7th Asia Conference on Mechanical and Materials Engineering

<ul><li>Preface</li><li>Chapter 1: Engineering Tribology and Surface Engineering</li><li>Friction and Wear Properties of Oriented Fe₂B with Different Cr Additions under Water-Lubricated Condition</li><li>Simulation Study on Erosion Wear Rule of Aluminium Brass Throttling Ring of Artillery Based on Finite Element Method</li><li>Metal Magnetic Memory Testing of the Drilling Riser Pipeline Steel Based on Pulsating-Impact-Fatigue Test</li><li>Numerical Simulation and Experimental Verification of Ultra-High Frequency Induction Cladding with Metal Wire</li><li>6061 Aluminum Surface Treatment by High Quality Coloring Anodic Film</li><li>Optimized Micro-Arc Oxidation Coating Thickness on ALZ Magnesium Lithium Alloy</li><li>Chapter 2: Steel and Alloys</li><li>A Study on Fabrication and Morphology of 6061 Aluminum Alloy in Hard Anodization</li><li>The Microstructure Evolution and Precipitation Behavior within HSLA Steels with Different M/C Atomic Ratios</li><li>Studying of Influence of Rotation of the Spent Electrode on the Microfirmness of the Received Preparation of Steel AISI 420 at Electroslag Remelting</li><li>Study of TiC Interaction and its Reaction Products with the Different Carbon Content Steels</li><li>Chapter 3: Biomaterials and Materials for Environmental Engineering</li><li>Analysis of the Influence of Pore-Forming Agent and Coagulation Bath on the Preparation of PES Hollow Fiber Membrane</li><li>Development Carbonated Hydroxyapatite Powders from Oyster Shells (<i>Crassostrea gigas</i>) by Carbonate Content Variations</li><li>Carbonated Hydroxyapatite Derived from Snail Shells (<i>Pilla ampulacea</i>): The Influence of Sintering Temperature on Purity and Crystallography Properties</li><li>Strength and Bioactivity of Hydroxyapatite/White Portland Cement (HAp/WPC) under Simulated Body Fluid (SBF) Solution</li><li>Adsorption of Metalworking Fluids in CSTR Reactor by Modified Sugarcane Bagasse with Aluminium Sulphate as Adsorbent</li><li>Chapter 4: Nanomaterials and Nanotechnologies</li><li>Anti-Buckling Design of Rectangular Thin Plate Based on Local Surface Nanocrystallization</li><li>Energy Absorption Analysis and Optimization Design of Local Surface Nanocrystallization Rectangular Tubes</li><li>Removal of Methylene Blue Dye Using Metal-Free g-C₃N₄ Photocatalyst over Natural Sunlight Irradiation</li><li>Flexural Wave Propagation of Double-Layered Graphene Sheets Based on the Hamiltonian System</li><li>Nickel Cobaltite Nanoneedle/Porous Graphene Nanosheets Network Nanocomposite Electrodes with Ultra-High Specific Capacitance for Energy Storage Applications</li><li>Microwave Absorption Properties of Porous Co/C Nanofibers Synthesized by Electrospinning</li><li>Literature Review of Gallium: Conductive Ink Alternative?</li><li>Chapter 5: Composite Materials</li><li>Utility of Air-Entraining Additive in the Development of Lightweight Alumina-Based Refractories</li><li>Tribological Properties of Carbon Fiber Epoxy Resin Composite and Polyimide Material at High and Low Temperatures</li><li>Numerical Study on Axial Crushing of Auxetic Foam-Filled Square Tube</li><li>Direct Recycling of Aluminium Chips into Composite Reinforced with <i>In Situ</i> Alumina Enrichment</li><li>Hybrid Effect of ZrB2+Si3N4 on the Microstructure and Mechanical Properties of AA8011 for Service Life Improvement</li><li>Effect of Heat Treatment Process on the Hardness of Aluminium356/Silicon Carbide Particulate Composites</li><li>An Application of Reinforced Polyurethane Foam in Design of the Common Bulkhead for Cryogenic Tanks</li><li>Chapter 6: Civil Engineering Materials</li><li>Adapting ANFIS to Improve Field Rebound Hammer Test for Concrete Compressive Strength Estimation</li><li>Analysis of Physical and Microstructural Properties on Parit Nipah Peat Particles as Sustainable Asphalt Modifier</li><li>A Characteristic and a Precisely Constitutive Model for Undrained Clay</li><li>Appraisal on Different Sustainable Road Stabilization Techniques for Different Road Condition and Materials</li><li>Chapter 7: Materials Processing and Forming</li><li>Size Effect of Drill Bit on Coupled Vibrations during High Speed Micro-Drilling Process of Composite Printed Circuit Board</li><li>Effects of Former Surface Treatment on Natural Rubber Latex Deposition</li><li>Effect of Hot Extrusion Parameters on Tensile Strength and Fracture Behavior in Direct Recycling of Aluminium Alloy (6061) Chips</li><li>Optimization of Material Removal Rate and Dimensional Errors in Subtractive Rapid Prototyping of Polycarbonate Material</li><li>Numerical and Experimental Analysis on Runner and Gate Positioning for Magnesium Alloy Die-Casted Test Piece</li></ul>