The Green Guide to Specification
An Environmental Profiling System for Building Materials and Components
Published on 8. January 2002
Book
Hardback
112 pages
978-0-632-05961-4 (ISBN)
Description
How can you tell if the materials and components you are specifying have a low environmental impact? A full life-cycle assessment is a complex, time-consuming and expensive process; the environmental ratings summarised in this Guide provide a quick and easy way for designers and specifiers to assess their options.
The relative environmental performance of over 250 materials and components have been assessed in this guide, using carefully researched, quantitative data derived from the BRE Environmental Database. A wide range of alternative specifications are provided for:
? walls
? floor systems
? floor finishes
? roofs
? windows
? doors
? ceilings
? paints
? insulation
? landscaping.
The performance of each specification is measured against a range of environmental impacts including:
? climate change
? toxicity
? fossil fuel and ozone depletion
? levels of emissions and pollutants
? mineral and water extraction.
Environmental performance is indicated by a simple to use A-B-C rating system. To further aid specifiers, guidance on capital coasts, typical replacement intervals and information on recycling is also provided for each material and component.
An important part of BREEAM, the BRE's widely accepted scheme to improve the environmental performance of buildings, The Green Guide to Specification is an essential tool for architects, surveyors, building managers and property owners seeking to reduce the environmental impacts of building materials through informed choice.
The relative environmental performance of over 250 materials and components have been assessed in this guide, using carefully researched, quantitative data derived from the BRE Environmental Database. A wide range of alternative specifications are provided for:
? walls
? floor systems
? floor finishes
? roofs
? windows
? doors
? ceilings
? paints
? insulation
? landscaping.
The performance of each specification is measured against a range of environmental impacts including:
? climate change
? toxicity
? fossil fuel and ozone depletion
? levels of emissions and pollutants
? mineral and water extraction.
Environmental performance is indicated by a simple to use A-B-C rating system. To further aid specifiers, guidance on capital coasts, typical replacement intervals and information on recycling is also provided for each material and component.
An important part of BREEAM, the BRE's widely accepted scheme to improve the environmental performance of buildings, The Green Guide to Specification is an essential tool for architects, surveyors, building managers and property owners seeking to reduce the environmental impacts of building materials through informed choice.
More details
Edition
3rd Edition
Language
English
Place of publication
Oxford
United Kingdom
Publishing group
John Wiley and Sons Ltd
Target group
College/higher education
Professional and scholarly
Dimensions
Height: 306 mm
Width: 221 mm
Thickness: 13 mm
Weight
632 gr
ISBN-13
978-0-632-05961-4 (9780632059614)
Copyright in bibliographic data and cover images is held by Nielsen Book Services Limited or by the publishers or by their respective licensors: all rights reserved.
Schweitzer Classification
Other editions
New editions
Jane Anderson | David Shiers
The Green Guide to Specification
Book
01/2009
4th Edition
Wiley
€128.75
Article is exhausted; no reprint
Previous edition
Nigel Howard | Mick Sinclair | David Shiers
The Green Guide to Specification
An Environmental Profiling System for Building Materials and Components
Book
01/1998
2nd Edition
IHS BRE Press
€63.33
Article exhausted; check for reprint
Content
Introduction;.
Background to the Green Guide to Specification;.
How the Green Guide to Specification was compiled;.
How to use the Green Guide to Specification;.
Green Guide ratings.
High-mass elements;.
Upper floor construction;.
Ground floors and substructure;.
Insulation;.
External walls;.
Superstructure.
Insulation.
Traditional cavity wall construction;.
'Rainscreen' claddings;.
Cladding and masonry;.
Cladding systems and framed construction;.
Roof Construction;.
Insulation;.
Flat roofs;.
'Traditional' pitched roofs.
Low pitched metal deck and roof cladding;.
Medium and Low-mass elements;.
Floor finishes and coverings.
Hard floor finishes.
Soft floor coverings;.
Substructural floor systems/floor surfacing;.
Windows and curtain walling;.
Internal walls and partitioning;.
Load bearing partitions.
Non-load bearing partitions;.
Proprietary and demountable partitions;.
Suspended ceilings and ceiling finishes;.
Doors;.
Other materials and elements.
Internal paint finishes;.
Insulation;.
All insulations (including those using HCFC's).
Zero ozone depletion potential (ZODP) insulations.
Landscaping: hard surfacing;.
Landscaping; boundary protection;.
Part IV Appendices;.
Appendix 1: general notes relating to the use of specific materials and particular environmental issues;.
Timber;.
Indoor air quality issues;.
CFC's, HCFC's and HFC's;.
PVC;.
Appendix 2: worked example of the generation of a Green Guide rating for an.
internal wall specification;.
Generation of the environmental profile for the specification;.
Generation of the Green Guide rating for each environmental issue;.
Generation of the summary rating for each specification;.
Appendix 3: the production of a BRE environmental profile for a material.
using the BRE environmental profiles methodology;.
Inventory analysis;.
Impact assessment;.
Appendix 4: BREEAM case study;.
Appendix 5: differences in environmental issues from previous editions;.
Contacts and further information;.
Key references;.
Index
Background to the Green Guide to Specification;.
How the Green Guide to Specification was compiled;.
How to use the Green Guide to Specification;.
Green Guide ratings.
High-mass elements;.
Upper floor construction;.
Ground floors and substructure;.
Insulation;.
External walls;.
Superstructure.
Insulation.
Traditional cavity wall construction;.
'Rainscreen' claddings;.
Cladding and masonry;.
Cladding systems and framed construction;.
Roof Construction;.
Insulation;.
Flat roofs;.
'Traditional' pitched roofs.
Low pitched metal deck and roof cladding;.
Medium and Low-mass elements;.
Floor finishes and coverings.
Hard floor finishes.
Soft floor coverings;.
Substructural floor systems/floor surfacing;.
Windows and curtain walling;.
Internal walls and partitioning;.
Load bearing partitions.
Non-load bearing partitions;.
Proprietary and demountable partitions;.
Suspended ceilings and ceiling finishes;.
Doors;.
Other materials and elements.
Internal paint finishes;.
Insulation;.
All insulations (including those using HCFC's).
Zero ozone depletion potential (ZODP) insulations.
Landscaping: hard surfacing;.
Landscaping; boundary protection;.
Part IV Appendices;.
Appendix 1: general notes relating to the use of specific materials and particular environmental issues;.
Timber;.
Indoor air quality issues;.
CFC's, HCFC's and HFC's;.
PVC;.
Appendix 2: worked example of the generation of a Green Guide rating for an.
internal wall specification;.
Generation of the environmental profile for the specification;.
Generation of the Green Guide rating for each environmental issue;.
Generation of the summary rating for each specification;.
Appendix 3: the production of a BRE environmental profile for a material.
using the BRE environmental profiles methodology;.
Inventory analysis;.
Impact assessment;.
Appendix 4: BREEAM case study;.
Appendix 5: differences in environmental issues from previous editions;.
Contacts and further information;.
Key references;.
Index