Spring International Conference on Material Sciences and Technology

<ul><li>Preface</li><li>Chapetr 1: Metallurgical Technologies and Materials Processing</li><li>Enlarged Zn Content Improves Fatigue Crack Propagation Resistance of Two Al-Zn-Mg-Cu Alloys with Multiple Aging Tempers</li><li>Study of Quench Sensitivity and Microstructure Evolution of Al-Mg-Si Alloy Sheets</li><li>Effect of the Inhomogeneity of Material Properties on the Quenching and Pre-Stretching Residual Stress in Aluminum Alloy</li><li>Integrated Design and Manufacturing of Aviation Aluminum Alloy Support Based on SLM Technology</li><li>Impurity Characterization by LA-ICP-MS in Terbium Metal after Solid State Electrotransport Purification</li><li>Effects of Deformation Rate on the Mechanical Properties of an Industrial Al-Zn-Mg-Cu Alloy</li><li>Effect of Fe-Rich Phases on Fracture Toughness of High Strength Al-Zn-Mg-Cu Alloy</li><li>Effect of Cu Content on the Microstructures of As-Cast and Homogenized Al-Cu-Mg-Ag Alloys</li><li>Effect of Zn/Mg Ratio on Microstructure Evolution of Al-Zn-Mg-Cu Alloys during Homogenization</li><li>Second Phase Dissolution Evolution of an As-Cast Al-4.0Cu-1.0Li-0.4Mg-0.3Ag-0.1Zr Alloy during Multiple Homogenization Processes</li><li>Regulate and Control Grain Structure Characteristics and Mechanical Properties Control of Al-Zn-Mg-Cu Alloy</li><li>Study on the Microstructure and Mechanical Properties of Dynamic Recrystallization of Metastable ? Titanium Alloy</li><li>Study on Microstructure and Mechanical Properties of Al_0.5TiNbX_0.5 High-Entropy Alloys</li><li>Effect of Pre-Deformation Degree on the Mechanical Properties and Microstructural Evolution of a Novel Al-Cu-Li Alloy</li><li>Metal Injection Molding Using Gas-Assisted Technology for Optimizing Density Uniformity and Part Weight Reduction</li><li>Simulation Research on Cold Extrusion Strengthening and Reaming of 7050 Aluminum Alloy Plate Hole</li><li>Effect of Sr and Ni Addition on Microstructure, Tensile Behavior and Electrical Conductivity of Squeeze Cast Al-6Si-3Cu Al Alloy</li><li>Chapter 2: Polymers and Composites</li><li>Technical Analysis and Overview of Recent Advances in Materials Science of Polymers, Polymer Composites and Polymer Nanocomposites</li><li>Study on Failure Characteristics of Typical Rivet Connections of C/SiC Composites</li><li>Study on Clove Oil Microcapsule with Montmorillonite /Polyurethane Hybrid Wall</li><li>Study on the Properties of Chemical Foaming Injection Molded Polyolefin/Chitosan Composites</li><li>Tensile Strength and Morphological Behavior of Treated Oil Pam Empty Fruit Bunch Particle Reinforced Polymeric Composite</li><li>Surface Improvements on Silver Streak Marks of Injection Molded Moisture Plastics Using Gas Counter Pressure and Plasticizing Optimization</li><li>Effect of Concentration of Electrolyte Solution on the Electrochemical Stability of Ionogel</li><li>Chapter 3: Computational Materials Science</li><li>A Perspective on Metamaterials for the Biomechanics Application: Multi-Material Metamaterial (4M) Structures</li><li>A Material Tolerable State Maximum Probability Timing: The Elements of the Uncertainty Measure Conditional Optimization Doctrine</li><li>Investigation of Terahertz Wave Propagation along Symmetric Coplanar Strpline on Multilayer Dielctric Substrates</li></ul>