Mechanochemical Activated Process</li><li>Synthesis and Characterization of Regular Hexagonal NiCo<sub>2</sub>O<sub>4</sub> Nanosheets</li><li>Preparation and Characterization of CdSe Synthesized from Non-Aqueous Media</li><li>Preparation and Characterization of CdSe Nanoparticles Prepared by Using Ultrasonic Irradiation</li><li>Synthesis of Hollow Sphere CdSe from CdCl<sub>2</sub> Aqueous Solution Containing Ethylenediamine</li><li>Preparation and Characterization of Gallium-Doped Zinc Oxide Nanopowders with High Electrical Conductivity</li><li>Preparation of Conductive Composite Particles by Impact Coating Process</li><li>The Preparation of Alumina Nanopowders from Solution Derived Precipitates through Polymer Gel Method</li><li>Preparation of Nanoscale High-Purity ?-Alumina Powders</li><li>Effect of Phase of YAG Powder Synthesized by Co-Precipitation on Transparent Ceramic Sintering</li><li>A Novel Preparation Route of YAG:Ce via Polymer Gel Precursor</li><li>A Novel Non-Aqueous Solvent Chemical Process to Synthesize Nano-ZrO<sub>2</sub></li><li>Preparation of Pottery from Shale</li><li>Effect of Novel Bivalent Mineralizers on the Synthesis of Nano-Sized Y<sub>2</sub>O<sub>3</sub> Doped ZrO<sub>2</sub> Powder by Hydrothermal Method</li><li>Coloring Mechanism of Pr-CeO<sub>2</sub> Nano-Crystalline Red Lanthanide Pigments Prepared by Low-Temperature Combustion Synthesis</li><li>Preparation and Thermal Decomposition Mechanism of Zn<sup>2+</sup>-Doped Mg,Al-Hydrotalcite Nanocrystalline</li><li>Photoluminescence and Structural Properties of Si Nanoparticles Embedded in SiO<sub>2</sub> Matrix by Reactive RF Magnetron Sputtering</li><li>Preparation and Synthetic Mechanism of Silicon Carbide Nanometer Whiskers</li><li>Synthesizing Nano-Scale Titanium Nitride Powders by Solvothermal and Carbothermal Methods</li><li>Preparation and Some Properties of Ni-TiN and Ni-TiC Nanocomposite Particles by DC Arc-Plasma</li><li>Synthesis of WC Nanosized Powder by the Plasma Arc Discharge Process</li><li>Preparation and Property of Self-Dispersed Nanometer ?-AlOOH</li><li>Influence of Ultrasonic Irradiation Power on the Synthesis Kinetics of Nano-Hydroxyapatite Prepared by a Wet Chemical Process</li><li>Effects of Acidic Amino Acids on Hydroxyapatite Morphology</li><li>Surface Nano-Particle Coating of Fly Ash</li><li>Microstructure and Mechanical Properties of Silica Xerogels Doped with SiC Whisker and Short Carbon Fiber</li><li>Preparation of Nanocrystalline Nickel Powders by Chemical Reduction in Nonaqueous Media</li><li>Preparation and Characterization of Nano-Sized Ni Powders inside a Nonionic Polymer Network</li><li>Preparation of Nano-Ag Particles and Antibacterial Dope Loaded Silver</li><li>Effect of Dispersant on the Particle Size Distribution of Cu Powders Prepared by Wet-Reduction Process</li><li>Growth of Oxide Nanorod, Nanotube and Nanocable Arrays through Template-Based Sol Electrophoretic Deposition</li><li>One-Dimensional Oxide Nanomaterials through Rheological Self-Assembling</li><li>Synthesis and Electrochemical Properties of V<sub>2</sub>O<sub>5</sub> Nanostructures</li><li>Catalyst-Assisted Pyrolysis of Polymeric Precursors: A New Method to Synthesize Low-Dimensional Nanomaterials</li><li>Corrosion Resistance Properties of Carbon Nanotube Reinforced Electroless Composite Coating</li><li>Self-Assembled Monolayer of Silver Nanorods for Surface-Enhanced Raman Scattering</li><li>Synthesis and Characterization of La<sub>2</sub>(MoO<sub>4</sub>)<sub>3</sub> Microcrystals via Hydrothermal Microemulsion</li><li>Synthesis of Yttrium Oxide Hydroxide Nitrate Nanorods by Hydrothermal Method</li><li>Preparation of PPy Nanowires and its Amperometric Response to Nitrate</li><li>Structural and Optical Properties of Lead Titanate Nanowires Synthesized by Hydrothermal Method</li><li>SnO<sub>2</sub> Nanowires with Branched Structures Synthesized by Thermal Evaporation of Sn Powders</li><li>Synthesis of Sulfide Nanowire Arrays through Template-Assisted Electrodeposition</li><li>Synthesis and Characterization of Boron Carbide Nanobelts</li><li>Large-Scale Fabrication of ZnO Hexagonal Rods Arrays by a Simple Chemical Solution Method</li><li>Luminescent Properties of Aluminum Doped Zinc Oxide Nanofibers Prepared by Electrospinning</li><li>Influence of pH on the Morphology of Yttrium Oxide Hydroxide Nitrate Nanocrystal</li><li>Fabrication of LaNiO<sub>3</sub> Chain-Like Ceramics from Nanocable Precursors</li><li>Preparation and Characterization of Cerium Hydrate Fiber</li><li>Preparation of a Novel Carbon Nano-Material Studded Iron Granules from Needle Coke by Arc Method</li><li>Synthesis and Characterization of Refluxed Sols and TiO<sub>2</sub> Thin Films Using TiOSO<sub>4</sub></li><li>Preparation of TiO<sub>2</sub> Nanocrystalline Films by Electrophoretic Deposition and their Application in Dye-Sensitized Solar Cells</li><li>Dye-Sensitized Nanocrystalline TiO<sub>2</sub> Ceramic Film and its Photoelectricity Property</li><li>In Situ Template Synthesis of TiO<sub>2</sub> Nanotube Array Films</li><li>Anticorrosion Behaviours of the TiO<sub>2</sub> / WO<sub>3</sub> Composite Photoelectrodes for 304 Stainless Steel</li><li>Hydrothermal Conversion Deposition of ZnFe<sub>2</sub>O<sub>4</sub> Doped TiO<sub>2</sub> Thin Films and their Photovoltaic Response</li><li>The Photo-Induced Cathodal Protection of 304SS with Graded Bandgap Ferrite/TiO<sub>2</sub> Nanostructures</li><li>Microstructure and Resistivity of Iridium Oxide Thin Films by Pulsed Laser Deposition Technique</li><li>Effects of Nanosized Iron Oxide with Different Morphology on Nanomechanical Properties of Nanocomposite Coating</li><li>Transparent and Compact Zinc Oxide Thin Films via Two-Step Electrodeposition from Aqueous Solution</li><li>Microstructure and Mechanical Properties of Cr-C-N, Cr-Si-N and Cr-Si-C-N Coatings by a Hybrid Coating System</li><li>Structure and Optical Properties of Si Films Deposited by Inductively Coupled Plasma CVD at Room Temperature</li><li>Microstructure Control and Phase Structure Study of Porous Alumina Membrane</li><li>Fabrication and Characterization of the Multilayer Film Containing Polyoxometalate with Pendant Support-Ligand</li><li>Surface Morphology of Thin Film Deposited on Rotating Substrate by EB-PVD</li><li>Nanocomposites - Toughened Ceramics</li><li>Multifunctional BN/Si<sub>3</sub>N<sub>4</sub> and TiN/Si<sub>3</sub>N<sub>4</sub> Nanocomposites Prepared by In Situ Nitridation Method</li><li>Microstructure and Mechanical Properties of SiC-Al<sub>2</sub>O<sub>3</sub> Nanocomposite Prepared by Surface Modified SiC Nanopowders</li><li>Preparation and Properties of Al<sub>2</sub>O<sub>3</sub> Particle Dispersed 3Y-TZP Nanoceramics Doped with TiO<sub>2</sub></li><li>Microstructures and Multi-Toughening of ZrO<sub>2</sub> Nano-Micron Fibers Self-Toughening Al<sub>2</sub>O<sub>3</sub> Ceramics from In Situ Growth in the Melts Produced by Combustion Synthesis</li><li>Microstructures and Properties of Al<sub>2</sub>O<sub>3</sub>/ZrO<sub>2</sub> Composite Ceramics from In Situ Growth in the Melts Produced by Combustion Synthesis</li><li>From Kaolins (with Addition of Al<sub>2</sub>O<sub>3</sub>) to Mullite Composite Nanocrystals: Experiments and Analysis</li><li>Spectroscopic Study of Rod-Like Mesoporous ZnO-SiO<sub>2</sub> Composites</li><li>Role of Amorphous Silicon Carbide in Microstructure and Mechanical Properties of nc-TiC/a-SiC Nanocomposite Coatings Prepared by PECVD</li><li>Preparation and Characterization of CdSe/SiO<sub>2</sub> Nanocomposites by Sol Gel Method and In Situ Growth</li><li>Properties of Nano-Hybrid Sol-Gel Materials Synthesized from Colloidal Silica-Silane Containing Epoxy Silane</li><li>Preparation and Structural Characterization of SiO<sub>2</sub>-ZrO<sub>2</sub> Aerogels</li><li>Synthesis and Structural Characterization of SiO<sub>2</sub>-Al<sub>2</sub>O<sub>3</sub> Xerogels</li><li>Influence of Binder Additives on the Sintering of Nano-3Y-TZP</li><li>Sintering Behavior of Pure and Nb-Doped BaTiO<sub>3</sub> Powder Prepared by High-Gravity Reactive Precipitation</li><li>Preparation of MgAl<sub>2</sub>O<sub>4</sub> Transparent Nano-Ceramics and their Light Transmission Properties</li><li>Processing and Properties of Nanocrystalline Tetragonal Zirconia</li><li>Analysis of the Surface Adsorbed Organics of Nanosized TiO<sub>2</sub> Photocatalyst with High Visible-Light Photocatalysis Activity by Ultrasonic Treatment under Water and Ethanol Solution</li><li>Low-Temperature Synthesis and Micro-Morphology Observation of Transparent MgAl<sub>2</sub>O<sub>4</sub> Nano-Ceramics</li><li>Evaluation of a Shoe Cushioning System Using Shock Absorber by Biomechanics</li><li>Phase Transformation Behavior of ZrO<sub>2</sub>-TiO<sub>2</sub> Thin Films in Electric Field</li><li>Phase-Transformation Kinetics of TiO<sub>2</sub> in TiO<sub>2</sub>/(O'+?')-Sialon Multi-Phase Ceramics</li><li>Effect of Er<sup>3+</sup> Doping on Crystallization of PbF<sub>2</sub>-SiO<sub>2</sub> Based Bulk Xerogels</li><li>Phase Evolutions of High Energy Ball Milled Ni-66.7at% Si</li><li>Thermal Expansion Behavior of Solid Solution Y<sub>1.9</sub>R<sub>0.1</sub>Mo<sub>4</sub>O<sub>15</sub> (R = Sm, Nd, Dy)</li><li>Thermal Expansion Coefficients of Sm<sub>2</sub>Zr<sub>2</sub>O<sub>7</sub> Doped with MgO</li><li>Improved Stability of Mn-Doped WO<sub>3</sub> Varistor via Doping Cr<sub>2</sub>O<sub>3</sub></li><li>Effect of the Addition of Ti<sup>3+</sup> into TiO<sub>2</sub> Film on the Performance of Dye Sensitized Solar Cells</li><li>Reaction Process of Al-TiO<sub>2</sub>-C-Ti-Fe Multiphase System during Combustion Synthesis</li><li>Sintering Behavior of Fe-Si Composite Powder by DPR Technique</li><li>Reaction Process of Al<sub>2(1-x)</sub>Mg<sub>x</sub>Ti<sub>1+x</sub>O<sub>5</sub> Composite Powder by Chemical Co-Precipitation and Subsequent Sintering</li><li>Preparation and Investigation of TiO<sub>2</sub> Sol Containing Nanometer Anatase Crystalline Grains</li><li>Pressure Sensitivity of SiC/Cu Composites Prepared by SPS</li><li>Sintering Kinetic of Fine ?-Alumina Powder with ZrO<sub>2</sub> Impurity</li><li>On the Grain Size Distribution of MnO Doped ZnO Ceramics</li><li>Effect of Sintering Process on Microstructure of Al<sub>2</sub>O<sub>3</sub>/LiTaO<sub>3</sub> Composite Ceramics</li><li>Kinetics Model for the Initial Stage of Spark Plasma Sintering</li><li>Study on the Critical Time and Diffusion Coefficient in Grain-Boundary Segregation of Phosphorus</li><li>Fabrication of Highly Microstructure Controlled Ceramics by Novel Colloidal Processing</li><li>Shrinkages during from Liquid to Solid in Colloidal Forming</li><li>Suspension Characteristics and Rheological Properties of Aqueous Alumina/Zirconia Freeze Casting Slurries</li><li>The Stability of TZP-YSZ Binary Suspensions</li><li>Silicon Nitride Ceramic Prepared by Colloidal Process</li><li>Mechanical Properties of Filler Metal in Si<sub>3</sub>N<sub>4</sub>/Austenitic Stainless Steel/Si<sub>3</sub>N<sub>4</sub> Joints as Measured by Nanoindentation and its Relationship to the Interfacial Strength</li><li>Joining of SiC Ceramic by High Temperature Brazing Using Ni-Cr-SiC Powders as Filler</li><li>Joining of SiC Ceramic by Hot Pressing Reaction Joining Process Using Ni-51Cr Powders as Filler</li><li>Fractal Dimension of Al(OH)<sub>3</sub> Particle and Fractal Simulation of Boundary Micro-Topography</li><li>Evaluating Mechanical Properties of Ceramics by Relative Methods</li><li>The Compressive Strength of Ceramic Microbeads</li><li>Spherical Indentation on Glass-Coated Al<sub>2</sub>TiO<sub>5</sub>-Mullite Composites</li><li>Indentation Fracture Toughness and Hardness of Solid Oxide Fuel Cell Electrolyte Material</li><li>Description of the Nanoindentation Unloading Behavior of Brittle Ceramics with a Modified Surface</li><li>Cyclic Fatigue of Alumina Ceramics as Evaluated by Modified Small Punch Tests</li><li>Dynamic Fatigue of Y-TZP Ceramics at the Room Temperature</li><li>Cracking Stress of Nano-Fibers Composite Ceramics</li><li>Experimental Study of Micro Displacement Field of Microstate of Crack Tips of Ceramics Plasticized with Zirconia and Stabilized by Yttrium Oxide - Application of Digital Image Correlation Method Based on Analysis by Scanning Electron Microscope</li><li>Lower and Upper Bounds of Mechanical and Thermal Properties of Ceramic/Metal Composites</li><li>Fracture Enhancement of Mixed Mode I-II Transformation Toughened Ceramics</li><li>Crack Healing, Reopening and Thermal Expansion Behavior of Al<sub>2</sub>TiO<sub>5</sub> Ceramics at High Temperature</li><li>Corrosion Resistance of the Ceramic Coating Formed by Micro-Plasma Arc Oxidation on AZ91D Alloy</li><li>Influences of Duty Ratio on Structure and Corrosion Resistance of Ceramic Coatings on Ti-6Al-4V by Micro-Plasma Oxidation</li><li>
<sub></sub>Preparation and Wet Erosive Wear Characteristics of Porous Al<sub>2</sub>O<sub>3</sub> Ceramics</li><li>Erosive Wear Performance and Mechanism of Engineering Ceramic Materials</li><li>Erosion Wear Characteristics and Mechanism of Si<sub>3</sub>N<sub>4</sub> Ceramics: Effect of Impact Angle</li><li>Effect of Testing Parameters on Wear Properties of Alumina Strengthen 3Y-TZP Ceramics</li><li>Dry Friction Behaviour of Reaction-Bonded Silicon Carbide at High Temperature</li><li>Wear Mechanism of Ceramic Microbeads as Grinding Media</li><li>Oxidation Behavior and Mechanical Property of Si<sub>3</sub>N<sub>4</sub> Ceramics with Rare Earth Oxide Addition</li><li>Influences of Calcination Ambiences on Phase Composition and High Temperature Oxidation Resistance Property of Ceramic Coatings on Ti-6Al-4V Alloy by Micro-Plasma Oxidation</li><li>Geometric Design of Cycloidal Drives with Ceramic Ball Meshing Elements</li><li>Design of Ceramic Composite Based on the Impact Resistance and its Machining Application</li><li>Parallel Simulation of Ceramic Grain Growth on the Platform of MPI</li><li>Quantitative Evaluation for New Bone Growth of Bone Repairing Biomaterial Based on Color Image Segmentation</li><li>Application of Improved BP Neural Network in the Preparation Processing of the SrTiO<sub>3</sub> Nanocrystalline</li><li>Finite Element Method for Thermal Analysis and Ablative Calculation of Heat Protection Materials</li><li>Lifetime Control and Prediction of ZrO<sub>2</sub>/CePO<sub>4</sub> Composites</li><li>First-Principles Study of Nonmetal-Doped Titanium Oxides</li><li>First Principle Study on Electronic Structure of Nanocrystalline BaTiO<sub>3</sub> Ceramics</li><li>A Method to Evaluate the Elastic Properties of Ceramics-Enhanced Composites Undertaking Interfacial Delamination</li><li>First-Principles Calculations on Crystal Structure and Thermodynamic Properties of Ceramics</li><li>Adsorption of the Au Atom on Si(001) Surface</li><li>Area-Perimeter Relation of the Grains in Stabilized Cubic Zirconia</li><li>Effective Stiffness of Nano and Transformation Composite Ceramics</li><li>Lambdoidal Layup of Aragonite Sheets in Conch Shell</li><li>Serial Simulation of Ceramic Grain Growth Based on Ternary-Tree Structure and Space Partition</li><li>Electronic Structure Study of Ni/Al<sub>2</sub>O<sub>3</sub>/Ni from First-Principles</li><li>Assessment of the Surface Morphology of Diamond Film Based on Fractal</li><li>Effects of Ceramic Fillers on Light Reflectance and Arc Resistance of PTFE for Circuit Breaker</li><li>Preparation of Yellow Color Pearlescent Pigments of CeO<sub>2</sub>-Mica</li><li>Study of Carbonizing Processes for Sintered Dolomite</li><li>Preliminary Analysis of the Citations to Articles Published in Two Academic Journals</li><li>Grain Characteristics of Nanocrystalline ZrO<sub>2</sub> Powders</li><li>Analysis of Capacity to Make Profits in Chinese Listed Ceramic Companies</li><li>Structural Micro-Layered Ceramics with Surfaces under Tension and Compression with Increasing Apparent Fracture Toughness</li><li>Research on Morphology and Phase Structure of Al/Cu Interfaces Formed by Explosive Cladding</li><li>Fabrication of Layered Ti<sub>3</sub>SiC<sub>2</sub>/?-SiAlON Material</li><li>Microstructure and Optical Characterization of Au/SiO<sub>2</sub> Nano-Composite Multilayer Films</li><li>ZrO<sub>2</sub>-Ni Functional Gradient Bonding Interlayer</li><li>Microstructure and Mechanical Properties of Freeze Cast Alumina/Silicon Carbide Layered Composites</li><li>Mechanical and Electrical Properties of Boron-Oxygen-Nitrogen Film as Buffer Layer</li><li>Characteristics of Surfactant-Zirconium Phosphate Composites with Expanded Interlayer Separation</li><li>Resistance of the Transitional Region of Laser-Clad Coating on Electrolytic Low Titanium Aluminium Alloys to Multiple Impact Loading</li><li>Development of Functionally Structured Materials: Ceramic Photonic Crystals and Fractals</li><li>Functionally Graded Thermoelectric Materials</li><li>Microstructure and Properties of WC<sub>P</sub> Reinforced Ferrous Gradient Composites</li><li>Functionally Graded Piezoelectric Ceramics for Ultrasonic Transducers</li><li>Preparation of Functionally Graded Cu/AlN/Cu Electrode Materials for Thermoelectric Devices</li><li>A New Silver-Based Graded Composite as Electrical Contact Material</li><li>Bending Behavior of Functionally Graded Piezoelectric Laminated Actuators under Electric Fields</li><li>Thermal Shock Behavior of Nano-Structured Functionally Graded Thermal Barrier Coatings Deposited by Supersonic Plasma Spray</li><li>Numerical Simulation Method of Heat-Resistant Hetergeneous Graded Ceramics Structure on Vehicle</li><li>Experimental Study and Modeling of a Differential SMA Spring Actuator</li><li>Microstructure and Dielectric Properties of LiTiNiO Thin Films</li><li>Effect of Ti Content on Microstructure and Dielectric Properties of Li and Ti Co-Doped NiO Thin Films</li><li>Fabrication and Characterization of Ceramic/Metal Gradient Thermal Barrier Coating</li><li>Microstructure and Corrosion Behaviour of Ni/Al-Al<sub>2</sub>O<sub>3</sub> Gradient Ceramic Coatings on Q235 Steel</li><li>Macro-Residual Stress in 304 Stainless Steel Coated with ZrO<sub>2</sub>-CeO<sub>2</sub> Thin Films by Sol-Gel Process</li><li>XPS Studies on Composite ZrO<sub>2</sub>-CeO<sub>2</sub> Thin Films Deposited on Metal Substrate by Sol-Gel</li><li>Preparation of Copper Particles Coated with Amorphous Titania</li><li>Interfacial Cracks Control of Y-TZP/Stainless Steel FGM Fabricated by Slip Casting</li><li>Surface Aluminizing and Internal Oxidation of Cu-Al-Y Alloy</li></ul>
<sub></sub>Preparation and Wet Erosive Wear Characteristics of Porous Al<sub>2</sub>O<sub>3</sub> Ceramics</li><li>Erosive Wear Performance and Mechanism of Engineering Ceramic Materials</li><li>Erosion Wear Characteristics and Mechanism of Si<sub>3</sub>N<sub>4</sub> Ceramics: Effect of Impact Angle</li><li>Effect of Testing Parameters on Wear Properties of Alumina Strengthen 3Y-TZP Ceramics</li><li>Dry Friction Behaviour of Reaction-Bonded Silicon Carbide at High Temperature</li><li>Wear Mechanism of Ceramic Microbeads as Grinding Media</li><li>Oxidation Behavior and Mechanical Property of Si<sub>3</sub>N<sub>4</sub> Ceramics with Rare Earth Oxide Addition</li><li>Influences of Calcination Ambiences on Phase Composition and High Temperature Oxidation Resistance Property of Ceramic Coatings on Ti-6Al-4V Alloy by Micro-Plasma Oxidation</li><li>Geometric Design of Cycloidal Drives with Ceramic Ball Meshing Elements</li><li>Design of Ceramic Composite Based on the Impact Resistance and its Machining Application</li><li>Parallel Simulation of Ceramic Grain Growth on the Platform of MPI</li><li>Quantitative Evaluation for New Bone Growth of Bone Repairing Biomaterial Based on Color Image Segmentation</li><li>Application of Improved BP Neural Network in the Preparation Processing of the SrTiO<sub>3</sub> Nanocrystalline</li><li>Finite Element Method for Thermal Analysis and Ablative Calculation of Heat Protection Materials</li><li>Lifetime Control and Prediction of ZrO<sub>2</sub>/CePO<sub>4</sub> Composites</li><li>First-Principles Study of Nonmetal-Doped Titanium Oxides</li><li>First Principle Study on Electronic Structure of Nanocrystalline BaTiO<sub>3</sub> Ceramics</li><li>A Method to Evaluate the Elastic Properties of Ceramics-Enhanced Composites Undertaking Interfacial Delamination</li><li>First-Principles Calculations on Crystal Structure and Thermodynamic Properties of Ceramics</li><li>Adsorption of the Au Atom on Si(001) Surface</li><li>Area-Perimeter Relation of the Grains in Stabilized Cubic Zirconia</li><li>Effective Stiffness of Nano and Transformation Composite Ceramics</li><li>Lambdoidal Layup of Aragonite Sheets in Conch Shell</li><li>Serial Simulation of Ceramic Grain Growth Based on Ternary-Tree Structure and Space Partition</li><li>Electronic Structure Study of Ni/Al<sub>2</sub>O<sub>3</sub>/Ni from First-Principles</li><li>Assessment of the Surface Morphology of Diamond Film Based on Fractal</li><li>Effects of Ceramic Fillers on Light Reflectance and Arc Resistance of PTFE for Circuit Breaker</li><li>Preparation of Yellow Color Pearlescent Pigments of CeO<sub>2</sub>-Mica</li><li>Study of Carbonizing Processes for Sintered Dolomite</li><li>Preliminary Analysis of the Citations to Articles Published in Two Academic Journals</li><li>Grain Characteristics of Nanocrystalline ZrO<sub>2</sub> Powders</li><li>Analysis of Capacity to Make Profits in Chinese Listed Ceramic Companies</li><li>Structural Micro-Layered Ceramics with Surfaces under Tension and Compression with Increasing Apparent Fracture Toughness</li><li>Research on Morphology and Phase Structure of Al/Cu Interfaces Formed by Explosive Cladding</li><li>Fabrication of Layered Ti<sub>3</sub>SiC<sub>2</sub>/?-SiAlON Material</li><li>Microstructure and Optical Characterization of Au/SiO<sub>2</sub> Nano-Composite Multilayer Films</li><li>ZrO<sub>2</sub>-Ni Functional Gradient Bonding Interlayer</li><li>Microstructure and Mechanical Properties of Freeze Cast Alumina/Silicon Carbide Layered Composites</li><li>Mechanical and Electrical Properties of Boron-Oxygen-Nitrogen Film as Buffer Layer</li><li>Characteristics of Surfactant-Zirconium Phosphate Composites with Expanded Interlayer Separation</li><li>Resistance of the Transitional Region of Laser-Clad Coating on Electrolytic Low Titanium Aluminium Alloys to Multiple Impact Loading</li><li>Development of Functionally Structured Materials: Ceramic Photonic Crystals and Fractals</li><li>Functionally Graded Thermoelectric Materials</li><li>Microstructure and Properties of WC<sub>P</sub> Reinforced Ferrous Gradient Composites</li><li>Functionally Graded Piezoelectric Ceramics for Ultrasonic Transducers</li><li>Preparation of Functionally Graded Cu/AlN/Cu Electrode Materials for Thermoelectric Devices</li><li>A New Silver-Based Graded Composite as Electrical Contact Material</li><li>Bending Behavior of Functionally Graded Piezoelectric Laminated Actuators under Electric Fields</li><li>Thermal Shock Behavior of Nano-Structured Functionally Graded Thermal Barrier Coatings Deposited by Supersonic Plasma Spray</li><li>Numerical Simulation Method of Heat-Resistant Hetergeneous Graded Ceramics Structure on Vehicle</li><li>Experimental Study and Modeling of a Differential SMA Spring Actuator</li><li>Microstructure and Dielectric Properties of LiTiNiO Thin Films</li><li>Effect of Ti Content on Microstructure and Dielectric Properties of Li and Ti Co-Doped NiO Thin Films</li><li>Fabrication and Characterization of Ceramic/Metal Gradient Thermal Barrier Coating</li><li>Microstructure and Corrosion Behaviour of Ni/Al-Al<sub>2</sub>O<sub>3</sub> Gradient Ceramic Coatings on Q235 Steel</li><li>Macro-Residual Stress in 304 Stainless Steel Coated with ZrO<sub>2</sub>-CeO<sub>2</sub> Thin Films by Sol-Gel Process</li><li>XPS Studies on Composite ZrO<sub>2</sub>-CeO<sub>2</sub> Thin Films Deposited on Metal Substrate by Sol-Gel</li><li>Preparation of Copper Particles Coated with Amorphous Titania</li><li>Interfacial Cracks Control of Y-TZP/Stainless Steel FGM Fabricated by Slip Casting</li><li>Surface Aluminizing and Internal Oxidation of Cu-Al-Y Alloy</li></ul>