Materials Science and Processing, Environmental Engineering and Information Technologies

Preface and Organizing Committee
Chapter 1: Materials for Mechanical Engineering and Technologies of Materials Processing
Wear Behaviors of PCBN Tools in Interrupted Turning Hardened Steel with Tool's Chamfer Angle and Edge Preparation Considered
Sintering of Frustum Shaped Polycrystalline Diamond Compact at Non-Hydrostatic Pressure
Experimental Research on Fabrication Process of Metal Powder for SLS
Hot Sizing Experiment Study of TC4 Titanium Alloy Bending Plate
Finite Element Analysis of Coating Interface Stress Field of Laser Cladding CBN Coating on Titanium Alloy
Dynamic Performance at Inner Tip of an Interfacial Crack near a Circular Cavity in Piezoelectric Bi-Materials
Target Curve Setting Model for Automatic Flatness Control on Stand 5 of 2180 mm Tandem Cold Rolling Mill
Synthesis, Characterization and Smart-Release Organic Inhibitor for Anticorrosion Coating
Progress on the Precious Metals Used in High-Temperature Protective Coatings
Erosion Resistance of TiB2 Particla Reinforced Metal Matrix Composite Coating
High Temperature Oxidation Studies of Al Coating Deposited by Magnetron Sputtering
Process Parameters Optimization of Plasma Spraying Nanostructured Coating Based on Particle Swarm Optimization Algorithm
Influence of Grain Size on Bake Hardenability for Low Carbon Steel by Internal Friction Method
State Analysis and Life Evaluation on Reformer Furnace Pipe Used for 100000hrs
Sintering of Fine Grained Polycrystalline Cubic Boron Nitride Compacts without Binder
Study of Process of Hot-Dipped Galfan Coating on Q235 Structural Steel
Metal/Ceramic Laminar Composite Immersion Heater for Heating Hot Dip Galvanizing Zinc Kettle
Influence of pH on Electroless Ni-P-?Al2O3 Composite Plating on AZ91D Magnesium Alloy by Ultrasonic Wave
Fabrication of Artificial Periodic Defects in Colloidal Photonic Crystals by Photolithography
Research on the Surface Topography Model of Galvanized Steels in Sheet Metal Forming
Corrosion Resistance Dependence of Rare Earth NiCrMoY Alloy Coatings
Simulation of InAIN/Si Single-Heterojunction Solar Cells Using wxAMPS
A Novel Nickel/Iron-Layered Double Hydroxide for Supercapacitors
Fabrication and Microstructure of Ge-Sb-S-CsCl Chalcogenide Glass Containing ?-GeS2 Nanocrystals
Theoretical Study of the Electronic Structures of Na-Doped ZnO
Analysis on the Anodizing Process of AZ31 Magnesium Alloy in an Environmental Friendly Alkaline Electrolyte
Molecular Modeling of the Mechanical Effect in the Chemical Mechanical Polishing Process
Effect of Rapid Thermal Annealing on Resistive Switching Uniformity of HfAlOx Based RRAM Devices
Chapter 2: Building Materials and Construction Technologies
Review on Chloride Penetration of Recycled Aggregate Concrete
Research on Strength Properties of Concrete Using Aggregates from Repeatedly Recycling Concrete Waste
Studies on Key Technology and Toughness of Super Sulfate Cement-Based Compound Materials
Research on Carbonation of Recycled Aggregate Concrete Using Different Recycled Concrete Aggregates
Research on Frost Resistance of Recycled High Performance Concrete
On Properties of Recycled Fine Aggregate for Structural Concrete from Repeatedly Recycling Concrete Waste
Cathodic Prevention and Cathodic Protection of Zinc Mesh Sacrificial Anode for Reinforced Concrete in 15% Salt Water
Preparation and Mixture Ratio Design of Foam Concrete with Lightweight Tailings
The Test Research on Non-Destructive Concrete ?Gravel? Strength Survey of Rebound Method Based on SVM
Discussion the Rheological Properties of Asphalt Rubber
Fire Resistance Test of Concrete Composite Box Steel Girder Floor System
The Influence of Different Hydrophobic Agent on the Water Absorptivity of Foam Concrete
Finite Element Analysis of Lightweight Energy-Saving Composite Floor
The Mechanical Properties of Lightweight Concrete under Different Factors
Experimental Study on the Mechanical Properties of Renewable Rubber Building Template
The Experiment Study on Parameters of Duncan-Chang Model for Silt Based on Different Water Content
The Mechanical Properties of Different Soil Moisture Content of Silt Study Based on the Experimental
Mechanical Properties and Permeability of Previous Color Recycled Aggregate Concrete
The Dam Anti-Seismic Dynamic Analysis of Wangwu Reservoir Reinforcement Project
Chapter 3: Chemical Materials and Chemical Engineering
Study on Separation/Enrichment of Trace Nickel in Water Samples Using Ammonium Sulfate-Dithizone-Cetyl Trimethyl Ammonium Bromide System
Tungsten Ionic Liquid: Synthesis and Physicochemical Property
Intrinsic Kinetics of Coking Crude Benzene Hydrodesulfurization on a Ti Modified Co-Mo-P/?-Al2O3 Catalyst
Colloidal Dispersion of High Solid Loading ZnO Powders with 2 wt% Al2O3 Stabilized with Polyelectrolyte
Preparation and Characterization of Polymerized Rosin/Polyacrylates Composite Miniemulsions
Kinetic Investigation of Thermal Decomposition Reaction of Ethane-1,2-Diamine Copper(II) Chloride, C2H8N2CuCl2
A Novel Hexaaluminate Material: Preparation, Characterization and Catalytic Activity in Methane Combustion
Synthesis and Characterization of Manganese Phosphate Aluminosilicate Molecular Sieve
Research of Chemical Coloring Technology on Pure Copper
Preparation of a Novel Composite Nanofiltration Membrane
The Structure and Properties of Lysine Doped Polypeptide Modified Polypyrrole Nanoparticles
Thermal-Oxidation Degradation and Evaluation of Non-Durable Non-Woven Fabrics
Formation and Photo-Degradation Performance of Titania Nanotubes
Photocatalytic Water Splitting over Ag/TiO2 Nano-Wire Films
Synthesis and Optical Properties of Copolymeres Bisphenol A and D-?-A Chromophores
Preparation of ZnAc/PVP Composite Fibers and ZnO Nanofibers
Synthesis and Electrochromic Properties of Fluorescent PEDOT/PSS Composite
A New Intumescent Flame Retardant on Epoxy Resin
Molecularly Imprinted Solid-Phase Extraction: Extraction of Traditional Chinese Medicine Active Ingredients
P-Toluene Sulfonic Acid Doped Polyaniline/Carbon Nanotube Nanocomposites by a Sequential Doping-Dedoping-Redoping Process
Mechanical Properties of Fumed Silica/PP Composites
Inhibition of TGF?-Saporin on Neointimal Hyperplasia via Inhibiting Smooth Muscle Cells Proliferation and Promoting its Apoptosis
Synthesis and Characterization of Carboxyl-Terminated Hyperbranched Polyester
Melting and Crystallization Properties of Crystalline/Crystalline Blends of Poly(Trimethylene Terephthalate) and Poly(Ethylene Terephthalate)
Preparation of Polyethylene with Vanadium/Titanium Bi-Metal Ziegler-Natta Catalysts
Desulfurization of Model Gasoline by Adsorption Process with Ruthenium Ion Modified Y-Zeolites
Effect of Nano-Calcium Carbonate on the Mechanical Properties of Polypropylene
Morphology, Mechanical and Thermal Properties of the Blends of Poly(Trimethylene Terephthalate)/Acrylonitrile-Styrene-Acrylic Copolymer
Chapter 4: Environmental Friendly Materials
Design and Development of Crystal Eco-Brick Shell
Synthesis and Characterization of Photocurable Biodegradable Elastomers
Construction of cDNA Library of Hansenula anomala
The Characterization of Chitosan Nanoparticles by Raman Spectroscopy
Electrospinning of Poly(Lactic Acid)/Poly(Lactic Acid-Co-Lysine) Blend
Effect of Sodium Benzoate on the Crystallization Behavior of Poly (3-Hydroxybutyrate-Co-4-Hydroxybutyrate)
Preparation Eco-Cement with Semi Dry FGD Ash from Steel Plant
Fabrication of Non-Load Bearing Cotton Stalks Bales and Pressure-Resistant Property Test
Study on Characteristics of Lactobacillus rhamnosus on Lactic Acid Fermentation with Different Substrates
Synthesis of Composite TiO2/Natural Cotton Cellulose Nanofiber with Photocatalytic Property
Chapter 5: Prevention of Pollution the Water Environment and Processing of Wastewater
Phosphorus Speciation and Vertical Variation in Sediments from Lake Baihua
Determine the Moisture Distribution in Sewage Sludge by Drying Differential
Investigation on Treatment of Phosphate-Containing Waste Water by Pyro-Modified Fly Ash
Source of Heavy Metals in Sludge of Huoshaogou Wetland Park in Xining
The Study of Denitrification Rate and N2O Release Rate in Shuangtaizi Estuary Wetland
Water Pollutant Control for a River-Lake Region to the Northwest of Lake Taihu
Impact of Nutrients and Temperature on Algal Growth and Relative Abundance of Xixi Wetland, China
Study on Treatment of Landfill Leachate Using an Integrated KMnO4 Oxidation and Diatomite Adsorption Method
Research on the Mechanism of Sulfate Pollution of Groundwater in Jiaozuo Area
Research Progress of Coal Flocculat in Recent Years
Improvement Measures of ORP in Subsurface Wastewater Infiltration System
The Research on Anaerobic Bio-Hydrogen Production Using UASB Reactor from Molasses Wastewater
Comparison of THMs Formation between Chlorination and Chloramination of Simulated Water with TiO2 and UV Pretreatment
Effect of Cyclodextrins on Photodegradation of 4,4-Bis(4-Hydroxyphenyl)Pentanoic Acid under UV Irradiation
Section Turbulent Distribution of the Stratified Shear Flow in the Braided River
Distribution and Pollution Assessment of Heavy Metals in Surface Sediment in Yellow River Estuary and the Adjacent Sea Area
Effects of Nitrate Concentration on Heterotrophic Denitrification in Wastewater Using Poly (Butylene Succinate) as a Carbon Source and Carrier
Removal of Methylene Blue from Aqueous Solution by a Novel PAA@Fe-Si Composite Material
Photocatalytic Degradation of Methyl Orange by Cu2O-MoO3
Screening and Characterization of a Bacterium Capable of Simultaneous Heterotrophic Nitrification and Aerobic Denitrification at High Concentrations of Ammonia-Nitrogen
Fixed-Bed Adsorption of Methylene Blue from Aqueous Solutions by Porous Starch
Selective Removal of As(V) from Aqueous Solutions Using Magnetic As(V)-Imprinted Polymers with Combination of Two Functional Monomers
Electrodeposition of Porous Polyaniline Coating on an Etching Stainless Steel Wire as a Fiber for Solid-Phase Microextraction of Triclosan and Chlorophenols in Water Samples
Chapter 6: Solutions in Environmental Engineering
Distribution and Fractionation of Lead and Cadmium in a Long-Term Zinc Smelting Areas
High Effective Utilization of Metallurgical Solid Waste in Pelletizing Process
Ecological Risk Assessment of Oxytetracycline Bacteria Residue in the Process of Fertilizing
Calculation of Carbon Dioxide Emission in Nanjing City and its Influencing Factors
Catalytic Oxidation Removal of HCN in Tail Gas
Haze Formation and the Influence of Ethanol Gasoline of Severe Cold Area on Haze
Microbial Properties and Degradation of Polycyclic Aromatic Hydrocarbons in the Contaminated Farmland Soil with Bioremediation
Research on a "Green" Industry Chain of Phosphate Fertilizer
Growth and Physiological Effects of Model Acid Rain and Lead Contamination to Tall Fescue Seedlings
Investigation on Soil Physiochemical Properties and Heavy Metal Contamination Characteristics in Two Types of Sites
Application of Machine Vision Coupling Pattern Matching Technology in Environment Design
Inhibitory Effects of Aqueous Extracts from Leaves of Common Tropical Green Plants on Nitrification in Soils
Predicting Carcinogenicity of Anilines by Quantitative Structure-Toxicity Relationship
Harvesting of Polycyclic Aromatic Hydrocarbons (PAHs)-Degrading Bacteria by Magnetic Flocculation
QSTR Study for the Carcinogenicity of Alkylbenzenes
Quantitative Structure-Toxicity Relationship for Predicting Acute Toxicity of Alkylbenzenes

Photodegradation of Bis(4-Hydroxyphenyl) Methane Based on the Inclusion of Two Cyclodextrins under Ultraviolet Irradiation
Adsorption of Bisphenol A from the Solution by ?-Cyclodextrin Modified TiO2
Effect of ZnO Nanoparticles on Medicago sativa at the Germination Stage
Chapter 7: Engineering Solutions in Mechanical Engineering
About Discretization of the Horizontal Drill-String Model with Uncertainty on the Frictional Force by the Lumped Parameters Method
Stability Analysis of Drill Rods as Shells in the Gas Stream
Double-Rotor Continuous Mixer Mixing Rubber Components of a Computer Simulation Analysis
Design and Drop Test of Aircraft Landing Gear's Shock Absorber Based on Magnetorheological Damper
Characteristics Study of Sewage Source Heat Pump System Based on Heat Transfer Enhancement and Acoustic Cavitation Decontamination
The Combustion and Emission Characteristics of Rapeseed Oil/Diesel Blended Fuel
Performance Improvement of Dye Sensitized Solar Cells by Using a Novel Operation Mode
PID and LQR Control for Two-Wheeled Vehicles with Hand Sensors
A SAW Filter of Elliptic Structure IDT
Outdoor Mobile Robot Navigation System Based on BCI and Dual Laser Radar
The Design of Control System of Cursor Movement Based EEG
Chapter 8: Applied Information Technologies, Communication and Data Processing
Sparse Incremental Delta-Bar-Delta for System Identification
A Leakproof Secret Sharing Scheme Based on Environment Sensing
Key Management in Wireless Sensor Networks: Development and Challenges
A Proposed Architecture for Instrumentation Cloud
Rule Extraction Based on Interval-Valued Rough Fuzzy Sets
The Analysis of the Loss Rate of Information Packet of Double Queue Single Server in Bi-Directional Cable TV Network
Regional Economic and Social Harmonious Degree Evaluation Model Using Intuitionistic Fuzzy Set
The Application of Image Entropy in the Recognition of Free Fluid Spread Motion
The Collaborative Exploitation of Vehicle Electrical and Electronic
Research on the Simulation Technology of Virtual Hand Interventional Manipulation in the Virtual Environment
Feature Extraction Method for Network Intrusion Detection Based on RS-KPCA
Rigid Medical Image Registration Based on Genetic Algorithms and Mutual Information
The Research of Reconfigurable Embedded System Based on FPGA
Study on the Optimal Image Resolution for Image Segmentation
FPGA-Based Dual-Polling Control System Design in WSN
Research of Drug Name Entity Recognition Based on Constructed Dictionary and Conditional Random Field
Improvement of Clustering Algorithm for WSNs
Enhancing Operations of Supply Chain Management through a Responsive Information Framework